HP Designjet L26500 HP Designjet L26500 Printer series - User's Guide - Page 42

during

Get HP Designjet L26500 PDF manuals and user guides View all HP Designjet L26500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

9. Press the OK button on the front panel. Advance the substrate using the arrows on the front panel. Make sure that the substrate passes in front of the loading table, as shown. 10. Pull down the center of the substrate's leading edge to straighten the substrate. Do not attempt to pull more substrate out of the printer. NOTE: If you are loading the take-up reel during printing you do not need to pull the substrate taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the printer after printing begins. 11. Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate. 12. Tape the leading edge of the substrate to the core in the center, then at each side. Make sure that the substrate is straight. 13. Press the OK button on the front panel. The printer advances the substrate. Handle the substrate 38 Chapter 4 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
9.
Press the OK button on the front panel.
Advance the substrate using the arrows on the front panel. Make sure that the substrate passes in
front of the loading table, as shown.
10.
Pull down the center of the substrate's leading edge to straighten the substrate. Do
not
attempt to
pull more substrate out of the printer.
NOTE:
If you are loading the take-up reel
during
printing you do not need to pull the substrate
taut. Tape the substrate to the spindle core when an adequate length of substrate has fed from the
printer after printing begins.
11.
Adjust the position of the core on the take-up reel spindle so that it is aligned with the substrate.
12.
Tape the leading edge of the substrate to the core in the center, then at each side. Make sure that
the substrate is straight.
13.
Press the
OK
button on the front panel. The printer advances the substrate.
38
Chapter 4
Handle the substrate
ENWW
Handle the substrate