HP DL320 HP ProLiant Servers Troubleshooting Guide - Page 93
Description, Action, Actio
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 93 highlights
Accelerator Status: Warranty Alert Description: Catastrophic problem exists with array accelerator board. Refer to other messages on Diagnostics screen for exact meaning of this message. Action: Replace the array accelerator board. Adapter/NVRAM ID Mismatch Description: EISA NVRAM has an ID for a different controller from the one physically present in the slot. Action: Run the server setup utility. Array Accelerator Battery Pack X not Fully Charged Description: Battery is not fully charged. Action: If 75% of the batteries present are fully charged, the array accelerator is fully operational. If more than 75% of the batteries are not fully charged, allow 36 hours to recharge them. Array Accelerator Battery Pack X Below Reference Voltage (Recharging) Description: Battery pack on the array accelerator is below the required voltage levels. Action: Replace the array accelerator board if the batteries do not recharge within 36 powered-on hours. Board in Use by Expand Operation Description: Array accelerator memory is in use by a capacity expansion or RAID migration. Action: The array accelerator is automatically re-enabled for caching when the capacity expansion or RAID operation completes. Board not Attached Description: An array controller is configured for use with array accelerator board, but one is not connected. Action: Connect array accelerator board to array controller. Cache Has Been Disabled Because ADG Enabler Dongle is Broken or Missing Description: The cache has been disabled because RAID ADG volume is configured but the ADG Enabler Dongle is broken or missing. Action: Check the ADG Enabler Dongle. Replace if needed. Cache Has Been Disabled; Likely Caused By a Loose Pin on One of the RAM Chips Description: Cache has been disabled due to a large number of ECC errors detected while testing the cache during POST. This is probably caused by a loose pin on one of the RAM chips. Action: Try reseating the cache to the controller. If that does not work, replace the cache. Error messages 93
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188