HP 7310 Network Guide - Page 24

Configuration definitions, General network settings - all in one manual

Get HP 7310 - Officejet All-in-One Color Inkjet PDF manuals and user guides View all HP 7310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

a Configuration page definitions This appendix explains the items that appear on the network configuration page. General network settings The following table describes the general network settings shown on the network configuration page. Parameter Network Status Description Status of the HP all-in-one: ● Ready: the HP all-in-one is ready to receive or transmit data. ● Offline: the HP all-in-one is offline. Active Connection Type Network mode of the HP all-in-one: ● Wired: the HP all-in-one is connected by Ethernet cable to an IEEE 802.3 network. ● Wireless: the HP all-in-one is connected wirelessly to an IEEE 802.11b or g network. ● None: Both network connection types are disabled. Note Only one connection type can be active at a time. URL The web or IP address of the Embedded Web Server. Hardware Address (MAC) Firmware Revision Hostname IP Address Note You will need to know this URL when you try to access the Embedded Web Server. The Media Access Control (MAC) address that uniquely identifies the HP all-in-one. This is a unique 12-digit identification number assigned to networking hardware for identification. No two pieces of hardware have the same MAC address. Note Some Internet service providers (ISPs) require that you register the MAC address of the Network Card or LAN Adapter that was connected to your cable or DSL modem during installation. The internal networking component and device firmware revision code separated by a hyphen. Note If you call in for support, depending on the problem, you might be asked to provide the firmware revision code. The TCP/IP name assigned by the install software to the device. By default, this is the letters HP followed by the last 6 digits of the MAC address. This address uniquely identifies the device on the network. IP addresses are assigned dynamically through DHCP or AutoIP. You can also set up a static IP address, though this is not recommended. Note Manually assigning an invalid IP address during install will prevent your network components from seeing the HP all-in-one. HP all-in-one Network Guide 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
a
Configuration page definitions
This appendix explains the items that appear on the network configuration page.
General network settings
The following table describes the general network settings shown on the network configuration
page.
Parameter
Description
Network Status
Status of the HP all-in-one:
●
Ready:
the HP all-in-one is ready to receive or transmit data.
●
Offline:
the HP all-in-one is offline.
Active
Connection Type
Network mode of the HP all-in-one:
●
Wired:
the HP all-in-one is connected by Ethernet cable to an IEEE
802.3 network.
●
Wireless:
the HP all-in-one is connected wirelessly to an IEEE 802.11b
or g network.
●
None:
Both network connection types are disabled.
Note
Only one connection type can be active at a time.
URL
The web or IP address of the Embedded Web Server.
Note
You will need to know this URL when you try to access the
Embedded Web Server.
Hardware
Address (MAC)
The Media Access Control (MAC) address that uniquely identifies the
HP all-in-one. This is a unique 12-digit identification number assigned to
networking hardware for identification. No two pieces of hardware have the
same MAC address.
Note
Some Internet service providers (ISPs) require that you register the
MAC address of the Network Card or LAN Adapter that was
connected to your cable or DSL modem during installation.
Firmware
Revision
The internal networking component and device firmware revision code
separated by a hyphen.
Note
If you call in for support, depending on the problem, you might be
asked to provide the firmware revision code.
Hostname
The TCP/IP name assigned by the install software to the device. By default,
this is the letters HP followed by the last 6 digits of the MAC address.
IP Address
This address uniquely identifies the device on the network. IP addresses are
assigned dynamically through DHCP or AutoIP. You can also set up a static
IP address, though this is not recommended.
Note
Manually assigning an invalid IP address during install will prevent
your network components from seeing the HP all-in-one.
HP all-in-one Network Guide
21