HP AE326A HP StorageWorks 1500/1510i Modular Smart Array chassis replacement i
HP AE326A - StorageWorks Modular Smart Array 1500 SAN SATA Starter Manual
UPC - 882780184954
View all HP AE326A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP AE326A manual content summary:
- HP AE326A | HP StorageWorks 1500/1510i Modular Smart Array chassis replacement i - Page 1
HP StorageWorks 1500/1510i Modular Smart Array chassis replacement instructions © Copyright 2004-2006 Hewlett-Packard Development Company, L.P. Second edition (December 2006) The information in this document is subject to change without notice. Printed in Singapore. www.hp of an MSA1500. If you Parts - HP AE326A | HP StorageWorks 1500/1510i Modular Smart Array chassis replacement i - Page 2
carefully and then disconnect all of the cables. CAUTION: If replacing the MSA1500 chassis, use caution when handling the Fibre Channel cables: • Touching Fibre Channel cable will either damage the cable or cause performance problems, including intermittent difficulties accessing the storage. • When - HP AE326A | HP StorageWorks 1500/1510i Modular Smart Array chassis replacement i - Page 3
the original chassis may automatically be transferred to the replacement chassis. For continued service and support from HP authorized service personnel, the serial number of the original chassis must also be physically recorded on the label of the replacement chassis. The product label is located - HP AE326A | HP StorageWorks 1500/1510i Modular Smart Array chassis replacement i - Page 4
CHASSIS DETECTED CHASSIS SERIAL NUMBER FLASHED UPDATED IMPORTANT: If these messages are displayed, the MSA1500/1510i will automatically restart. of the hard drives does not match. The original configuration was changed or startup procedures were followed incorrectly. Power off the MSA1500/1510i, - HP AE326A | HP StorageWorks 1500/1510i Modular Smart Array chassis replacement i - Page 5
five business days. The defective part must be returned with the associated documentation in the provided shipping material. Failure to return the defective part may result in HP billing you for the replacement. For details, follow the return instructions shipped with the replacement chassis. Page
HP StorageWorks
1500/1510i Modular Smart
Array chassis replacement
instructions
© Copyright 2004–2006 Hewlett-Packard Development Company,
L.P.
Second edition (December 2006)
The information in this document is subject to change without
notice.
Printed in Singapore.
www.hp.com
364862-002
About this document
This document details procedures for replacing a failed MSA1500
or MSA1510i chassis. When replacing a chassis, components are
removed from the failed chassis and then installed in the replacement.
Components that are moved include the following:
•
Fibre Channel (or Ethernet) I/O modules
•
Fan modules
•
SCSI I/O modules
•
Power supply modules
•
Controllers
•
Blanks
NOTE:
The MSA1500 connects to the SAN with a Fibre Channel I/O
module and the MSA1510i connects to the network with a 2–Port
Ethernet I/O module. Illustrations in this document show the Fibre
Channel I/O module of an MSA1500. If you are replacing an
MSA1510i chassis, your module will look different.
Before you begin
Read the following cautions and notices before replacing the chassis.
CAUTION:
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection. For additional information, see the
documentation that shipped with your system.
CAUTION:
Be sure to follow these instructions carefully. If the procedures are
done improperly or out of sequence, it is possible to lose data
or damage equipment.
IMPORTANT:
Schedule a maintenance window of approximately
60
minutes to
complete this procedure.
IMPORTANT:
Before beginning these procedures, verify that there is a known,
good backup of the system. Backup all volumes and, for the
MSA1510i, record the iSCSI and Management settings.
TIP:
Before beginning these procedures, label all cables. This ensures
that they are reconnected correctly.
Page 1