HP 3600 HP Jetdirect Print Server Administrator's Guide - Page 83

Configuration Messages, HP Jetdirect Configuration/General Information

Get HP 3600 - Color LaserJet Laser Printer PDF manuals and user guides View all HP 3600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Configuration Page Messages HP Jetdirect Configuration/General Information Information in this section provides general HP Jetdirect print server configuration as described in Table 7-1 HP Jetdirect Configuration. For error messages, see Table 7-5 Error Messages. Table 7-1 HP Jetdirect Configuration Message STATUS: MODEL NUMBER: HARDWARE ADDRESS: FIRMWARE VERSION: PORT SELECT: PORT CONFIG: AUTO NEGOTIATION Description Current state of the HP Jetdirect print server. I/O CARD READY: The HP Jetdirect print server has successfully connected to the network and is awaiting data. I/O CARD INITIALIZING: The HP Jetdirect print server is initializing the network protocols. For more information, see the status line for each protocol on the configuration page. I/O CARD NOT READY: There is a problem with the print server or its configuration. An error code and message is displayed if the print server is not ready. For more information, see Table 7-5 Error Messages. The model number of the HP Jetdirect print server (for example, J7973E). The 12-digit hexadecimal network hardware (MAC) address of the HP Jetdirect print server installed in the printer or device. This address is assigned by the manufacturer. The firmware revision number of the HP Jetdirect print server currently installed in the printer. (Ethernet only) Specifies the port on the HP Jetdirect print server that has been detected for use: NONE: The print server is not connected to the network. RJ-45: The RJ-45 network port is connected. Identifies the link configuration of the RJ-45 port on the HP Jetdirect 10/100Base-TX print server: 10BASE-T HALF: 10 Mbps, half-duplex 10BASE-T FULL: 10 Mbps, full-duplex 100TX HALF: 100Mbps, half-duplex 100TX-FULL: 100Mbps, full-duplex UNKNOWN: The print server is in an initialization state. DISCONNECTED: A network connection has not been detected. Check network cables. Identifies whether IEEE 802.3u Auto-negotiation on the HP Jetdirect 10/100TX port is enabled (ON) or disabled (OFF). ON (default): The HP Jetdirect print server will attempt to automatically configure itself onto the network at the proper speed (10 or 100 Mbps) and mode (half or full duplex). Auto-negotiation is enabled after a cold reset. ENWW Configuration Page Messages 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Configuration Page Messages
HP Jetdirect Configuration/General Information
Information in this section provides general HP Jetdirect print server configuration as described in
Table
7-1
HP
Jetdirect
Configuration
. For error messages, see
Table
7-5
Error
Messages
.
Table 7-1
HP Jetdirect Configuration
Message
Description
STATUS:
Current state of the HP Jetdirect print server.
I/O CARD READY: The HP Jetdirect print server has successfully connected to the
network and is awaiting data.
I/O CARD INITIALIZING: The HP Jetdirect print server is initializing the network
protocols. For more information, see the status line for each protocol on the
configuration page.
I/O CARD NOT READY: There is a problem with the print server or its configuration.
An error code and message is displayed if the print server is not ready. For more
information, see
Table
7-5
Error
Messages
.
MODEL NUMBER:
The model number of the HP Jetdirect print server (for example, J7973E).
HARDWARE ADDRESS:
The 12-digit hexadecimal network hardware (MAC) address of the HP Jetdirect print
server installed in the printer or device. This address is assigned by the manufacturer.
FIRMWARE VERSION:
The firmware revision number of the HP Jetdirect print server currently installed in the
printer.
PORT SELECT:
(Ethernet only) Specifies the port on the HP Jetdirect print server that has been
detected for use:
NONE: The print server is not connected to the network.
RJ-45: The RJ-45 network port is connected.
PORT CONFIG:
Identifies the link configuration of the RJ-45 port on the HP Jetdirect 10/100Base-TX
print server:
10BASE-T HALF: 10 Mbps, half-duplex
10BASE-T FULL: 10 Mbps, full-duplex
100TX HALF: 100Mbps, half-duplex
100TX-FULL: 100Mbps, full-duplex
UNKNOWN: The print server is in an initialization state.
DISCONNECTED: A network connection has not been detected. Check network cables.
AUTO NEGOTIATION
Identifies whether IEEE 802.3u Auto-negotiation on the HP Jetdirect 10/100TX port is
enabled (ON) or disabled (OFF).
ON (default): The HP Jetdirect print server will attempt to automatically configure itself
onto the network at the proper speed (10 or 100 Mbps) and mode (half or full duplex).
Auto-negotiation is enabled after a cold reset.
ENWW
Configuration Page Messages
75