HP 3PAR StoreServ 7200 2-node HP 3PAR StoreServ 7000 Storage Site Planning Man - Page 38

A Storage System Installation Checklist

Get HP 3PAR StoreServ 7200 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7200 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

A Storage System Installation Checklist Use this chapter to complete all the requirements before you begin installing the storage system hardware and software. Storage System Hardware Installation Checklist Before you start, verify the environmental conditions, recommended rack space access, and electrical requirements listed in the previous chapters are satisfied and you have all of the following items: • Standard AC power • Host computer with access to software, BIOS, drives, and HP 3PAR OS • Fibre Channel (FC) HBA, FC host cable, and power cord • Other cables • Network access • SP connectivity • Tools • Rail mounting kits • System components or storage system Storage System Software Installation Checklist Before you begin installing the storage system software, make sure you have all of the following items: • All components are installed • The storage system setup is verified, the storage system is powered on, and the LEDs are functioning properly • Either the SP is installed and powered on, and you have assigned an IP addresses, or the VSP is installed and connected, and you have determined the temporary IP address • The SP connection is established Table 20 SP and Storage System Software Installation Checklist HP 3PAR Service Processor SP ID. The SP ID is the 3PAR 7-digit Storage serial number with the prefix SP000. The serial number is located in two places on the SP: on the top front of the server and in a pull-out placard in the front of the server. NOTE: The serial number is located on the back of your HP 3PAR storage system next to the power switch for the node enclosure PCM, and begins with 16 (for example, 1624635). Service Processor Host Name NOTE: During the SP Setup process, the StoreServ must be powered on, connected to the same network subnet as the SP, and non-initialized to allow the SP to verify the StoreServ serial number. Permanent IP address (IPv4 only) Subnet mask Gateway IP address DNS settings: Domain name DNS servers 38 Storage System Installation Checklist

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
A Storage System Installation Checklist
Use this chapter to complete all the requirements before you begin installing the storage system
hardware and software.
Storage System Hardware Installation Checklist
Before you start, verify the environmental conditions, recommended rack space access, and electrical
requirements listed in the previous chapters are satisfied and you have all of the following items:
•
Standard AC power
•
Host computer with access to software, BIOS, drives, and HP 3PAR OS
•
Fibre Channel (FC) HBA, FC host cable, and power cord
•
Other cables
•
Network access
•
SP connectivity
•
Tools
•
Rail mounting kits
•
System components or storage system
Storage System Software Installation Checklist
Before you begin installing the storage system software, make sure you have all of the following
items:
•
All components are installed
•
The storage system setup is verified, the storage system is powered on, and the LEDs are
functioning properly
•
Either the SP is installed and powered on, and you have assigned an IP addresses, or the VSP
is installed and connected, and you have determined the temporary IP address
•
The SP connection is established
Table 20 SP and Storage System Software Installation Checklist
HP 3PAR Service Processor
SP ID. The SP ID is the 3PAR 7-digit Storage serial number with the prefix SP000.
The serial number is located in two places on the SP: on the top front of the server
and in a pull-out placard in the front of the server.
NOTE:
The serial number is located on the back of your HP 3PAR storage system
next to the power switch for the node enclosure PCM, and begins with 16 (for
example, 1624635).
Service Processor Host Name
NOTE:
During the SP Setup process, the StoreServ must be powered on, connected
to the same network subnet as the SP, and non-initialized to allow the SP to verify
the StoreServ serial number.
Permanent IP address (IPv4 only)
Subnet mask
Gateway IP address
DNS settings:
Domain name
DNS servers
38
Storage System Installation Checklist