HP 4400 HP StorageWorks Fabric OS 6.3.2b Release Notes (5697-0777, November 20 - Page 46

Fabric OS 6.3.2a fixes, lists defects closed in the Fabric OS 6.3.2a firmware release

Get HP 4400 PDF manuals and user guides View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

The configdefault command on the switch is not setting default fcmap to 0x0efc00. If configdefault is issued after slotpoweroff or after removing a blade from a slot, configdefault can fail without setting the default value for fcmap, thereby not returning the switch to the default factory state. This affects the 2408 FCoE switch and 10/24 FCoE blade only. Fixed in Fabric OS 6.3.2. Open SSL is updated to address CVD-2009-3555/CERT advisory 120541 (TLS and SSL protocol vulnerability). Fixed in Fabric OS 6.3.2. Tape drives fail when running over FCR with EX_Ports in Open mode. The REC accept payload is incorrect. If host to tape I/O traverses FCR and includes an edge fabric, the tape drives run for a bit and then fail because REC ACC is not processed correctly if the EX_Port is operating in IM3/Open mode. Fixed in Fabric OS 6.3.2. ARP goes away and Neighbor Discovery timeouts occur on routed networks after pulling GE cables during heavy traffic. No end-to-end connection can be established. Tunnel 20 (GE4) failed to recover. Switch had to be reset to recover. Fixed in Fabric OS 6.3.2. With tape encryption, backup to all clear text containers using netbackup in a Multiplex/stream environment results in an encryption SAN switch fault, causing tape flows to halt. Fixed in Fabric OS 6.3.2. Tunnel creation failed with error message Unable to add more FCIP circuits to this tunnel when using VE_Ports 12-15 on DC SAN Backbone director with 2 or more Multiprotocol Extension blades. Not an issue with DC04 SAN director or 1606 extension switch. Workaround prior to upgrade: Use VE_Ports 16-31. Fixed in Fabric OS 6.3.2. Unable to disable default zone from Mi10k in interop fabric in IM2 mode after zone merge failure. Fixed in Fabric OS 6.3.2. Bottleneckmon cannot be enabled on F_Ports with Locked G_Port and Disabled E_Port enabled in portcfg. Workaround prior to upgrade: Disable either or both "Locked G_Port" and "Disabled E_Port" features, but note that this operation is disruptive. Fixed in Fabric OS 6.3.2. Abort in FICON Tape Read emulation if Attention status is received between status and status accept. Workaround prior to upgrade: Disable FICON emulation. Fixed in Fabric OS 6.3.2. Fabric OS 6.3.2a fixes Table 7 lists defects closed in the Fabric OS 6.3.2a firmware release Table 7 Fabric OS 6.3.2a closed defects Closed defect summary Solution In a fabric containing the encryption switch and/or encryption blade, numerous weblinker termination and restart messages can be seen due Fixed in Fabric OS 6.3.2a. to timeouts in handling multiple stats calls in parallel. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Fixed in Fabric OS 6.3.2.
The
configdefault
command on the switch is not setting default
fcmap to 0x0efc00. If
configdefault
is issued after
slotpoweroff
or after removing a blade from a slot,
configdefault
can fail without
setting the default value for fcmap, thereby not returning the switch to
the default factory state. This affects the 2408 FCoE switch and 10/24
FCoE blade only.
Fixed in Fabric OS 6.3.2.
Open SSL is updated to address CVD-2009-3555/CERT advisory
120541 (TLS and SSL protocol vulnerability).
Fixed in Fabric OS 6.3.2.
Tape drives fail when running over FCR with EX_Ports in Open mode.
The REC accept payload is incorrect. If host to tape I/O traverses FCR
and includes an edge fabric, the tape drives run for a bit and then fail
because REC ACC is not processed correctly if the EX_Port is operating
in IM3/Open mode.
Fixed in Fabric OS 6.3.2.
ARP goes away and Neighbor Discovery timeouts occur on routed
networks after pulling GE cables during heavy traffic. No end-to-end
connection can be established. Tunnel 20 (GE4) failed to recover. Switch
had to be reset to recover.
Fixed in Fabric OS 6.3.2.
With tape encryption, backup to all clear text containers using
net-
backup
in a Multiplex/stream environment results in an encryption
SAN switch fault, causing tape flows to halt.
Workaround prior to upgrade:
Use
VE_Ports 16-31.
Fixed in Fabric OS 6.3.2.
Tunnel creation failed with error message
Unable to add more
FCIP circuits to this tunnel
when using VE_Ports 12-15 on
DC SAN Backbone director with 2 or more Multiprotocol Extension
blades. Not an issue with DC04 SAN director or 1606 extension switch.
Fixed in Fabric OS 6.3.2.
Unable to disable default zone from Mi10k in interop fabric in IM2
mode after zone merge failure.
Workaround prior to upgrade:
Disable either or both "Locked
G_Port" and "Disabled E_Port"
features, but note that this operation
is disruptive.
Fixed in Fabric OS 6.3.2.
Bottleneckmon cannot be enabled on F_Ports with
Locked G_Port
and
Disabled E_Port
enabled in
portcfg
.
Workaround prior to upgrade:
Disable FICON emulation.
Fixed in Fabric OS 6.3.2.
Abort in FICON Tape Read emulation if Attention status is received
between status and status accept.
Fabric OS 6.3.2a fixes
Table 7
lists defects closed in the Fabric OS 6.3.2a firmware release
Table 7 Fabric OS 6.3.2a closed defects
Solution
Closed defect summary
Fixed in Fabric OS 6.3.2a.
In a fabric containing the encryption switch and/or encryption blade,
numerous weblinker termination and restart messages can be seen due
to timeouts in handling multiple stats calls in parallel.
46