HP Cisco MDS 9020 Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Rel - Page 34

show logging onboard, Workaround, Symptom, snmp-server enable trap

Page 34 highlights

Caveats Send documentation comments to [email protected] switch# show system reset-reason --- reset reason for Supervisor-module 1 (from Supervisor in slot 1) --1) No time Reason: Unknown Service: Version: 3.1(2) or switch# show system reset-reason ----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) --1) At 203437 usecs after Fri Jul 4 18:32:02 2008 Reason: Watchdog Timeout Service: Version: 3.1(2) Entering the show logging onboard command will contain a card uptime record with an uptime of 497 days. Thu Sep 25 19:09:33 2008: Card Uptime Record Uptime: 42946218, 497 days 1 hour(s) 30 minute(s) 18 second(s) Reset Reason: Unknown (0) Card Mode Runtime Workaround: This issue is resolved. • CSCso06144 Symptom: Under certain rare circumstances, where there are excessive packet drops in the fabric for a given I/O, port software failure (or in other words, SME engine reset) may be seen due to a race condition between the host side and target side error handling of the exchange. This issue has been observed in stress test scenarios where there are packet drops in the host side and lot of target check conditions for the same I/O. Workaround: This issue is resolved. • CSCso85603 Symptom: CPP SME may crash when the port software failure coincides with the forwarding of a SCSI error response from the target. Workaround: This issue is resolved. • CSCsq20470 Symptom: If you have more than 7 SME modules in a switch, Fabric Manager Web Client hangs when the cluster summary page is selected. Workaround: This issue is resolved. • CSCsq23079 Symptom: The snmp-server enable trap CLI command does not support enabling or disabling of traps from the CISCO-IPSEC-PROVISIONING-MIB. Workaround: This issue is resolved. • CSCsq23098 Symptom: The snmp-server enable trap CLI command does not support enabling or disabling of traps from the CISCO-IMAGE-UPGRADE-MIB. Workaround: This issue is resolved. Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(2) 34 OL-14116-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58

Send documentation comments to [email protected]
34
Cisco MDS 9000 Family Release Notes for Cisco MDS SAN-OS Release 3.3(2)
OL-14116-10
Caveats
switch#
show system reset-reason
--- reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---
1) No time
Reason: Unknown
Service:
Version: 3.1(2)
or
switch#
show system reset-reason
----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---
1) At 203437 usecs after Fri Jul 4 18:32:02 2008
Reason: Watchdog Timeout
Service:
Version: 3.1(2)
Entering the
show logging onboard
command will contain a card uptime record with an uptime of
497 days.
Thu Sep 25 19:09:33 2008: Card Uptime Record
----------------------------------------------
Uptime: 42946218, 497 days 1 hour(s) 30 minute(s) 18 second(s)
Reset Reason: Unknown (0)
Card Mode
..........................
: Runtime
Workaround
: This issue is resolved.
CSCso06144
Symptom
: Under certain rare circumstances, where there are excessive packet drops in the fabric
for a given I/O, port software failure (or in other words, SME engine reset) may be seen due to a
race condition between the host side and target side error handling of the exchange. This issue has
been observed in stress test scenarios where there are packet drops in the host side and lot of target
check conditions for the same I/O.
Workaround
: This issue is resolved.
CSCso85603
Symptom
: CPP SME may crash when the port software failure coincides with the forwarding of a
SCSI error response from the target.
Workaround
: This issue is resolved.
CSCsq20470
Symptom
: If you have more than 7 SME modules in a switch, Fabric Manager Web Client hangs
when the cluster summary page is selected.
Workaround
: This issue is resolved.
CSCsq23079
Symptom
: The
snmp-server enable trap
CLI command does not support enabling or disabling of
traps from the CISCO-IPSEC-PROVISIONING-MIB.
Workaround
: This issue is resolved.
CSCsq23098
Symptom
: The
snmp-server enable trap
CLI command does not support enabling or disabling of
traps from the CISCO-IMAGE-UPGRADE-MIB.
Workaround
: This issue is resolved.