HP Presario V6500 Compaq Presario V6500, V6600, and V6700 Notebook PCs - Maint - Page 80

Remove the Phillips PM2.5×4.0 screw, from the clips built into the base enclosure.

Get HP Presario V6500 - Notebook PC PDF manuals and user guides View all HP Presario V6500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

f. Top cover (see Top cover on page 64) g. Audio board (see Audio board on page 74) h. USB/power connector board (see USB/power connector board on page 70) When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory modules (see Memory module on page 44) ● RTC battery (see RTC battery on page 46) ● WLAN module (see WLAN module on page 47) ● Bluetooth module (see Bluetooth module on page 67) ● ExpressCard assembly (see ExpressCard assembly on page 68) ● Fan/heat sink assembly (see Fan/heat sink assembly on page 75) ● Processor (see Processor on page 78) Remove the system board: 1. Remove the USB/power connector board cable (1) from the clips built into the base enclosure. 2. Remove the Phillips PM2.5×4.0 screw (2) and the Phillips PM2.0×7.0 screw (3) that secure the system board to the base enclosure. 3. Use the optical drive connector (1) to lift the right side of the system board (2) until it rests at an angle. 4. Disconnect the audio board cable (3) from the system board. 72 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
f
.
Top cover (see
Top cover
on page
64
)
g
.
Audio board (see
Audio board
on page
74
)
h
.
USB/power connector board (see
USB/power connector board
on page
70
)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Memory modules (see
Memory module
on page
44
)
●
RTC battery (see
RTC battery
on page
46
)
●
WLAN module (see
WLAN module
on page
47
)
●
Bluetooth module (see
Bluetooth module
on page
67
)
●
ExpressCard assembly (see
ExpressCard assembly
on page
68
)
●
Fan/heat sink assembly (see
Fan/heat sink assembly
on page
75
)
●
Processor (see
Processor
on page
78
)
Remove the system board:
1
.
Remove the USB/power connector board cable
(1)
from the clips built into the base enclosure.
2
.
Remove the Phillips PM2.5×4.0 screw
(2)
and the Phillips PM2.0×7.0 screw
(3)
that secure the
system board to the base enclosure.
3
.
Use the optical drive connector
(1)
to lift the right side of the system board
(2)
until it rests at an
angle.
4
.
Disconnect the audio board cable
(3)
from the system board.
72
Chapter
4
Removal and replacement procedures