HP All-in-One 200-5251 Upgrading and Servicing Guide
HP All-in-One 200-5251 Manual
 |
View all HP All-in-One 200-5251 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP All-in-One 200-5251 manual content summary:
- HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 1
Printed in Upgrading and Servicing Guide Removing the Stand for Wall Mounting ...........2 Before You Begin 2 Computer Computer Preparation 18 Removing the Memory 19 Installing a New Memory Card 20 Troubleshooting 21 Removing and Replacing a Computer Stand ..24 Before You Begin 24 - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 2
ii 599977-001 - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 3
Removing the Stand for Wall Mounting - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 4
Removing the Stand for Wall Mounting 5-10 minutes The computer can be mounted on a wall by attaching a wall-mounting device (sold separately) to the back of the computer. The four mounting holes on the back of the computer are compliant with the VESA 100 mm spacing standard for mounting compatible - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 5
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Use a screwdriver to remove the four screws holding the stand. Removing the Stand 6 Remove the back cover above the stand at the back of the computer. Insert a flathead - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 6
12 Use a flathead screwdriver to remove the plastic tabs covering the two screw holes below the back cover. 15 Follow the wall-mounting hardware manufacturer's instructions on how to wall-mount the computer. 13 Replace the back cover on to the computer. 4 599977-001 - Removing the Stand for Wall - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 7
Removing and Replacing a CD/DVD Drive - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 8
Removing and Replacing a CD/DVD Drive 10 - 15 minutes Before You Begin Observe the following requirements before removing and replacing the hard disk drive. Tools Needed Flathead screwdriver Phillips screwdriver #1 CAUTION: Static electricity can damage the electronic components inside the - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 9
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Slide the side cover off the computer in the direction indicated by the arrow. Removing the CD/DVD Drive 6 Remove the back cover above the stand at the back of the computer. - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 10
11 Insert a finger, or a screwdriver, in the slot and push the CD/DVD drive out. Installing a New CD/DVD Drive NOTE: The replacement CD/DVD drive may not look exactly the same as the original drive due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 11
4 Replace the side cover. 8 Reconnect all the cables. 5 Replace the back cover above the stand. 6 Place the computer in an upright position. 7 Plug in the power cord. 599977-001 - Removing and Replacing a CD/DVD Drive 9 - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 12
10 599977-001 - Removing and Replacing a CD/DVD Drive - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 13
Removing and Replacing a Hard Disk Drive - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 14
Removing and Replacing a Hard Disk Drive 10 - 15 minutes Before You Begin Observe the following requirements before removing and replacing the hard disk drive. IMPORTANT: A hard disk drive is extremely sensitive to shock impact. Do not bang or drop it. Do not touch the circuit board. Static - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 15
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Slide the side cover off the computer in the direction indicated by the arrow. Removing the Hard Disk Drive 6 Remove the back cover above the stand at the back of the - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 16
11 Grasp the metal handle on the hard disk drive cage to slide the cage in the direction indicated by the arrow on the cage. 14 Slide the hard disk drive out of the cage. 12 Lift out the hard disk drive. 13 To remove the hard disk drive from the cage, unscrew the four screws on the cage using a - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 17
2 Slide the replacement hard disk drive into the cage. 5 Tighten the screw. 3 Replace the four screws on the hard disk drive cage. 6 Replace the side cover. 4 Grasp the cage by the handle and slide the hard disk drive back into the hard disk drive bay until it stops. 7 Replace the back cover - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 18
9 Plug the power cord. 10 Reconnect all the cables. 16 599977-001 - Removing and Replacing a Hard Disk Drive - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 19
Upgrading or Replacing Memory - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 20
Upgrading or Replacing Memory 10 - 15 minutes Before You Begin Observe the following requirements before removing and replacing memory cards. Tools Needed Flathead screwdriver CAUTION: Static electricity can damage the electronic components inside the computer. Discharge static electricity by - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 21
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Slide the cover off the compute in the direction indicated by the arrow. Removing the Memory 6 Remove the back cover above the stand at the back of the computer. Insert a - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 22
Installing a New Memory Card NOTE: The replacement memory card may not look exactly the same as the original drive due to different manufacturers or models. Hewlett-Packard always provides quality parts that meet or exceed your original computer specifications. 1 Orient the new memory card so that - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 23
8 Reconnect all the cables. 9 Return the computer to the upright position and turn on the computer. Troubleshooting If the computer displays a memory error after you have turned it back on, check the following: Turn the computer off and unplug the power cord, - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 24
22 599977-001 - Upgrading or Replacing Memory - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 25
Removing and Replacing a Computer Stand - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 26
Removing and Replacing a Computer Stand 5-10 minutes Before You Begin Observe the following requirements before removing and replacing the computer stand. Tools Needed Flathead screwdriver Phillips screwdriver #2 CAUTION: Static electricity can damage the electronic components inside the - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 27
5 Lay the computer down on a flat surface, covered with a soft cloth to protect the screen from scratches or other damage. 8 Use a screwdriver to remove the four screws holding the stand. Removing the Stand 6 Remove the back cover above the stand at the back of the computer. Insert a flathead - HP All-in-One 200-5251 | Upgrading and Servicing Guide - Page 28
Installing a New Stand 1 Align the slot in the new stand assembly with the tab on the computer. Slide the stand in until it aligns with the four screw holes. 4 Place the computer in an upright position. 5 Plug in the power cord. 2 Replace the four screws. 6 Reconnect all the cables. 3 Replace
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
 |
 |
599977-001
i
Printed in
Upgrading and Servicing Guide
Removing the Stand for Wall Mounting
...........
2
Before You Begin
.................................................
2
Computer Preparation
..........................................
2
Removing the Stand
.............................................
3
Removing and Replacing a CD/DVD Drive
.......
6
Before You Begin
.................................................
6
Computer Preparation
..........................................
6
Removing the CD/DVD Drive
................................
7
Installing a New CD/DVD Drive
............................
8
Removing and Replacing a Hard Disk Drive ..12
Before You Begin
...............................................
12
Computer Preparation
........................................
12
Removing the Hard Disk Drive
.............................
13
Installing a New Hard Disk Drive
........................
14
Upgrading or Replacing Memory
..................
18
Before You Begin
...............................................
18
Computer Preparation
........................................
18
Removing the Memory
........................................
19
Installing a New Memory Card
............................
20
Troubleshooting
.................................................
21
Removing and Replacing a Computer Stand ..24
Before You Begin
...............................................
24
Computer Preparation
........................................
24
Removing the Stand
...........................................
25
Installing a New Stand
.......................................
26