HP Scitex LX820 HP Scitex LX850 & LX820 Printer: Installation Guide
HP Scitex LX820 Manual
View all HP Scitex LX820 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Scitex LX820 manual content summary:
- HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 1
Scitex LX850 & LX820 Printers Installation guide - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 2
to change without notice. The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 3
Cautions ...3 Warning labels ...3 Emergency stop buttons ...5 2 Introduction Installation guide overview ...6 Manpower required ...6 Tools required for installation ...6 Inbox content ...7 3 Receive the shipment Unload the crate ...9 Move the printer over ramps ...10 Remove the crate packaging ...10 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 4
...64 Connect the air supply ...64 Configure the RIP ...65 Install the covers ...67 Print the HP test images ...68 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) Appendix B Manually configure the printer's IP address Appendix C Change the Windows Vista language iv ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 5
to minimize the risks to that person or other persons General safety guidelines ● No operator serviceable parts inside. Refer servicing to qualified service personnel. ● Turn off the printer, using both Branch Circuit Breakers located in the building's Power Distribution Unit (PDU), and call - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 6
HP Support to remove and replace the RCCB. ● If the RCCB trips, this indicates it is working correctly, return the printer to the original status and switch the printer curing subsystems of the printer operate at high temperatures. Call your service representative if the printer's built-in Residual - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 7
them. However, HP recommends that you wear gloves when handling ink cartridges or printhead cleaner rolls. Warning and Cautions The following symbols are used in this manual to ensure the proper use of the printer and to prevent the printer from being damaged. Follow the instructions marked with - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 8
energized may represent a hazard during servicing. Refer servicing to qualified service personnel. Turn off the printer using both Branch Circuit Breakers located in the building's Power Distribution Unit (PDU) before servicing. See installation instructions before connecting to the supply. Danger - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 9
back and forth across the substrate. Beware of this moving part. Emergency stop buttons There are four emergency stop buttons distributed around the printer. If an emergency occurs, simply push one of the emergency stop buttons to stop all printing processes. A system error message is displayed on - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 10
procedures for the installation process. This guide is organized in chronological order and should be followed from beginning to end. Manpower required Installation of your HP Scitex LX820/LX850 Printer requires the following manpower: ● HP Installation Specialist ● Customer ● Certified electrician - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 11
Maintenance and troubleshooting guide ● Operating System Recovery CD ● Pneumatic gun ● 2 spindles (the front spindle is mounted on the printer with ties, the rear spindle is attached to the pallet) ● 1 empty substrate core ● Spindle Supports ● 2 Diverters ● Media Loading Tool ● Printheads ◦ HP LX610 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 12
includes 200V, 240/230V, 220V, 127V/120V and 115V/100V/110V ● Two electrical cabinet keys ● Two keys for the lockable covers ● Printer Cleaning Kit ● Maintenance Kit ◦ 2 aerosol filters ◦ 1 printhead cleaner roll ● Purge kit ◦ 7 syringes and needles (extra syringe/needle set is included) ◦ 6 purge - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 13
3 Receive the shipment Unload the crate Manpower 2 persons Tools Forklift, skates Time 15 minutes WARNING! The crate must be lifted with a forklift from the front side of the crate. The front side of the crate will be marked Front. This is important because of the weight distribution inside the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 14
Time 40 minutes NOTE: Approximately 16 bolts and 100 Phillips screws secure the crate. In some cases, it may be necessary to leave the printer inside the crate packaging to go up ramps or make second story deliveries. Plan accordingly. 1. Beginning with the top, left corners, remove the Phillips - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 15
support beams do not fall into the crate. 3. Use a Phillips screwdriver to remove the remaining screws that secure the side panels. 4. Carefully remove the panels and open the plastic bag surrounding the printer and free it from the printer. Remove the printer covers. 3. LX850 only: Remove - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 16
up and the sliding door is secured with the tape used for transportation. 9. Locate the forklift guides underneath the printer and make sure that the forks on the forklift are spaced 80 cm apart (A). 10. Carefully lift the printer, move it away from the pallet and set it on the floor. NOTE: The - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 17
any other crane attachment must be supplied by the customer. For the exact specifications of the crane attachments, see the Site Preparation Guide. WARNING! When lifting the printer with a crane, extra caution should be taken to ensure that the cables do not apply pressure to the center covers or - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 18
perform the following tasks: ● Print ● Use the HP Internal Print Server ● Replace a substrate roll ● Service the printer or replace printer components ● Ensure the printer is well ventilated The printer has the following dimensions: Printer HP Designjet LX850/LX820 Length 5.7 m (18 ft, 11 inches - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 19
Measurement A 8m (26ft 3 in) B 1.5 m (5ft) C 0.6 m (2 ft) minimum D 4 m (13 ft, 2 in) E 1.5 m (5 ft) F 1.5 m (5 ft) WARNING! The zone surrounding the printer should be considered a restricted access area and sign posted accordingly. Only trained personnel should be operating within this - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 20
Tools Cutting Pliers, Allen keys, T20 and T25 screwdrivers Time 15 minutes 1. From the back, remove the electrical cabinet straps and foams from the printer. 2. Remove the straps from the sliding doors. NOTE: The keys to the electrical cabinet are located on top of the cabinet. 16 Chapter 4 Set - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 21
screws attaching the scan path assembly to the frame could seriously damage the printer. NOTE: The screws located at the back, are less accessible and the keys and keep in a safe place. Only the trained operator of the printer must have access to these keys. 5. Remove tape from the window and open - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 22
the service station. 7. Remove the four foam pieces that secure the top cover. 8. Remove the two T20 screws securing the printhead cleaning assembly. 9. Remove the substrate pressure handle straps (pinches). 10. Remove the plastic ties securing the diverter. 18 Chapter 4 Set up the printer in - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 23
11. Remove the plastic tie securing the spindle and the tape covering the air valve. 12. Remove the ink system compartment strap from the printer. 13. Remove the plastic coverings from the ink cartridge connectors. 14. Remove the intermediate tank plastic bags, foams and straps. 15. Remove the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 24
rear beam structure. 23. Remove 4 plastic ties from the left side cover. 24. Remove plastic ties from the top covers. 20 Chapter 4 Set up the printer in the final position ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 25
to unlock the nut at the top of the foot. 2. Rotate the nut manually down the bolt. Leave about 0.8 inches (2 cm) of clearance at the off the ground, tighten the 30 mm locking nut against the printer structure NOTE: The right side of the printer is heavier than the left side. Therefore, the feet on - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 26
Configuration Minimum cross-sectional area High-voltage systems 4 Wires, L1/L2/L3/PE AWG6, 16mm2 High-voltage systems AWG6 The power cord enters into the printer through an entrance in the right top cover and clamped to the side to avoid moving parts. 22 Chapter 5 Connect the power cables ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 27
Tri-phase Power Cord attachment 1. The Tri-phase AC power cord must be attached to the back of the Main Switch. ENWW Tri-phase AC Power Cord 23 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 28
2. Back of the Main Switch is shown below: This Main Switch is made by two blocks of identical size, each one having three contacts. The left block is dedicated to tri-phase lines, so the three contacts are used. The block on the right side is dedicated to single-phase lines, so only two contacts - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 29
on Switch L3 Blank L0 N Wire Phase - Phase Neutral Power Cord Tri-phase - Single-phase Single-phase Protective Earth conductors (grounding) The printer must be connected to a good quality, dedicated ground line in order to avoid electrical risk. Please note your obligation to comply with the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 30
Protective Earth attachment ▲ The ground wires coming from the tri-phase power cord and from the single-phase power cord must be fitted with round terminals suitable for attaching into M6 pillar terminal. Reliable screw attachment must be used. They are close to Protective Earth (PE) terminal - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 31
the electrical system Install the fuses and power jumper Manpower 1 person Time 5 minutes NOTE: The electrical system inside the printer must be configured by the service engineer during installation. CAUTION: If there are any doubts regarding the proper installation of the fuse or power jumper - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 32
configuration Manpower 1 person Tools T10 and M15 screwdriver, M7 wrench Time 5 minutes There are two Delta/Star terminal blocks located on the printer that must be configured. Use the following table to make the configuration, and follow the procedures below to access the two terminal blocks - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 33
Delta configuration1 Star configuration2 1 Use the delta configuration for tri-phase power supply voltages from 200-220 V (between phases). 2 Use the star configuration for tri-phase power supply voltages from 380-415 V (between phases). Heating Module Configuration 1. Remove the six T10 screws - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 34
Curing Module Configuration 1. Remove all the T10 screws securing the right cover of the curing module and remove the cover. TIP: The heating module cover you must remove is marked with orange tape. 2. There is a strap that does not allow you to remove the terminal block. Remove this strap, taking - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 35
mains using the appropriate connectors or by wiring them directly to the PDU, according to the National Electrotechnical Code (NEC). For more information about the printer's electrical specifications, see the Site Preparation Guide. ENWW Check connections 31 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 36
Power on the printer Manpower 1 person Time 5 minutes Ground check 1. Check that the Protective Earth Conductor for the single-phase and tri-phase (green-and-yellow grounding cable) is - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 37
4. Check that the Protective Bonding Conductor (green-and-yellow grounding cable) is well attached to the input single-phase filter. 5. Check the cable behind the tri-phase line filter, towards the middle right of the printer. ENWW Power on the printer 33 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 38
6. Check that the Protective Bonding Conductor (green-and-yellow grounding cable) is well attached to the printer structure. 7. Check that the Protective Bonding Conductor (green-and-yellow grounding cable) is well attached to the drying system (at the resistor connection). 34 Chapter 6 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 39
Conductor (green-and-yellow grounding cable) is well attached to the curing system (at the resistor connection). Turn power on 1. Make sure that the printer is ready to be turned on. Make sure that the emergency stop buttons are not pressed. Make sure the ACB-1, ACB-2 and ACB-3 circuit breakers - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 40
, while it is marked 'initializing', press on OK or Cancel key to continue. If no key is pressed, the printer will stay in this 'initializing' status. When you first turn on the printer, you must set the voltage according to the country of installation. Configure the voltage 1. From the front panel - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 41
no air can be tolerated. From the purging port to the printhead, the printer can tolerate a cumulative total of 20 cm of air (the length of color. Small pockets of bubbles are acceptable. CAUTION: To avoid damaging the printer, do not force any tube or connection. Gently manipulate the syringe during - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 42
panel, select Purge and Setup Menu > Purge ISM. 8. Select the color you want to purge. Ink Supply Legend ● 1=K ● 2=Y ● 3=C ● 4=M ● 5 = LM ● 6 = LC NOTE: The printer starts up the procedure, which may take a couple of minutes. TIP: Do not press the OK button more than once. 9. Place the cartridge on - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 43
port before the electrovalve closes. NOTE: The printer will beep during these 200 seconds. 12. ISS Electrovalves diagnostic procedure described in the Service Manual. While the test is in progress, tap with the syringe and try to identify possible problems. CAUTION: Never look away from the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 44
Ink Supply Legend ● 1=K ● 2=Y ● 3=C ● 4=M ● 5 = LM ● 6 = LC CAUTION: Do not push the ink from the syringe if the electrovalves are not open. You will notice too much resistance if the electrovalves are not open. TIP: If you run out of ink in the syringe, you can refill the syringe from the ink - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 45
22. The printer checks the pressure sensors. If the pressure is correct, press OK to continue. If the pressure sensor value is below the limits or is negative then follow the steps in Problems with the ink sensor value on page 42. 23. Enter the quantity of ink you extracted from the ink - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 46
with the ink sensor value 1. There are three different cases that can cause a problem. ● The pressure sensor value is below a limit, which may vary depending on the volume of the supply. Probably there is an air bubble inside the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 47
2. If the pressure is positive, probably there is an air bubble inside the cartridge connector tube column. Prepare the syringe again, then press OK. 3. Insert the same syringe into the ink cartridge and fill it with 20 cc of ink for the color selected. 4. Check that there is no air in the syringe - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 48
resistance, stop pushing the ink with the syringe and try to identify possible problems. CAUTION: Never look away from the syringe. If you need to perform the 4.5 ISS Ink Pressure Sensors diagnostic procedure found in the Service Manual. Fill the intermediate ink tanks 1. From the front panel, - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 49
that they are installed from the front panel. The printer unfolds the intermediate ink tanks. This process takes approximately 25 minutes. NOTE: During this time, you can install the printhead cleaner roll, aerosol filters, HP Internal Print Server and switch. See Install the printhead cleaning - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 50
away from each other. 8. Make sure the quick connector is placed in the holding panel. 9. Press OK to start the purge. At this point, the printer sends ink to the carriage. This process takes approximately 5 minutes. 46 Chapter 7 Purge the ink system ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 51
each color arrived to the air purger. 11. If ink did not reach one of the air purgers, use a syringe to complete the operation. For instructions, see Use a syringe to purge the tubes from the ISM to the printheads on page 48. 12. Wear gloves and use a cloth to remove the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 52
performs a complete system check during start up. If a failure is detected during start up, follow the troubleshooting instructions in the Service Manual. 18. When the printer finishes initializing, select the preferred language in the front panel. Use a syringe to purge the tubes from the ISM - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 53
NOTE: If the syringe plunger does not move at all, pull it out no more than 1 mm. Otherwise, never manually pull the syringe plunger out. 6. When the purge operation is finished, put a cloth around the needle and remove the syringe quickly. NOTE: Wait until the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 54
the printhead cleaning roll, open the door on the front right of the printer. 2. Grip the handle and pull the whole printhead cleaning roll assembly out and dispose of the roll with the used cleaning material according to the instructions provided with the new roll. Keep the empty core to use as a - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 55
about clearing a printhead cleaning roll jam. Pull the whole assembly out, wind a little of the roll forward, then slide it back in again. The printer will check the roll again 9. Restore the pinch system by moving the black knob back into place. If you feel resistance because the cleaning roll - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 56
of the bottom of its container and dispose of it according to the instructions provided with the new filter. 5. Unpack the new filters and ensure process and are ready to start the printer, select Check cleaner roll from the Ink System menu in normal printer mode. Install the computer, monitor, - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 57
will damage the cables. Cables wrongly positioned: hanging over the sliding door support Cables correctly positioned: supported above the sliding door support 3. Use a T20 screwdriver to remove the monitor holder on the printer. 4. Remove the Phillips screws that secure the monitor arm and remove - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 58
HP switch provided with the printer and the rest of the customer's network. The HP Procurve 1400-8G switch that is included with the printer supports to the HP Internal Print Server computer using the administrative user account that is already set up on the computer. ● HP Designjet LX820/LX850: User - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 59
. 5. Make sure that Share this folder is selected. 6. Set the other settings to your requirements, then click on Permissions. ENWW Create a shared folder on the HP Internal Print Server computer 55 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 60
and Internet > Network and Sharing Center and click on 'Change advance sharing settings'. 9. Make sure that: ● Network discover is turned on ● File and printer sharing is turned on ● Public folder sharing access is turned on ● Password protected sharing is turned off 56 Chapter 8 Prepare the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 61
Configure the printer's IP address If a proxy setting is to be used, make sure that the proxy settings are correctly configured as shown below. Configure the proxy 1. In Internet Explorer, select Tools > Internet options > Connections > LAN settings. ENWW Configure the printer's IP address 57 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 62
site (the IT administrator needs to give all the details). With a proxy service configured (for internet access for example), then: ● Use a proxy server desktop. 2. Set the printer IP address in the Internal Print Server, under Tools > Preferences. 3. Configure HP Proactive Support and make sure the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 63
1 person Time 5 minutes After the initial power up of the printer in normal boot mode, the printer recognizes that the printheads are not installed. Use the following procedure to install the printheads and also follow the instructions on the front panel. 1. At the front panel, select the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 64
servicing. 6. Shake the printhead according to the instructions on the packaging. 7. Put the new printhead into its correct place in the printer , try the following recommendations. 1. Use the procedures in the Service Manual, described under "Large ink area missing or substantial horizontal banding - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 65
the Remote Support Calls to the Support Agent (HP or Authorized Service Provider approved to provide this Remote Support Service). 1. Go supporting this printer, using the reseller's domain used for creating the account. ● If the reseller is not entitled to use the "Callme@hp" remote troubleshooting - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 66
3. Launch the "callme@HP" application under the "tools" menu option and verify the information entered loads correctly into the template. Important: The application will ask for software to be - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 67
including the following text in the comment box: "Customer Name Installation Call. Remote Support Configuration Check". Antivirus Registration Antivirus software is pre-installed with the PC equipment. and it's a requirement for the use of the Callme@HP tool. ENWW Antivirus Registration 63 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 68
the Web cam. Load a substrate For information regarding loading and handling substrates, see the User's Guide. Connect the air supply 1. Locate the airgun and adaptor that was included with the printer shipment. 2. The customer should have the correct air supply with the correct connection. Use the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 69
the same as the IPS PC, refer to Configure the proxy on page 57. HP Scitex Onyx RIP The HP Scitex Onyx RIP is sold with the HP Scitex LX820/LX850 Printer. After the RIP software has been installed and the printer has been added to the RIP, use the following procedure to configure the RIP - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 70
Click Test to check that it responds. 4. Click OK to confirm the printer configuration. HP Scitex Caldera RIP The HP Scitex Caldera RIP is sold with the HP Scitex LX820/LX850 Printer. After the RIP software has been installed and the printer has been added to the RIP, use the following procedure to - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 71
Install the covers Manpower 1 person Tools T30 screwdriver Time 5 minutes NOTE: The covers are wrapped in plastic, and the screws are inside the packaging. It is recommended to install the covers last, in case of any issue that may require you to remove the covers. It is recommended to wear - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 72
location: C:\Users \scitexlx\Documents\HP IPS\Test Plot\Ripped Photorealistic: Make sure before printing the files that the printer is ready to print at its best. 1. Load the correct roll of substrate. 2. Align the printheads (see the Maintenance and Troubleshooting Guide). 3. Check the printhead - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 73
5. Perform Dynamic Color Calibration (refer to the Maintenance & Troubleshooting Guide for more details). 6. Print the three ripped files provided, using the Internal Print Server. or five passes. NOTE: The option of five passes is not available with the HP Photorealistic substrate. ENWW Print the - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 74
45 minutes The following procedure must only be performed in Japan and Russia. 1. Power up the HP Internal Print Server computer. 2. Choose the language for Windows Vista. TIP: Remember that the HP Internal Print Server software will automatically be installed in the language you choose for Windows - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 75
3. Click on Update my score. Change the power settings 1. Select Control Panel > Hardware and Sound > Power Options. ENWW 71 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 76
Screen Saver. TIP: The Screen Saver Settings window is also available under Control Panel > System and Maintenance > Performance Information and Tools. 72 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 77
2. In the Screen Saver drop down menu, select Blank. Configure the hard disk 1. Select Start > Computer > (Right click) Manage > Device Manager >Disk drives > HDD >Properties > Policies (tab). 2. Check the following: ● Optimize for performance ● Enable write caching on the disk ● Enable advanced - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 78
>Performance > Visual Effects > Custom. 2. Only the following should be checked: ● Enable Desktop composition ● Enable transparent glass ● Smooth edges of screen fonts 74 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 79
the site (the IT administrator needs to give all the details). With a proxy service configured (for internet access for example), then: ● Use a proxy server...' is , and type the IP address of the printer, within the 'Exceptions' area. Here is an example of a printer with IP 10.0.0.190: ENWW 75 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 80
follow the on-screen instructions. 2. From the Internal Print Server, navigate to Tools > Preferences and set the printer IP address in the Internal Print Server. 3. From the Internal Print Server, navigate to Tools > Proactive support. Configure the HP Proactive Support and make sure the customer - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 81
not able to automatically retrieve an IP address. In this case, you must manually configure the IP address. Use the following procedure to manually configure the IP address for the printer. 1. Select the setup menu icon . 2. Select Connectivity. 3. Select Gigabit Ethernet. 4. Select View Information - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 82
5. Select TCP/IP. 6. Select IPV4 Settings. 7. Select Config Method. 8. Select Manual to change the configuration so the printer uses the manual settings. 9. From the IPV4 Settings menu, select Manual Settings. 78 Appendix B Manually configure the printer's IP address ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 83
10. Select IP Address to edit the settings. 11. Edit the IP address settings and press OK when you are finished. ENWW 79 - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 84
C Change the Windows Vista language 1. Navigate to the Control Panel on the Internal Print Server and select Clock, Language, and Region. 80 Appendix C Change the Windows Vista language ENWW - HP Scitex LX820 | HP Scitex LX850 & LX820 Printer: Installation Guide - Page 85
2. Select the appropriate entry from the format list. ENWW 81
Scitex LX850 & LX820 Printers
Installation guide