HP 6100 HP StorageWorks Controller Blower Replacement Instructions (5697-6720,

HP 6100 Manual

Get HP 6100 PDF manuals and user guides View all HP 6100 manuals
Add to My Manuals
Save this manual to your list of manuals

HP 6100 manual content summary:

  • 1
  • 2
HP StorageWorks
Controller blower replacement
instructions
These instructions apply to EVA 4x00/6x00/8x00
products. The part may also be used in other HP
products. See the documentation for your speci
fi
c
product for detailed replacement instructions.
© Copyright 2005 Hewlett-Packard Development Company, L.P.
Fourth edition June 2007
The information in this document is subject to change without
notice.
Printed in the Puerto Rico
www.hp.com
*5697-6720*
About this document
This document describes the procedure for replacing the controller
blower.
Warranty information
If the product in which this part is being replaced is still under
HP warranty, then the replacement part(s) referred to in these
Replacement Instructions is provided under the terms and conditions
of the Hewlett-Packard Company Limited Warranty for that
product.
A copy of this Limited Warranty may be viewed at:
h
t
t
p
:
/
/
h
1
8
0
0
6
.
w
w
w
1
.
h
p
.
c
o
m
/
p
r
o
d
u
c
t
s
/
s
t
o
r
a
g
e
w
o
r
k
s
/
w
a
r
r
a
n
t
y
.
h
t
m
l
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under
HP's express limited warranty statement, which may be viewed at:
h
t
t
p
:
/
/
c
u
s
t
o
m
e
r
o
p
s
.
c
o
r
p
.
h
p
.
c
o
m
/
1
s
w
/
p
d
m
_
o
m
/
w
a
r
r
a
n
t
y
_
s
u
p
p
o
r
t
/
p
o
l
i
c
i
e
s
/
2
3
3
0
1
0
0
.
d
o
c
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The only warranty for this replacement product is as noted above.
Nothing in these replacement instructions should be construed as
constituting an additional warranty. The information provided in these
replacement instructions is provided "AS IS" and HP is not liable for
technical or editorial errors or omissions contained herein.
Before you begin
Observe the following precautions when replacing a blower:
•
Removing a blower signi
fi
cantly changes the air
fl
ow within the
enclosure. Both blowers must be installed for the enclosure to cool
properly. If a blowers fails, leave it in the enclosure until a new
blower is available to install.
•
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection.
•
Have a copy of the product user guide available for reference. You
can download a copy of the user guide from the product support
page on the HP website.
Verifying component failure
Before replacing a blower, use the following methods to verify the
component failure:
CAUTION:
If HP Command View EVA does not present a status consistent with
the blower status indicators, or if either HP Command View EVA or
your system monitoring tool indicates multiple hardware failures,
contact HP support for assistance (
h
t
t
p
:
/
/
w
w
w
.
h
p
.
c
o
m
/
s
u
p
p
o
r
t
).
•
Analyze any failure messages received.
•
Check the controller blower status using HP Command View EVA:
1.
In the Navigation pane, select
Storage system > Hardware >
Rack > Controller enclosure > Controller
.
2.
In the Content pane, select the
Enclosure
tab. The status is
displayed in the
Cooling System
fi
eld. The status should be
Failed
.
Page 1