HP Model 712/100 hp DDS-3 tape drive user's guide (a1658-90702) - Page 44

Removing and Replacing the DDS-3 Drive, Adding or Removing the DDS-3 Drive Bezels and Expansion

Get HP Model 712/100 - Workstation PDF manuals and user guides View all HP Model 712/100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Troubleshooting and Removal/Replacement Procedures Removing and Replacing the DDS-3 Drive To open your system and to remove and reinstall the DDS-3 drive, refer to the owner's guide that came with your system. Read "Preparing to Install the DDS-3 Drive" in Chapter 1 of this guide before beginning an installation. Adding or Removing the DDS-3 Drive Bezels and Expansion Brackets Depending on the size of the drive opening in your system, you may need to add or remove a bezel or expansion brackets to ensure that your DDS-3 drive fits in your system. NOTICE: Before performing any of these changes, make sure there is not a cassette in the drive. • To add a bezel (it can be a 3.5-inch bezel, or a 5.25-inch bezel) to your drive, push onto the drive, making sure the tabs click into place. Refer to Figure 3-1. • To remove a bezel from a drive, use a straight blade screwdriver to lift the bezel tabs from the top of the drive, and push in the tabs on the sides of the drive. Refer to Figure 3-2. • To add or remove expansion brackets to the drive, use a T10 torx wrench to ei- ther tighten or remove the four torx screws that hold each expansion bracket to the drive. Refer to Figure 3-3. 3-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
Troubleshooting and Removal/Replacement Procedures
3–9
Removing and Replacing the DDS-3 Drive
To open your system and to remove and reinstall the DDS-3 drive, refer to the owner’s
guide that came with your system. Read “Preparing to Install the DDS-3 Drive” in
Chapter 1 of this guide before beginning an installation.
Adding or Removing the DDS-3 Drive Bezels and Expansion Brackets
Depending on the size of the drive opening in your system, you may need to add or
remove a bezel or expansion brackets to ensure that your DDS-3 drive fits in your
system.
NOTICE:
Before performing any of these changes, make sure there is not a
cassette in the drive.
•
To add a bezel (it can be a 3.5-inch bezel, or a 5.25-inch bezel) to your drive,
push onto the drive, making sure the tabs click into place. Refer to Figure 3–1.
•
To remove a bezel from a drive, use a straight blade screwdriver to lift the bezel
tabs from the top of the drive, and push in the tabs on the sides of the drive.
Refer to Figure 3–2.
•
To add or remove expansion brackets to the drive, use a T10 torx wrench to ei-
ther tighten or remove the four torx screws that hold each expansion bracket to
the drive. Refer to Figure 3–3.