HP GbE2c HP BladeSystem c7000 Enclosure Maintenance and Service Guide - Page 49

Insight Display front-to-rear interconnect board

Get HP GbE2c - Blc Layer 2/3 Fiber SFP Option PDF manuals and user guides
UPC - 808736802215
View all HP GbE2c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

e. Use the handholds to extend and remove the rear cage from the enclosure. To replace the component, reverse the removal procedure. Insight Display front-to-rear interconnect board WARNING: To reduce the risk of damage to the midplane and component connectors, always remove or disengage and extend all blades and power supplies approximately 8 cm (3 in) before removing or installing the rear cage. To remove the component: 1. Power down the server blades ("Power down the server blades or workstation blades" on page 30). 2. Power down the enclosure (on page 31). 3. Disconnect all cables. 4. Remove the half-height and full-height blades ("Half-height or full-height blade" on page 36). 5. Remove the device bay blanks ("Device bay blank" on page 33). 6. Remove the power supplies ("HP BladeSystem c7000 power supply or power supply blank" on page 32). 7. Remove the fans ("Active Cool 200 fan" on page 41). 8. Remove the interconnect switches and Pass-Thru modules ("Interconnect switch or Pass-Thru module" on page 42). 9. Remove the Onboard Administrator modules ("Onboard Administrator" on page 44). 10. Remove the Onboard Administrator tray ("Onboard Administrator tray" on page 45). 11. Remove the rear cage ("Rear cage" on page 47). WARNING: To reduce the risk of personal injury or equipment damage, at least two people are needed to safely move the rear cage. Removal and replacement procedures 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Removal and replacement procedures
49
e.
Use the handholds to extend and remove the rear cage from the enclosure.
To replace the component, reverse the removal procedure.
Insight Display front-to-rear interconnect board
WARNING:
To reduce the risk of damage to the midplane and component connectors,
always remove or disengage and extend all blades and power supplies approximately 8 cm
(3 in) before removing or installing the rear cage.
To remove the component:
1.
Power down the server blades ("Power down the server blades or workstation blades" on page 30).
2.
Power down the enclosure (on page 31).
3.
Disconnect all cables.
4.
Remove the half-height and full-height blades ("Half-height or full-height blade" on page 36).
5.
Remove the device bay blanks ("Device bay blank" on page 33).
6.
Remove the power supplies ("HP BladeSystem c7000 power supply or power supply blank" on page
32).
7.
Remove the fans ("Active Cool 200 fan" on page 41).
8.
Remove the interconnect switches and Pass-Thru modules ("Interconnect switch or Pass-Thru module"
on page 42).
9.
Remove the Onboard Administrator modules ("Onboard Administrator" on page 44).
10.
Remove the Onboard Administrator tray ("Onboard Administrator tray" on page 45).
11.
Remove the rear cage ("Rear cage" on page 47).
WARNING:
To reduce the risk of personal injury or equipment damage, at least two people
are needed to safely move the rear cage.