HP Scitex LX850 HP Scitex LX850 & LX820 Printer: Installation Guide - Page 55

Install the aerosol filters

Get HP Scitex LX850 PDF manuals and user guides View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

7. There is a strip of polyester film on the leading edge of the cleaning material. Insert it into the hole in the takeup core, which takes hold of it. 8. Slide the takeup core onto the lower axle. It clicks into place. NOTE: If the cleaner roll has not been properly installed, you may see a message about clearing a printhead cleaning roll jam. Pull the whole assembly out, wind a little of the roll forward, then slide it back in again. The printer will check the roll again 9. Restore the pinch system by moving the black knob back into place. If you feel resistance because the cleaning roll is too tight, turn the roll slightly counter-clockwise. 10. Grip the handle and push the whole printhead cleaning roll assembly back into the printer. 11. Close the door. Install the aerosol filters 1. Open the printhead access door in the side of the printer, and lift the carriage cover. 2. The aerosol filter containers are on the near and the far sides of the printheads. ENWW Install the printhead cleaning roll and aerosol filters 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
7.
There is a strip of polyester film on the leading edge of the cleaning material. Insert it into the hole
in the takeup core, which takes hold of it.
8.
Slide the takeup core onto the lower axle. It clicks into place.
NOTE:
If the cleaner roll has not been properly installed, you may see a message about clearing
a printhead cleaning roll jam. Pull the whole assembly out, wind a little of the roll forward, then slide
it back in again. The printer will check the roll again
9.
Restore the pinch system by moving the black knob back into place. If you feel resistance because
the cleaning roll is too tight, turn the roll slightly counter-clockwise.
10.
Grip the handle and push the whole printhead cleaning roll assembly back into the printer.
11.
Close the door.
Install the aerosol filters
1.
Open the printhead access door in the side of the printer, and lift the carriage cover.
2.
The aerosol filter containers are on the near and the far sides of the printheads.
ENWW
Install the printhead cleaning roll and aerosol filters
51