HP DL785 3-7U Quick Deploy Rail System Installation Instructions
HP DL785 - ProLiant - G5 Manual
UPC - 883585262809
View all HP DL785 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP DL785 manual content summary:
- HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 1
System Installation Instructions for HP products Overview This rack hardware kit supports a variety of 3-7U HP products in round-, square-, or threaded-hole racks. Use the legend to identify installation steps appropriate to the type of rack. IMPORTANT: If you are shipping the server installed in - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 2
weight The anti-tip stabilizers provide stability and support when equipment is installed, removed or accessed are optional on either end of the row. HP recommends that stabilizer option kits be used when one shipping the server installed in a rack, see the additional instructions located in " - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 3
IMPORTANT: If you are installing the server in a shallow rack [i.e., less than 72.39 cm (28.5 in)], see the additional instructions located in "Preparing the rails for shallow rack installation" before proceeding. - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 4
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is adequately stabilized before sliding the server into the rails. WARNING: To reduce the risk of personal injury or equipment damage, do one of the following: • Use two or more people to - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 5
IMPORTANT: If you need to hinge the cable management arm on the rear right-hand side of the rack, see the instructions located in "Converting the cable management arm swing" and perform the steps to convert the arm to a right-hand swing before installing the arm on the rack. After conversion, mirror - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 6
arm. NOTE: When properly installed, the cable management arm is attached to the server and the rack rail. The installation is complete. If the rack installation is to be shipped with product(s) installed, perform the steps in "Preparing the product for rack relocation or integrated shipping." - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 7
IMPORTANT: When converting the cable arm, always be sure to orient the arm with the cable trough facing upward. The cable management arm is ready for installation on the rack. Preparing the rails for integrated shipping in a rack IMPORTANT: You must provide screws to secure the slide mounting - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 8
IMPORTANT: You will need kit 371482-B21 to prepare a round-hole rack for integrated shipping. NOTE: Use the integrated shipping hardware included with this kit to prepare a square-hole rack for integrated shipping. - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 9
Preparing the product for rack relocation or integrated shipping Return to step 1 in "Installing the product in a rack." To service or remove the product from the rack, reverse the procedures in this section: 1. Remove the rear slide locking screw and the front rail locking screws. - HP DL785 | 3-7U Quick Deploy Rail System Installation Instructions - Page 10
Preparing the rails for shallow rack installation Return to step 2 in "Installing the product in a rack."
HP 3-7U Quick Deploy
Rail System
Installation Instructions
for HP products
© Copyright 2005-2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
June 2006 (Third Edition)
Part Number 378950-003
Overview
This rack hardware kit supports a variety of 3-7U HP products
in round-, square-, or threaded-hole racks. Use the legend to
identify installation steps appropriate to the type of rack.
IMPORTANT:
If you are shipping the server installed
in a rack, see the additional instructions located in
"Preparing the product for rack relocation or
integrated shipping" before proceeding.
Hardware kit contents
In addition to the supplied items, you may need:
•
Screws that fit a threaded-hole rack
•
The appropriate screwdriver for the screws
•
Kit 371482-B21 for integrated shipping a
round-hole rack
Rack warnings
WARNING:
To reduce the risk of personal
injury or damage to the equipment,
be sure that:
•
The leveling jacks are extended to
the floor.