Home » HP Manuals » Desktops » HP PL Class450/500/550/600/650/700/750 » Manual Viewer

HP PL Class450/500/550/600/650/700/750 HP Visualize PL500, PL600, PL650, and P - Page 105

Internal Audio Connectors

Get HP PL Class450/500/550/600/650/700/750 PDF manuals and user guides

View all HP PL Class450/500/550/600/650/700/750 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Technical Information System Connectors and Switches CD Audio Connector Auxiliary (AUX) Connector Internal Audio Connectors The Workstation's system board has several connectors that allow you to internally connect to other devices. This includes: • A CD audio connector • An auxiliary (AUX) connector • An Audio Front Panel connector • A Front Panel Microphone connector The CD Audio Connector labeled "CD IN," is a 4-pin connector that is connected to the internal CD drive. This connector allows you to listen to audio from the CD-ROM drive. The CD Audio Connector has the following pin assignments: Pin Signal I/O 1 Analog Ground 2 CD right IN channel 3 Analog Ground 4 CD left channel IN The AUX Connector labeled "AUX IN," is a 4-pin connector that is connected to the internal AUX. This connector allows you to listen to audio from an auxiliary source. The AUX Connector has the following pin assignments: Pin Signal I/O 1 Analog Ground 2 AUX right IN channel 3 Analog Ground 4 AUX left IN channel Chapter 4 89

Section	Page
HP VISUALIZE Linux Workstation Owner’s Guide	1
HP VISUALIZE Linux Workstation Owner’s Guide	1
HP VISUALIZE Linux Workstation Owner’s Guide	1
PL-Class Workstations	1
Printed in USA	1
Manufacturing Part Number: A1296-90001	1
Edition E1299	1
© Copyright 1999	1
© Copyright 1999	1
Hewlett-Packard Company	1
Legal Notices	2
Legal Notices	2
The information contained in this document is subject to change without notice. Hewlett-Packard m...	2
Trademark Acknowledgments	2
Adobe® Reader © 1987-1999 Adobe Systems Incorporated. All rights reserved. Adobe and Acrobat are ...	2
Red Hat®, the Red Hat “Shadow Man” logo, RPM, Maximum RPM, the RPM logo, Linux Library, PowerTool...	2
HP Printing Division:	2
Hewlett-Packard Company 3404 E. Harmony Road Fort Collins, CO 80528-9599 USA	2
IMPORTANT HP Linux/Year 20000 Warranty Information	3
IMPORTANT HP Linux/Year 20000 Warranty Information	3
IMPORTANT HP Linux/Year 20000 Warranty Information	3
HP has made every effort to ensure the accuracy of our product testing. However, because each cus...	3
http://www.redhat.com	3
Contents	5
Chapter 1 Setting Up and Using Your HP Visualize LinuxWorkstation 1	6
Chapter 2 How to Install Accessories In Your HP Visualize Linux Workstation 19	6
Chapter 3 Troubleshooting Your HP Visualize Linux Workstation 55	7
Chapter 4 Technical Information 77	7
Chapter 5 Hewlett Packard Support and Information Services 109	8
Appendix A Regulatory Information and Warranty 121	9
Appendix B Physical Characteristics 135	9
Preface	11
Preface	11
This owner’s guide describes how to use your HP Visualize Linux PL-Class Workstation. This Workst...	11
The PL-Class Workstation is designed to perform such tasks as locally executed IC design. It prov...	11
Red Hat Linux is a popular open source operating system that gives you the ability to develop cus...	12
Special Notice for Users	13
Special Notice for Users	13
The HP Visualize Linux Workstation is made from a combination of high performance Industry Standa...	13
Audience	13
Audience	13
This guide is intended for HP Visualize Linux Workstation users who want to:	13
• Set up the HP Visualize Linux Workstation for the first time.	13
• Set up the HP Visualize Linux Workstation for the first time.	13
• Configure the HP Visualize Linux Workstation.	13
• Troubleshoot problems on the HP Visualize Linux Workstation.	13
• Add accessories to the HP Visualize Linux Workstation.	13
• Find out where to get more information and support.	13
Important Safety Information	14
Important Safety Information	14
WARNING If you have any doubt that you can lift the HP Visualize Linux Workstation or display saf...	14
WARNING If you have any doubt that you can lift the HP Visualize Linux Workstation or display saf...	14
Important Ergonomic Information	14
Important Ergonomic Information	14
It is strongly recommended that you read the ergonomic information before using you HP Visualize ...	14
Installation Notice	15
Installation Notice	15
Products designated in the applicable Hewlett-Packard price list as customer-installable can be i...	15
Revision History	15
Revision History	15
The revision history for each edition of the manual is listed below:	15
Edition	15
Edition	15
Edition	15
Revision History	15
Revision History	15
E1299	15
E1299	15
Second Printing	15
Second Printing	15
Problems, Questions, and Suggestions	15
Problems, Questions, and Suggestions	15
If you have any problems or questions with our hardware or documentation, please contact either y...	15
For further information about HP Linux program:	15
http://www.hp.com/visualize/products/linux	15
For more information about the Red Hat Operating System, see:	15
http://www.redhat.com	15
Documentation Conventions	16
Documentation Conventions	16
Unless otherwise noted in the text, this guide uses the following symbolic conventions.	16
<TABLE>	16
<TABLE BODY>	16
<TABLE ROW>	16
user-supplied values	16
Italic words or characters in syntax and command descriptions represent values that you must supp...	16
<TABLE ROW>	16
screen display	16
Information that the system displays, commands that you must use literally, and path names appear...	16
<TABLE ROW>	16
Enter	16
Enter	16
Keycaps are presented with a special keycap font as shown in the left column. (In this document, ...	16
Electrostatic Discharge (ESD) Precautions	16
Electrostatic Discharge (ESD) Precautions	16
ESD (electrostatic discharge)	16
ESD (electrostatic discharge)	16
Electrostatic discharge (ESD)	16
• Stand on a static-free mat.	16
• Stand on a static-free mat.	16
• Stand on a static-free mat.	16
• Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your...	16
• Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your...	16
• Create a common ground for the equipment you are working on by connecting the static-free mat, ...	16
• Create a common ground for the equipment you are working on by connecting the static-free mat, ...	16
• Keep uninstalled printed circuit boards in their protective antistatic bags.	16
• Keep uninstalled printed circuit boards in their protective antistatic bags.	16
• Handle printed circuit boards by their edges, once you have removed them from their protective ...	16
• Handle printed circuit boards by their edges, once you have removed them from their protective ...	16
1 Setting Up and Using Your HP Visualize LinuxWorkstation	17
1 Setting Up and Using Your HP Visualize LinuxWorkstation	17
unpacking the Personal Workstation	18
unpacking the Personal Workstation	18
unpacking the Personal Workstation	18
Personal Workstation:unpacking	18
WARNING If you are in any doubt that you can lift the Workstation and the display safely, do not ...	18
WARNING If you are in any doubt that you can lift the Workstation and the display safely, do not ...	18
1. When you receive your Workstation, unpack all of the components:	18
1. When you receive your Workstation, unpack all of the components:	18
1. When you receive your Workstation, unpack all of the components:	18
Computer and power cords	18
Computer and power cords	18
Display and its video cable	18
HP keyboard, mouse and headphones	18
Manuals and CD-ROMs.	18
2. Place the Workstation on (or under) a sturdy desk with easily accessible power outlets and eno...	18
2. Place the Workstation on (or under) a sturdy desk with easily accessible power outlets and eno...	18
<GRAPHIC>	18
4. Place the display next to the computer.	18
Installation Tools	18
No tools are required to install your Workstation. However, if you plan to install a disk drive o...	18
Connecting the Mouse,	19
Connecting the Mouse,	19
Connect the mouse, keyboard, and display to the back of the Workstation.	19
<GRAPHIC>	19
Connect the printer cable to the back of the computer and tighten the attachment screws. Use the ...	19
• Parallel (25-pin parallel connector) for a parallel device.	19
• Parallel (25-pin parallel connector) for a parallel device.	19
• Serial A (9-pin serial connector) for a serial device.	19
• Serial B (9-pin serial connector) for a second serial device.	19
connector:printer;printer:connector	20
Connecting to a Network	20
Your HP Visualize Linux Workstation has a 10BT/100TX LAN interface adapter.	20
The LAN adapter supports both 10 Mbit/s and 100 Mbit/s operations and automatically detects which...	20
1. Connect the RJ-45 plug on your network cable to the LAN connector on the LAN Adapter. Push the...	20
1. Connect the RJ-45 plug on your network cable to the LAN connector on the LAN Adapter. Push the...	20
1. Connect the RJ-45 plug on your network cable to the LAN connector on the LAN Adapter. Push the...	20
<GRAPHIC>	20
For further instructions on configuring your network connection, refer to the section “Configurin...	20
Let your Network Administrator know that you are connecting yourWorkstation to the network.	20
Connecting Audio Accessories	21
Connecting Audio Accessories	21
Your HP Visualize Linux Workstation has a Headphone Out jack and a Microphone In jack on the Audi...	21
<GRAPHIC>	22
WARNING To avoid discomfort from unexpected noise, always turn down the volume before connecting ...	22
WARNING To avoid discomfort from unexpected noise, always turn down the volume before connecting ...	22
Connecting an External SCSI Accessory	23
Connecting an External SCSI Accessory	23
SCSI:Ultra wide 16-bit;SCSI:Ultra narrow 8-bit	23
Your HP Visualize Linux Workstation is equipped with an UltraWide 16-bit SCSI connector for exter...	23
When an external SCSI device is connected, the UltraWide 16-bit SCSI controller automatically swi...	23
An external SCSI device is connected as follows:	23
1. You should assign an unused SCSI address to the accessory. SCSI addresses range from 0 to 15 f...	23
1. You should assign an unused SCSI address to the accessory. SCSI addresses range from 0 to 15 f...	23
1. You should assign an unused SCSI address to the accessory. SCSI addresses range from 0 to 15 f...	23
Refer to the manual provided with the SCSI accessory for instructions on selecting a SCSI address.	23
NOTE You don’t need to set a SCSI address for Plug and Play SCSI devices (SCSI devices which supp...	23
NOTE You don’t need to set a SCSI address for Plug and Play SCSI devices (SCSI devices which supp...	23
2. Make sure the SCSI accessory is terminated correctly—either internally or by a terminating res...	23
3. Connect the SCSI accessory to your Workstation’s external 16-bit SCSI connector with a shielde...	24
4. Refer to the manual provided with the SCSI accessory to learn how to install any software that...	24
NOTE The total length of the external SCSI cables should not exceed 3 meters (approximately 10 fe...	24
NOTE The total length of the external SCSI cables should not exceed 3 meters (approximately 10 fe...	24
See the section “Installing Mass Storage Devices” in the chapter “How to Install Accessories Insi...	24
Connecting the Power Cords	25
Connecting the Power Cords	25
1. Remove any warning labels that may be covering the computer’s power connector on the rear of t...	25
1. Remove any warning labels that may be covering the computer’s power connector on the rear of t...	25
2. Connect the power cords to the display and the computer. (The connectors are shaped to go in o...	25
3. Connect the display’s power cord and the computer’s power cord to grounded outlets.	25
WARNING For your safety, always connect the equipment to a grounded wall outlet. Always use a pow...	25
WARNING For your safety, always connect the equipment to a grounded wall outlet. Always use a pow...	25
Your HP Visualize Linux Workstation’s Hardware Control Panel	26
Your HP Visualize Linux Workstation’s Hardware Control Panel	26
control panel	26
The hardware control panel is located on the front of your Workstation.	26
<GRAPHIC>	26
HP MaxLife and its Liquid Crystal Display (LCD)	26
HP MaxLife and its LCD helps you diagnose problems with your Workstation and provides system info...	26
Network Activity Light	26
network:activity light;activity light:network	26
This light glows/flickers when your Workstation is accessing the network.	26
Hard Disk Activity Light	26
hard disk:activity light;activity light:hard disk	26
This light glows/flickers when your hard disk drive is being accessed.	26
starting:and stopping Personal Workstation	27
starting:and stopping Personal Workstation	27
starting:and stopping Personal Workstation	27
Personal Workstation:starting and stopping	27
Starting Your Workstation for the First Time	27
Starting Your Workstation for the First Time	27
Your HP Visualize Linux Workstation has preinstalled Red Hat Linux and HP software. It is initial...	27
Initializing Your Software	27
Initializing Your Software	27
NOTE Do NOT switch OFF the Workstation while the software is being initialized—this could cause u...	27
NOTE Do NOT switch OFF the Workstation while the software is being initialized—this could cause u...	27
software:initializing	28
software:initializing	28
initializing:software	28
1. Turn on the display first, and then the HP Visualize Linux Workstation.	28
1. Turn on the display first, and then the HP Visualize Linux Workstation.	28
1. Turn on the display first, and then the HP Visualize Linux Workstation.	28
When the Workstation is switched on, the Workstation performs a Power-On-Self-Test (POST).	28
If an error is detected during the Power-On-Self-Test, the Workstation will automatically display...	28
The HP Linux Setup Tool will then run. It allows you to enter information. For example:	28
• The Boot Protocol, networking parameters, current date and time, root password, etc.	28
• The Boot Protocol, networking parameters, current date and time, root password, etc.	28
2. While the Setup Tool is running, you can complete the Warranty Registration card that came wit...	28
3. When you are finished entering information into the Setup Tool, click OK and the Workstation ...	28
Creating Rescue Disk Set	28
Creating Rescue Disk Set	28
It is very important that you create a rescue disk set for your preloaded software and operating ...	28
Starting Your HP Visualize Linux Workstation	29
Starting Your HP Visualize Linux Workstation	29
1. Before you start your Workstation, first switch on the display.	29
1. Before you start your Workstation, first switch on the display.	29
2. Start your Workstation by pressing the power button on the front panel.	29
2. Start your Workstation by pressing the power button on the front panel.	29
When you switch on the computer, it carries out the Power-On-Self-Test (POST). If you wish to vie...	29
If you have set a password in the Workstation’s	29
stopping:Personal Workstation	29
stopping:Personal Workstation	29
stopping:Personal Workstation	29
Personal Workstation:stopping	29
To stop the Workstation, make sure that you have exited all programs and the operating system by ...	29
shutdown -h now	29
and then press the power button on the control panel. If you stop the workstation without followi...	29
Additional Information and Help	30
Additional Information and Help	30
<GRAPHIC>	30
After completing the Setup Tool and rebooting, your Workstation will launch a special “Getting St...	30
Setting BIOS Passwords	31
Setting BIOS Passwords	31
You can set two passwords, the Administrator (or Supervisor) password and the User password, to p...	31
Setting an Administrator Password	31
Setting an Administrator Password	31
Set the Administrator password to protect the HP Visualize Linux Workstation’s configuration in t...	31
If you have set both an Administrator password and a User password, and you enter theBIOS Setup p...	31
To set an Administrator password:	31
1. Start the BIOS	31
1. Start the BIOS	31
2. Select the Security menu.	31
3. Select the Administrator password submenu.	31
4. Choose the Set Administrator password setup item. You will be asked to enter your password twi...	31
To remove the password, follow the same procedure as to set a password. You will be asked to ente...	31
NOTE If you forget your password, refer to the section “If You Have Forgotten Your Password” in t...	32
NOTE If you forget your password, refer to the section “If You Have Forgotten Your Password” in t...	32
Setting a User Password	32
Setting a User Password	32
A User password can only be set if an Administrator password has already been set.	32
Set a User password to:	32
• Provide a power-on password prompt to prevent your Workstation being started or used in your a...	32
• Provide a power-on password prompt to prevent your Workstation being started or used in your a...	32
• Start the Workstation when the keyboard and mouse are locked—you must type the password and press	32
If you have set both an Administrator password and a User password, and you enter the Setup progr...	32
To set a User password:	32
1. Start the BIOS	32
1. Start the BIOS	32
2. Select the Security menu.	32
3. Select the User Password submenu.	32
4. Choose the Set User Password setup item. You will be asked to enter your password twice. Save ...	32
To remove the password, follow the same procedure as to set a password. You will be asked to ente...	33
NOTE If you forget your password, refer to the section “If You Have Forgotten Your Password” in t...	33
NOTE If you forget your password, refer to the section “If You Have Forgotten Your Password” in t...	33
Recycling an Old HP Workstation	34
Recycling an Old HP Workstation	34
HP has a strong commitment towards the environment. This HP Workstation has been designed to res...	34
HP can take an old computer back for recycling when it reaches the end of its useful life.	34
In several countries, HP has a product take-back program. Collected equipment is sent to one of H...	34
If you require more details about HP’s product take-back program, contact your dealer or your nea...	34
2 How to Install Accessories In Your HP Visualize Linux Workstation	35
2 How to Install Accessories In Your HP Visualize Linux Workstation	35
This chapter explains how to install accessories, such as extra memory, accessory boards, and add...	36
accessories:supported	37
accessories:supported	37
accessories:supported	37
supported HP accessories	37
This chapter describes how to install memory, mass storage devices, and accessory boards in your ...	37
<GRAPHIC>	37
<GRAPHIC>	37
IMPORTANT Some of the accessories mentioned in this section reflect components that were not full...	37
IMPORTANT Some of the accessories mentioned in this section reflect components that were not full...	37
Contact HP or your dealer for an up-to-date list of supported devices.	37
Removing and Replacing the Cover	38
Removing and Replacing the Cover	38
WARNING For your safety, never remove the Workstation’s cover without first removing the power co...	38
WARNING For your safety, never remove the Workstation’s cover without first removing the power co...	38
Removing the Cover	38
Removing the Cover	38
cover:removing	38
1. Switch off the display and computer.	38
1. Switch off the display and computer.	38
2. Disconnect all power cables and any telecommunications cables.	38
2. Disconnect all power cables and any telecommunications cables.	38
<GRAPHIC>	38
<GRAPHIC>	39
<GRAPHIC>	39
5. Grasp the cover on the sides at the back of the computer and slide it forwards and off the com...	39
Replacing the Cover	40
Replacing the Cover	40
1. Ensure that you have installed all your accessories and that all internal cables are properly ...	40
1. Ensure that you have installed all your accessories and that all internal cables are properly ...	40
2. Ensure that the two latches on the front sides of the cover are lifted up, and that the lock i...	40
3. Slide the cover onto the computer, making sure that the two guides at the bottom of the case s...	40
3. Slide the cover onto the computer, making sure that the two guides at the bottom of the case s...	40
<GRAPHIC>	41
4. Lower the latches on the front sides of the cover.	41
<GRAPHIC>	41
6. Reconnect all the power cables.	41
Intrusion Monitor	41
intrusion monitor	41
Your HP Visualize Linux Workstation is equipped with an intrusion monitor, which is located on th...	41
• If your Workstation has been opened, it is assumed that the system configuration has changed an...	41
• If your Workstation has been opened, it is assumed that the system configuration has changed an...	41
• If your Workstation has not been opened, it is assumed that the system configuration has not ch...	41
power supply:removing	42
power supply:removing	42
power supply:removing	42
removing:power supply	42
You can slide the power supply unit out of the computer to improve access to the system board and...	42
1. Disconnect the computer’s power cord and any telecommunications cable.	42
1. Disconnect the computer’s power cord and any telecommunications cable.	42
2. Remove the computer’s cover (see the section “Removing and Replacing the Cover”).	42
3. Remove the fan connection to the system board.	42
4. Press the retaining buttons on each side of the HP UltraFlow airflow guide and lift it out of ...	42
5. Unscrew the four self-retaining screws at the back of the power supply.	43
5. Unscrew the four self-retaining screws at the back of the power supply.	43
<GRAPHIC>	43
WARNING To avoid electrical shock, do not open the power supply.	43
WARNING To avoid electrical shock, do not open the power supply.	43
6. Slide the power supply out of the computer until it stops—the power supply unit remains connec...	43
6. Slide the power supply out of the computer until it stops—the power supply unit remains connec...	43
<GRAPHIC>	44
replacing:power supply	44
power supply:replacing	44
1. Check that all internal cables are safely routed.	44
1. Check that all internal cables are safely routed.	44
2. Slide the power supply back into the computer.	44
3. Tighten the four self-retaining screws.	44
4. Replace the HP UltraFlow airflow guide.	44
5. Reconnect the fan to the system board.	44
Installing Memory	45
Installing Memory	45
Main Memory Modules	45
Main Memory Modules	45
If you need more main memory to run your application software, you can install up to 768 MB of me...	45
Main memory upgrades are available in single 128 MB and 256 MB ECC SDRAM memory modules. You shou...	45
CAUTION Static electricity can damage electronic components. Turn off all equipment. Do not let y...	45
CAUTION Static electricity can damage electronic components. Turn off all equipment. Do not let y...	45
To install a main memory module:	45
To install a main memory module:	45
1. Disconnect the computer’s power cord and any LAN or telecommunications cable	45
1. Disconnect the computer’s power cord and any LAN or telecommunications cable	45
2. Remove the computer’s cover (see the section “Removing and Replacing the Cover”).	45
3. Remove the fan connection to the system board.	45
4. Press the retaining buttons on each side of the HP UltraFlow airflow guide and lift it out of ...	46
5. Remove the transparent airflow guide covering the processor sockets (if needed).	46
6. Remove the floppy disk drive data cable from the system board.	46
7. The location of the memory module slots is shown here.	46
8. Slide the memory module into the slot at 90 to the system board (with the cutouts furthest aw...	46
9. Firmly press the memory module completely into the connector until the retaining clips click i...	47
10. Repeat this procedure for each additional memory module you want to install.	47
11. Install any other accessories if necessary, then replace all units and reconnect all cables a...	47
12. Check the HP Summary Screen to verify the new configuration (refer to the section “The HP Sum...	47
Installing Mass Storage Devices	48
Installing Mass Storage Devices	48
If you need extra mass storage space for your application software, you can install additional ma...	48
The computer has two internal shelves (for hard disk drives) and five front-access drive shelves ...	48
Your computer is supplied with one 3.5-inch flexible disk drive and a CD- ROM drive. If your comp...	48
Connecting Devices	49
Connecting Devices	49
If you add an IDE Zip drive, hard disk drive, CD-ROM drive, CD-RW drive, or tape drive (NOTE: the...	49
<GRAPHIC>	49
Which Data Connectors to Use	49
mass storage devices:connector	49
mass storage devices:connector	49
• A flexible disk drive cable with a single connector. This supports a flexible disk drive (the c...	49
• A flexible disk drive cable with a single connector. This supports a flexible disk drive (the c...	49
• Two Ultra ATA/33 IDE drive connectors that support four fast IDE devices. If you install a CD-R...	49
Which Power Connectors to Use	50
There are two different types of power connectors—these are shown below.	50
Some of the power connectors will already be connected to devices. If you install a device that r...	50
Installing a Hard Disk Drive	50
This Workstation has integrated Dual Ultra ATA-33 IDE controllers and, on selected models, an Ult...	50
• The Dual Ultra ATA-33 IDE controllers, on the PCI bus, support up to four fast (33 MB per secon...	50
• The Dual Ultra ATA-33 IDE controllers, on the PCI bus, support up to four fast (33 MB per secon...	50
• On selected models, the Ultra SCSI 16-bit interface board, installed in a PCI slot, supports up...	50
Before Installing an IDE Hard Disk	50
Refer to the drive’s installation guide to see if you must set jumpers or if there is a special i...	50
Before Installing a SCSI Hard Disk	51
If you are installing an additional SCSI drive, you should assign an unused SCSI address to this ...	51
Plug and Play:SCSI	51
Plug and Play:SCSI	51
Plug and Play:SCSI	51
SCSI:Plug and Play	51
You should assign an unused SCSI address to the second SCSI hard disk drive (for example, SCSI ad...	51
The SCSI address is usually configured with jumpers on the SCSI hard disk drive. Refer to the ins...	51
Some internal SCSI disk drives may have termination resistors that must be removed or disabled be...	51
Installing a Hard Disk Drive in an Internal Shelf	52
Installing a Hard Disk Drive in an Internal Shelf	52
CAUTION The upper internal shelf can house a hard disk drive up to one inch (1”) in height. For a...	52
CAUTION The upper internal shelf can house a hard disk drive up to one inch (1”) in height. For a...	52
1. Disconnect the computer’s power cord and any telecommunications cable.	52
1. Disconnect the computer’s power cord and any telecommunications cable.	52
2. Remove the computer’s cover (see	52
3. Remove the fan connection to the system board (see the illustration on	52
4. Press the retaining buttons on each side of the HP UltraFlow airflow guide and lift it out of ...	52
5. Slide the power supply out to improve access to the internal shelf (see	52
6. Slide the drive into position in the first internal shelf and align the screw holes in the dri...	52
7. Secure the drive with the four self-retaining screws.	53
cables:SCSI	53
cables:SCSI	53
cables:IDE	53
hard disk drive:cables	53
SCSI:cables	53
IDE drive:cables	53
9. Connect the power cable and the data cable to the rear of the drive. (	54
10. Install any other accessories before completing the installation.	54
11. Turn to	54
Installing a Hard Disk Drive in a Front-Access Shelf	54
Installing a Hard Disk Drive in a Front-Access Shelf	54
1. Disconnect the computer’s power cord and any telecommunications cable.	54
1. Disconnect the computer’s power cord and any telecommunications cable.	54
2. Remove the computer’s cover (see	54
3. Remove the fan connection to the system board (see the illustration on	54
4. Press the retaining buttons on each side of the HP UltraFlow airflow guide and lift it out of ...	54
5. Slide out the power supply to provide better access to the disk drive cables (see	54
6. Unscrew and remove an unused drive tray.	55
7. Mount the drive on the tray as shown below.	55
8. Slide the drive tray into the drive shelf and secure it.	56
9.	57
10. Connect the data and power cables to the rear of the device. (	57
11. Slide the power supply back into position, and tighten the four self- retaining screws (see	57
12. Replace the HP UltraFlow airflow guide and reconnect the fan to the system board (see the ill...	58
13. Install any other accessories before replacing the cover and completing the installation.	58
14. Follow the instructions below to complete the installation.	58
hard disk drive:completing installation	58
hard disk drive:completing installation	58
hard disk drive:completing installation	58
When a SCSI Hard Disk Drive Is Installed	58
1. Switch on the computer.	58
1. Switch on the computer.	58
2. To ensure compatibility, use the FDISK utility to delete any partitions on the new hard disk.	58
3. Re-boot the computer.	58
Refer to the operating system documentation for information on formatting a drive.	58
When an IDE Drive Is Installed	58
1. Switch on the computer.	58
1. Switch on the computer.	58
2. To display the device in POST, press	58
3. If an error message appears, follow the instructions provided by the Error Message Utility. Wh...	58
4. Select the Advanced menu, and the IDE Devices submenu. In the Primary Master item, check that ...	58
5. Press	58
Refer to the operating system documentation for information on formatting a drive.	58
NOTE If an IDE drive is removed, switch on the computer. The system BIOS will detect that the dev...	58
NOTE If an IDE drive is removed, switch on the computer. The system BIOS will detect that the dev...	58
Installing a Drive in a Front-Access Shelf	59
Installing a Drive in a Front-Access Shelf	59
These instructions explain how to install a drive (such as a flexible disk drive, a CD-ROM drive,...	59
Before Installing an IDE Device	59
Refer to the drive’s installation guide to see if you must set jumpers or if there is a special i...	59
Before Installing a SCSI Device	59
If you are installing a SCSI device, refer to the section “Before Installing a SCSI Hard Disk” on	59
1. Disconnect the computer’s power cord and any telecommunications cable.	59
1. Disconnect the computer’s power cord and any telecommunications cable.	59
2. Remove the computer’s cover (see	59
3. Slide out the power supply to provide better access to the disk drive cables (see	59
If installing a drive in a 5.25-inch wide shelf, remove the drive tray and put it in a safe place.	60
Slide the drive into the shelf.	60
Secure the drive in position using the screws provided with the drive.	60
cables:SCSI	61
cables:SCSI	61
cables:IDE	61
cables:flexible disk drive	61
flexible disk drive:cables	61
SCSI:cables	61
IDE drive:cables	61
Connect the data and power cables to the rear of the device. (The connectors are shaped to go in ...	61
Slide the power supply back into position, and tighten the four self- retaining screws (see	62
Remove the plastic panel from the cover by pulling the panel from the left and unhinging its righ...	62
Install any other accessories before replacing the cover and completing the installation.	62
CD-ROM:completing installation;floppy disk drive:completing installation;installation:completing, fo	62
CD-ROM:completing installation;floppy disk drive:completing installation;installation:completing, fo	62
CD-ROM:completing installation;floppy disk drive:completing installation;installation:completing, fo	62
When an IDE CD- ROM Drive Is Installed	62
1. Switch on the computer and press	62
1. Switch on the computer and press	62
2. In the	62
3. Press	62
When a Flexible Disk Drive Is Installed	62
1. Switch on the computer and press	62
1. Switch on the computer and press	62