HP Jetdirect 640n HP Jetdirect 640n and 695n Print Server - Setup Guide - Page 35

Link Speed, 10T Half, 10T Full, Print Protocols, Novell NetWare, AppleTalk, DLC/LLC.

Get HP Jetdirect 640n PDF manuals and user guides View all HP Jetdirect 640n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Table A-1 HP Jetdirect EIO Menu on Graphical Control Panel (continued) Menu item Sub-menu item Sub-menu item Values and Description Link Speed The link speed and communication mode of the print server must match the network. The available settings depend on the device and installed print server. Select one of the following link configuration settings: CAUTION: If you change the link setting, network communications with the print server and network device might be lost. Auto (default): The print server uses auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/ switch port. (A 1000T half-duplex selection is not supported.) 10T Half: 10 Mbps, half-duplex operation. 10T Full: 10 Mbps, Full-duplex operation. 100TX Half: 100 Mbps, half-duplex operation. 100TX Full: 100 Mbps, full-duplex operation. 100TX Auto: Limits auto-negotiation to a maximum link speed of 100 Mbps. 1000TX Full: 1000 Mbps, full-duplex operation. Print Protocols Use this item to print a page that lists the configuration of the following protocols: IPX/SPX, Novell NetWare, AppleTalk, DLC/LLC. ENWW HP Jetdirect Menus for Graphical Control Panels 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Table A-1
HP Jetdirect EIO Menu on Graphical Control Panel (continued)
Menu item
Sub-menu item
Sub-menu item
Values and Description
Link Speed
The link speed and communication mode of the print
server must match the network. The available
settings depend on the device and installed print
server. Select one of the following link configuration
settings:
CAUTION:
If you change the link setting, network
communications with the print server and network
device might be lost.
Auto
(default): The print server uses auto-negotiation
to configure itself with the highest link speed and
communication mode allowed. If auto-negotiation
fails, either 100TX HALF or 10TX HALF is set
depending on the detected link speed of the hub/
switch port. (A 1000T half-duplex selection is not
supported.)
10T Half
: 10 Mbps, half-duplex operation.
10T Full
: 10 Mbps, Full-duplex operation.
100TX Half
: 100 Mbps, half-duplex operation.
100TX Full
: 100 Mbps, full-duplex operation.
100TX Auto
: Limits auto-negotiation to a maximum
link speed of 100 Mbps.
1000TX Full
: 1000 Mbps, full-duplex operation.
Print Protocols
Use this item to print a page that lists the
configuration of the following protocols: IPX/SPX,
Novell NetWare, AppleTalk, DLC/LLC.
ENWW
HP Jetdirect Menus for Graphical Control Panels
27