HP StorageWorks 1000s NAS 1000s - Quick Start Guide - Page 31

Remote Access Method Using Hostname

Get HP StorageWorks 1000s - NAS PDF manuals and user guides View all HP StorageWorks 1000s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Remote Access Method (Using Hostname) The NAS 1000s ships by default with DHCP enabled on the network port. If the system is placed on a DHCP serviced network and the serial number of the device is known, it can be accessed through a client running Microsoft Internet Explorer 5.5 (or later) on that network, using the 3201 port of the device. The serial number is located on the product ID label. Requirements The following items are required to run the WebUI configuration application: ■ Windows-based PC loaded with Internet Explorer 5.5 (or later) on the same segment as the NAS 1000s ■ DHCP-serviced network ■ Serial number of the NAS 1000s Note: The NAS 1000s is designed to be deployed without a monitor, keyboard, and mouse. These ports are available and supported by the NAS device, if used. Procedure To initialize the NAS 1000s using the WebUI configuration application: 1. Connect the Ethernet cables to the respective network ports of the NAS b2000 v2 and the corresponding network segments in accordance with the information in the "Configuration Information" section in Chapter 2. 2. See Figure 3 and Table 4 for the locations of the network ports on the NAS 1000s. 3. Go to the NAS device and power it on. It will be several minutes before the NAS device is accessible on the network. NAS 1000s Quick Start Guide 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
NAS 1000s Quick Start Guide
31
Remote Access Method (Using Hostname)
The NAS 1000s ships by default with DHCP enabled on the
network port. If the system is placed on a DHCP serviced
network and the serial number of the device is known, it can be
accessed through a client running Microsoft Internet Explorer 5.5
(or later) on that network, using the 3201 port of the device. The
serial number is located on the product ID label.
Requirements
The following items are required to run the WebUI configuration
application:
■
Windows-based PC loaded with Internet Explorer 5.5 (or
later) on the same segment as the NAS 1000s
■
DHCP-serviced network
■
Serial number of the NAS 1000s
Note:
The NAS 1000s is designed to be deployed without a monitor,
keyboard, and mouse. These ports are available and supported by the
NAS device, if used.
Procedure
To initialize the NAS 1000s using the WebUI configuration
application:
1.
Connect the Ethernet cables to the respective network ports
of the NAS b2000 v2 and the corresponding network
segments in accordance with the information in the
“Configuration Information” section in Chapter 2.
2.
See
Figure 3
and
Table 4
for the locations of the network
ports on the NAS 1000s.
3.
Go to the NAS device and power it on. It will be several
minutes before the NAS device is accessible on the network.