HP DesignJet T700 Regulatory Safety and Environmental Notices User Guide - Page 25

Power supply and power cord set requirements, Power supply class I grounding requirements

Get HP DesignJet T700 PDF manuals and user guides View all HP DesignJet T700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Each laser product complies with US FDA Regulations of 21 CFR 1040.10 and 1040.11 or complies with those regulations except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 or Laser Notice No. 56, dated May 8, 2019. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation: ● Do not try to open the module enclosure. There are no user-serviceable components inside. ● Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. ● Allow only HP Authorized Service technicians to repair the unit. Power supply and power cord set requirements Power supply class I grounding requirements For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide adequate fault protection. Only use the power cord supplied with this product or an HP Inc. authorized replacement. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica que possua aterramento (três pinos), conforme a norma nbr abnt 5410,visando a segurança dos usuários contra choques elétricos. Denmark Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. Finland Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan. Norway Apparatet må tilkoples jordet stikkontakt. Sweden Apparaten skall anslutas till jordat uttag. Power supply requirements The power supplies on some products have external power switches. The voltage select switch feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts AC. Power supplies on those products that do not have external power switches are equipped with internal circuits that sense the incoming voltage and automatically switch to the proper voltage. WARNING! To reduce potential safety issues, only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used with the computer. Power supply and power cord set requirements 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Each laser product complies with US FDA Regulations of 21 CFR 1040.10 and 1040.11 or complies with those
regulations except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 or Laser Notice No. 56,
dated May 8, 2019.
WARNING!
Use of controls or adjustments or performance of procedures other than those
specified
herein
or in the laser product’s installation guide may result in hazardous radiation exposure. To reduce the risk of
exposure to hazardous radiation:
●
Do not try to open the module enclosure. There are no user-serviceable components inside.
●
Do not operate controls, make adjustments, or perform procedures to the laser device other than those
specified
herein.
●
Allow only HP Authorized Service technicians to repair the unit.
Power supply and power cord set requirements
Power supply class I grounding requirements
For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the
system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide
adequate fault protection. Only use the power cord supplied with this product or an HP Inc. authorized
replacement.
Brazil notice
Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia elétrica que possua
aterramento (três pinos), conforme a norma nbr abnt 5410,visando a segurança dos usuários contra choques
elétricos.
Denmark
Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.
Finland
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan.
Norway
Apparatet må tilkoples jordet stikkontakt.
Sweden
Apparaten skall anslutas till jordat uttag.
Power supply requirements
The power supplies on some products have external power switches. The voltage select switch feature on the
product permits it to operate from any line voltage between 100-127 or 200-240 volts AC. Power supplies on
those products that do not have external power switches are equipped with internal circuits that sense the
incoming voltage and automatically switch to the proper voltage.
WARNING!
To reduce potential safety issues, only the AC adapter provided with the computer, a
replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used
with the computer.
Power supply and power cord set requirements
17