HP MSA 2040 HP MSA 2040 Drive Module Replacement Instructions (732221-001, Jun
HP MSA 2040 Manual
 |
View all HP MSA 2040 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP MSA 2040 manual content summary:
- HP MSA 2040 | HP MSA 2040 Drive Module Replacement Instructions (732221-001, Jun - Page 1
configuration. For additional information on replacing drives, go to the following HP websites: ◦ MSA 2040 Guided Troubleshooting: http://www.hp.com/support/msa2040/ Troubleshooting ◦ HP MSA 2040 User Manual: http://www.hp.com/support/msa2040/ manuals • Leave failed modules in the enclosure until - HP MSA 2040 | HP MSA 2040 Drive Module Replacement Instructions (732221-001, Jun - Page 2
, product-specific logs, and management utilities for drive health and location information. • Check enclosure status LEDs. • Check drive LEDs, as described in the following image and table. Removing the failed drive CAUTION: When replacing multiple drives, remove only one drive at a time from the - HP MSA 2040 | HP MSA 2040 Drive Module Replacement Instructions (732221-001, Jun - Page 3
://www.hp.com/support/msa2040/ manuals. • MSA 2040 Guided Troubleshooting • HP MSA 2040 User Manual • HP MSA 2040 SMU Reference Guide • HP MSA 2040 CLI Reference Guide Verifying proper operation Confirm that the drive is operating normally. See "Verifying drive status" (page 2). Updating firmware - HP MSA 2040 | HP MSA 2040 Drive Module Replacement Instructions (732221-001, Jun - Page 4
http://www.hp.com/go/storage MSA 2040 Manuals page: http://www.hp.com/ support/msa2040/Manuals MSA 2040 product page: http://www.hp.com/ support/msa2040 HP MSA Guided Toubleshooting: nl http://www.hp.com/support/msa2040/ Troubleshooting Warranty statement Warranties for HP products and services are
-
1 -
2 -
3 -
4
 |
 |
HP MSA 2040
nl
Drive Module
nl
Replacement Instructions
Abstract
This document details procedures for replacing failed drive
modules in an HP MSA 2040 controller and drive
enclosures. Read this entire document before replacing a
drive. Incorrectly removing an operational, failing, or failed
drive from an enclosure might cause data loss.
© Copyright 2013 Hewlett-Packard Development Company, L.P.
*732221-001*
HP Part Number: 732221-001
Published: June 2013
Edition: 1
Before you begin
•
Before proceeding, check the following:
Confirm that the drive is a member of a
fault-tolerant configuration that permits
◦
removing one or more drives without risking
data loss.
◦
If multiple drives have failed and need
replacing, determine how many drives can be
replaced at the same time. The number of
drives that can fail and be replaced without
data loss is determined by the fault-tolerance
level of the configuration.
For additional information on replacing drives,
go to the following HP websites:
◦
MSA 2040 Guided Troubleshooting:
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/ms
a20
4
0/
T
r
o
u
ble
sh
oo
ting
◦
HP MSA 2040 User Manual:
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/ms
a20
4
0/
man
uals
•
Leave failed modules in the enclosure until you
are ready to install the replacement module.
Removing a module from an operational enclosure
significantly changes air flow within the enclosure.
Openings must be populated for the enclosure to
cool properly.
•
Parts can be damaged by electrostatic discharge.
Keep parts in electrostatic containers until needed
and ensure you are properly grounded when
touching static-sensitive components.
•
Use care when handling drives. Drives are
sensitive electromechanical devices that can be
permanently damaged through improper
handling. Keep drives in their original, protective
packaging until installation.
•
The replacement drive module must be of the
same type, and possess capacity equal to or
greater than the one being replaced.
Page 1