HP AD510A HP StorageWorks MSA1500 cs Fibre Channel I/O Module Replacement Inst
HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive Manual
 |
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP AD510A manual content summary:
- HP AD510A | HP StorageWorks MSA1500 cs Fibre Channel I/O Module Replacement Inst - Page 1
2-GB LED is flashing amber 3. 1 2 3 If the product in which this part is being replaced is still under HP warranty, then the replacement part(s) referred to in these Replacement Instructions is provided under the terms and conditions of the Hewlett-Packard Company Limited Warranty for that product - HP AD510A | HP StorageWorks MSA1500 cs Fibre Channel I/O Module Replacement Inst - Page 2
cable will either damage the cable or cause performance problems, including intermittent difficulties accessing the storage. ■ Whenever green. Returning the failed component Please follow the return instructions provided in the replacement component package. Additional information For additional
-
1 -
2
 |
 |
hp
StorageWorks
MSA1500 cs Fibre
Channel I/O Module
MSA1500 cs Fibre Channel I/O Module Replacement
Instructions
First Edition (April 2004)
Part Number: 361697-001
If the product in which this part is being replaced is still under HP
warranty, then the replacement part(s) referred to in these Replacement
Instructions is provided under the terms and conditions of the
Hewlett-Packard Company Limited Warranty for that product.
A copy of
this Limited Warranty may be viewed at:
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under HP’s
express limited warranty statement, which may be viewed at:
2330100.doc
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The information contained on these replacement instructions is subject to
change without notice.
The only warranty for this replacement product is
as noted above.
Nothing in these replacement instructions should be
construed as constituting an additional warranty.
The information
provided in these replacement instructions is provided “AS IS” and HP is
not liable for technical or editorial errors or omissions contained herein.
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Please note that this document is protected by federal copyright law and
that no part of this document may be copied, reproduced or translated
without the prior written consent of Hewlett-Packard Development
Company, L.P.
Printed in Singapore.
Replacement
Instructions
These instructions apply to the
MSA1500 cs product family. The part
may also be used in other HP products.
Please refer to documentation for your
specific product for detailed replacement
instructions.
361697- 001
About this document
This document details the procedures for replacing a failed MSA1500 cs Fibre
Channel I/O module in HP StorageWorks Modular Smart Array (MSA) storage
systems.
Verifying component failure
Before replacing the Fibre Channel I/O module, use the following methods to
verify the component failure.
■
Check the controller LCD for one of the error messages listed in Table 1.
■
The status LED on the rear of the Fibre Channel I/O module is not
illuminated or is flashing amber
1
.
■
The 1-GB LED is flashing amber
2
.
■
The 2-GB LED is flashing amber
3
.
Figure 1:
System fault indicator
Before you begin
Read the following cautions and information before beginning removal and
replacement procedures.
Laser precautions
WARNING:
To reduce the risk of injury from laser radiation or
damage to the equipment, observe the following precautions:
■
Do not open any panels, operate controls, make adjustments,
or perform procedures to a laser device other than those
specified herein.
■
Do not stare into the laser beam when panels are open.
Caution:
Be sure the replacement part is available before
removing the failed component. Removing a component impacts
cooling within the enclosure.
Caution:
Parts can be damaged by electrostatic discharge. Use
proper anti-static protection. Refer to the documentation that
shipped with your system for additional information.
Caution:
It is important to follow these instructions when replacing
components in the MSA. If the procedure is done improperly, it is
possible to lose data or damage equipment.
Note:
Before replacing a controller it is important to stop all system access
(e.g. application, system I/O or RAW device file path/s) to the device.
Table 1:
LCD Error Messages
No.
Message
515
FIBRE DEVICE HARDWARE FAILURE
516
FIBRE SUBSYSTEM LINK FAILURE
1
2
3