HP Brocade 8/12c HP StorageWorks B-series Data Center Fabric Manager Professio - Page 21

Symptom-References to IOD Delay configuration, Open Fabric Mode.

Get HP Brocade 8/12c PDF manuals and user guides View all HP Brocade 8/12c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Closed defect summary Solution References to IOD Delay dialog are found in several places in online help. Symptom-References to IOD Delay configuration dialog are found in several places in the online help even though this dialog does not exist in the application. Fixed in DCFM 10.1.0 Help for Event Notification needs to be modified (both in the online help and PDF document). Symptom-User will get incorrect information regarding the Event Notification feature from online help and the PDF document. Fixed in DCFM 10.1.0 On closing and re-launching the Audit logs table in DCFM, some of the events that were present disappear. Symptom-When the customer close and relaunches the Audit logs table, some of the events that were present earlier will not appear. Fixed in DCFM 10.1.0 Workaround-The user must rely on the Master log for all the lost events. The online help for Call Home needs to be modified. Fixed in DCFM 10.1.0 Symptom-User will get wrong information regarding Call Home. Deleting LSAN zones from the LSAN zoning scope does not work for a fabric that is in the "McDATA Open Fabric Mode". Symptom-The customer see an error message which says "Unable to activate the zones in the McDATA Open Fabric Mode". As a result, the customer will not be able to delete the LSAN zones from the fabric. Fixed in DCFM 10.1.0 Workaround-Manually delete all the LSAN zones from the fabric through EOS. Online help for Set End to End Monitor dialog does not mention the Refresh button in the dialog. Symptom-The user does not get any information in the online help content regarding the Refresh button in the Set End To End monitors dialog. Fixed in DCFM 10.1.0 If a user deletes all the tunnels and creates new nl tunnels, the older tunnel is shown in the switch nl properties of DCFM. Symptom-Customer can see the older tunnel shown in the FCIP tunnels tab of switch properties. If the user needs to check the FCIP tunnel ID drop-down, that tunnel is not shown. Fixed in DCFM 10.1.0 Workaround-Delete the tunnel again from Switch properties where the tunnel is created. The Call Home section in the PDF document needs to be modified. Symptom-The user will not get proper information from the PDF document. Fixed in DCFM 10.1.0 HP StorageWorks B-series Data Center Fabric Manager Professional 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Solution
Closed defect summary
Fixed in DCFM 10.1.0
References to IOD Delay dialog are found in several
places in online help.
Symptom—References to IOD Delay configuration
dialog are found in several places in the online help
even though this dialog does not exist in the
application.
Fixed in DCFM 10.1.0
Help for Event Notification needs to be modified (both
in the online help and PDF document).
Symptom—User will get incorrect information
regarding the Event Notification feature from online
help and the PDF document.
Fixed in DCFM 10.1.0
Workaround—The user must rely on the Master log
for all the lost events.
On closing and re-launching the
Audit
logs table in
DCFM, some of the events that were present disap-
pear.
Symptom—When the customer close and relaunches
the Audit logs table, some of the events that were
present earlier will not appear.
Fixed in DCFM 10.1.0
The online help for Call Home needs to be modified.
Symptom—User will get wrong information regarding
Call Home.
Fixed in DCFM 10.1.0
Workaround—Manually delete all the LSAN zones
from the fabric through EOS.
Deleting LSAN zones from the LSAN zoning scope
does not work for a fabric that is in the “McDATA
Open Fabric Mode”.
Symptom—The customer see an error message which
says "Unable to activate the zones in the McDATA
Open Fabric Mode". As a result, the customer will not
be able to delete the LSAN zones from the fabric.
Fixed in DCFM 10.1.0
Online help for Set End to End Monitor dialog does
not mention the Refresh button in the dialog.
Symptom—The user does not get any information in
the online help content regarding the Refresh button
in the Set End To End monitors dialog.
Fixed in DCFM 10.1.0
Workaround—Delete the tunnel again from Switch
properties where the tunnel is created.
If a user deletes all the tunnels and creates new
nl
tunnels, the older tunnel is shown in the switch
nl
properties of DCFM.
Symptom—Customer can see the older tunnel shown
in the FCIP tunnels tab of switch properties. If the user
needs to check the FCIP tunnel ID drop-down, that
tunnel is not shown.
Fixed in DCFM 10.1.0
The Call Home section in the PDF document needs to
be modified.
Symptom—The user will not get proper information
from the PDF document.
HP StorageWorks B-series Data Center Fabric Manager Professional
21