HP 4400 HP Controller Enclosure Midplane Replacement Instructions (593095-001,
HP 4400 Manual
 |
View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 4400 manual content summary:
- HP 4400 | HP Controller Enclosure Midplane Replacement Instructions (593095-001, - Page 1
hp.com/support/ manuals, and select your product. The information contained herein is subject to change without notice. The only warranties for HP products and services then you might suspect a problem with the midplane board: • Battery module • Fan module • Array controller • Management module • - HP 4400 | HP Controller Enclosure Midplane Replacement Instructions (593095-001, - Page 2
HP P6000 Command View: a. In the navigation pane, select your storage system. b. In the Initialized Storage System Properties window, select the Shut down tab. c. In the Shutdown Options window pull it out a short distance (Figure 3). b. Position one hand under the fan, and with the other hand, pull - HP 4400 | HP Controller Enclosure Midplane Replacement Instructions (593095-001, - Page 3
4 Removing a power supply . 7. Remove the two controllers. a. Move the mounting latch to the right (1, Figure 5). The controller will slightly eject from the enclosure. b. Position one hand under the controller, and with the other hand, pull the controller out of the enclosure (2, Figure 5). Figure - HP 4400 | HP Controller Enclosure Midplane Replacement Instructions (593095-001, - Page 4
Figure 11). Figure 9 Removing baffle . Figure 11 Removing the midplane board . 14. Lift the midplane board out of the enclosure (2, Figure 11). Installing a midplane board 1. Align the mounting holes in the midplane board with the holes in the enclosure chassis and attach the midplane with nine - HP 4400 | HP Controller Enclosure Midplane Replacement Instructions (593095-001, - Page 5
system to check the status of components after the enclosure is powered on. After replacing the midplane board, check the status of all components with HP P6000 Command View and the indicators of all installed components for proper operation. Page 5
-
1 -
2 -
3 -
4 -
5
 |
 |
HP Controller Enclosure
Midplane Replacement
Instructions
© Copyright 2009 Hewlett-Packard Development Company, L.P.
Second edition: May 2011
The information in this document is subject to change without notice.
Printed in Puerto Rico
www.hp.com
*593095-001*
About this document
For the latest documentation, go to
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/
man
uals
, and select your product.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the
express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.
WARRANTY STATEMENT:
To obtain a copy of the warranty for this product, see the warranty
information website:
h
t
tp://w
w
w
.hp
.co
m/go/s
t
o
r
age
w
ar
r
an
t
y
Before you begin
Observe the following precaution when replacing the controller midplane.
CAUTION:
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection. Refer to the documentation that shipped
with your system for additional information.
Your controller enclosure model may vary slightly from what is illustrated
in this document.
Verifying component failure
There are few active parts on the midplane board that can fail. If you
receive error messages, or see erroneous LED indications on the following
components that you know are good, then you might suspect a problem
with the midplane board:
•
Battery module
•
Fan module
•
Array controller
•
Management module
•
Power supply module
•
Riser assembly
•
LED display
•
Power UID
Page 1