Harman Kardon HK3270 Owners Manual - Page 12

Remote Control Functions 13 å Main Power On: When the HK3270 is in the Standby mode, as indicated by the Power Indicator 3 glowing amber, press this button to turn the HK3270 on. ∫ Main Power Off: When the HK3270 is turned on, press this button to place it in the Standby mode. Note that in this condition, the unit is still connect to AC Power. ç Source Selectors: Press these buttons to select an input source for the HK3270. ∂ Preset Up/Down: When the tuner is in use, these buttons scroll through the stations that have been programmed into the HK3270's memory. These buttons also control the track Skip Up and Down on compatible Harman Kardon compact disc players/ changers. ≠ Transport Controls: These buttons are used to control Play, Play Forward, Play Reverse, Stop, Pause and Record functions on compatible Harman Kardon compact disc players/ changers and cassette tape decks. ƒ Disc Skip: These buttons do not have any functions when controlling the HK3270, but they operate the Disc Skip functions of compatible Harman Kardon compact disc changers. © Sleep Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the HK3270 will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order: 90 80 70 60 50 min min min min min 40 min 30 min 20 min 10 min OFF ˙ Dimmer: Press this button once to reduce the brightness of the front panel display to half the normal intensity. Press it again to turn the front panel display completely off. When the display is completely off, press the button to return to normal brightness. Tuning: Press these buttons to tune up or down through a selected frequency band. ∆ Master Volume: Press these buttons to raise or lower the HK3270's volume. P•Scan: Press this button to automatically scan through the list of stations that are programmed into the HK3270's tuner memory. When the button is pressed, each preset station will play for five seconds before the next station is selected. Press the button again when the desired station is heard to stop the preset scan. ¬ Mute: Press this button to momentarily silence the HK3270. µ FM Mode: Press this button when the tuner is in use in the FM band to switch to monaural reception if the station is weak and noisy. When the MONO indicator is on, FM reception will be monaural regardless of the strength of the tuned FM station. (See page 15 for more information.) Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. A brief (1⁄2 second) press of the button will manually tune to the next frequency increment, while pressing and holding the button for a longer period will automatically tune to the next station with a signal strong enough for acceptable reception. These buttons will also control Fast Forward and Fast Reverse (or Rewind) for compatible Harman Kardon compact disc players/ changers and cassette tape decks. O Direct : Press this button to select a radio station by entering its frequency using the Numeric Keys R. (See page 15 for more information.) P Numeric Keys: These buttons serve as a ten-button numeric keypad to enter tuner preset positions. Q Auto Preset: When the tuner and FM band have been selected, this button may be used to automatically program the tuner presets for all active stations. To start the auto preset scan, press and hold the button. Note that the MEMO and PRESET indicators will flash. After a few seconds, the tuner will start to "look" for active stations, as shown by increasing frequency numbers in the Information Display. Release the button and note that the tuner will briefly stop at each active station and add a preset number to the memory. If the FM tuner found less the 30 FM stations with acceptable signal strength, the Auto Preset tuning will scan two more cycles or until the remaining vacant preset memory spaces have been filled with those found in the first scan. The scan will stop when all 30 preset memory spaces have been filled or when three scans through the band have been completed. R Secondary Control Cover: This sliding cover normally is in the "up" position so that it hides the secondary controls. To access these controls, place your thumb on the small recessed area at the top center of the control, and gently press the cover down and towards you. S Clear Button: This button is used to clear preset memory information for the HK3270's tuner. (See pages 15-16 for more information on tuner presets.) T Memory: Press this button to open a memory position that stores a preset location for the HK3270's tuner. (See pages 15-16 for more information on tuner presets.)