Harman Kardon AVR500 Owners Manual - Page 27
Multiroom Setup
View all Harman Kardon AVR500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
Multiroom Operation The AVR500 is fully equipped to operate as the control center for a sophisticated multiroom operation with optional remote external InfraRed (IR) sensors, speakers and power amplifiers. Although some multi- room installations will require the services of a specially trained installer, it is possible for the average do-it-yourself hobbyist to install a simple remote room system. Installation The key to remote room operation is to link the remote room to the AVR500's location with wire for an infrared receiver and speakers or an amplifier. For complete installation instructions for Multiroom use, see page 14. Multiroom Setup Once the audio and IR link connections have been made, the AVR500 needs to be configured for multiroom operation using the steps below. When making these selections, you may use the front-panel Information Display, or use the OnScreen Display System. Either the Semi-OSD system may be used, in which case the choices will appear as a single-line display at the bottom of the screen, or the full-screen display may be used. When the Full-OSD display system is in use, the complete list of choices will appear on the screen. To activate the Semi-OSD, press the OSD button s once. To activate the Full-OSD, press the OSD button s three times. This will turn the Semi-OSD on and then off. The Full-OSD will appear after the third button press. Once you have determined which, if any, OSD system to use, setup and operation of the multiroom system is simple. 1. Press the Multi button ` to initiate the multiroom system. If the Semi-OSD system is engaged, a message will appear at the bottom of the screen. If the Full-OSD system is engaged, the complete multiroom menu (Figure 9) will be shown on the video display. Press the Set button i within twenty seconds to enter the multiroom menus. MULTI ROOM : OFF ON MULTI INPUT: TAPE CD DVD VIDEO 1 VIDEO 2 VIDEO 3 TUNER MULTI LEVEL: 20 DB MULTIROOM MUTE: OFF ON Figure 9 2. Press the ⁄ or ¤ buttons g to turn the multiroom system on or off, as indicated by the front-panel Information Display message, the Semi-OSD message, or the change in the highlighted video in the Full-OSD screen. Press the Set button i to enter the settings. 3. Press the ¤ Button g to move to the input settings. Press the Set button i to change the input source. Press the ⁄/¤ buttons g to select the desired input. When the input source you wish to send to the remote room location appears on the front-panel Information Display, in the lower screen SemiOSD message, or is highlighted in reverse video in the Full-OSD listing, press the Set button i to enter the selection. 4. Press the ¤ Button g to move to the multilevel setting. Press the Set button i if you wish to change the output level. Within twenty seconds, press the ⁄ or ¤ buttons g to change the output level for the multiroom feed. The volume change will appear as a number in dB increments below the 0dB reference level in the front-panel Information Display, as a lower third SemiOSD message, or as the last line in the Full-OSD status display. 5. Press the Set button i to enter the setting. If no further buttons are pressed within five seconds, the unit will return to normal operation. Multiroom Operation To activate the feed to the remote room, press the Multi button ` on the remote. Next, press the Set button i. Press the ⁄/¤ buttons g to turn the multiroom feed on or off. When the multiroom system is on, the MULTI indicator M will light in the Information Display 35, and the Main Information Display V or OSD will display MUL ROOM ON. Press the Set button i to enter the setting. When the multiroom system is turned on, the previously selected input will be fed to the Multi Out jacks • on the rear panel. The volume will be as set in the previous selection, although it may also be adjusted using an optional volume control in the remote location or on the optional audio power amplifier connected to the Multi Out jacks •. If an optional IR sensor is located in the remote room and connected to the AVR500's Multi IR jack ¤, the multiroom system may be turned on or controlled by simply pointing the AVR500 remote, or an optional programmable remote that includes codes for the AVR500, at the IR sensor. Note that depending on the type of programmable remote used, the code for the AVR's Multi button may not be contained in the preprogrammed code library, and must be "learned" into the remote, if possible. To change the input source for the multiroom feed once it has been turned on, follow the instructions on this page. Once the multiroom system is turned on, it will remain on even if the AVR500 is placed in the Standby mode in the main room by pressing the Power Off Button d or the System Power Control 2 on the front panel. To turn off the multiroom sysytem, even when the AVR is in Standby mode in the main listening room, press the Multi button ` and then the Set button i. Press the ⁄/¤ buttons g so that the MULTI indicator M in the Information Display 35 goes out, and the Main Information Display V or OSD will display MUL ROOM OFF. Press the Set button i to enter the setting and turn the unit off. Even when the AVR is turned off in the main room, the multiroom system may be turned on at any time by pressing the Multi button `. 26 MULTIROOM OPERATION