HP L6017tm Installation Instructions - Page 1
HP L6017tm Manual
View all HP L6017tm manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
HP Retail RP7 VFD Customer Display Installation Instructions Installing the VFD 1. Slide down the two levers on the upper corners of the rear I/O panel 1 and rotate the cover off 2. 4. If you are installing the VFD with no poles attached, assemble the VFD display by inserting the VFD cable through the center of the mounting bracket 1 and slide the VFD onto the mounting bracket 2. 7. Wrap the excess extension cable around the hooks on the rear of the base. 10. Replace the power supply cover by lowering it down over the neck of the base then sliding it back until it snaps in place. © Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Printed in Second Edition: October 2012 691056-002 2. Pull the power supply cover back then lift it up and off the unit. 5. If you are installing the VFD with poles attached, slide either one or two poles onto the mounting bracket, depending on the desired height of the VFD. Thread the VFD cable through the top of the pole assembly and out the bottom of the mounting bracket 1, then slide the VFD onto the pole assembly 2. 8. Position the decorative plate onto the rear of the base and press down to snap it in place. 11. Replace the rear I/O cover by placing the hooks on the bottom of the cover into the slots on the bottom of the chassis 1. Then rotate the top of the I/O cover up so that it snaps securely onto the chassis 2. Before Your Begin Before installing the vacuum fluorescent display (VFD), be sure to power off the system and disconnect the power cord from the power outlet. WARNING! To avoid the risk of serious injury, ensure that the power cord is unplugged from the electrical outlet at the wall before installing the VFD. Failure to do so may expose you to the risk of electric shock. CAUTION: To avoid the risk of damage to the system, ensure that the power cord is unplugged from the electrical outlet at the wall before installing the VFD. Online Technical Support For the online access to technical support information, self-solve tools, online assistance, community forums or IT experts, broad multivendor knowledge base, monitoring and diagnostic tools, go to www.hp.com/support. Localized Versions of this Document Localized versions of this document are available at www.hp.com for the following languages: • Simplified Chinese • Traditional Chinese • Bahasa Indonesian • Brazilian Portuguese • Spanish • Japanese • Korean • Thai • German • Italian • Dutch • English • French 3. Remove the decorative panel from the rear of the unit by gently prying the panel away from the base at the tab locations on the top and sides of the panel as indicated below 1. Then pull the top of the panel away from the base 2 and push straight down on the panel to release the bottom tabs 3. 6. From the assembled pole, route the VFD cable through the hole in the new decorative panel 1 that was included with the VFD, then through the rear of the base 2 and out the front of the base. Continue to route the extension cable up through the cable retainer 3 and connect the VFD cable to the 12V USB port on the RP7 4. 9. Slide the VFD mounting bracket into the mounting hole on the rear of the RP7 base 1, and install the two screws included with the VFD into the screw holes on top of the mounting bracket 2. To configure the VFD, refer to the HP Point of Sale Configuration Guide (available in English only). The guide is available on the HP factory image of the RP7 system's hard drive and at www.hp.com. To access the guide on the factory image: • In Windows XP or Windows Embedded POSReady 2009, select Start > All Programs > HP Point of Sale Information. • In Windows 7 or Windows Embedded POSReady 7, select Start > HP Point of Sale Information. Check www.hp.com for updated software or documentation that became available between the time your product was manufactured and delivered to you.