HP StorageWorks 2/32 HP StorageWorks SAN Switch Rack Mount Kit Installation In
HP StorageWorks 2/32 - SAN Switch Manual
 |
View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 2/32 manual content summary:
- HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 1
HP StorageWorks SAN Switch rack mount kit installation instructions Sixth Edition (May 2007) *A7511-90902* Part Number: *A7511-90902* - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 2
this document is subject to change without notice. BROCADE, the Brocade B weave logo, Brocade: the Intelligent Platform for Networking Storage, SilkWorm, in the U.S.A. SAN Switch rack mount kit installation instructions Sixth Edition (May 2007) Part Number: *A7511-90902* 2 SAN Switch rack mount - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 3
(SAN) switches and routers. Supported Devices Use the SAN Switch Rack Mount Kit to install the following HP StorageWorks switches and routers only: ■ SAN Switch 2/8V, SAN Switch 2/16V ■ SAN Switch 2/32 ■ SAN Switch 4/32 ■ 4/8 SAN Switch ■ 4/16 SAN Switch ■ 4/64 SAN Switch ■ 4/32B SAN Switch ■ Multi - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 4
plenum ships with the following devices only: ■ SAN Switch 2/8V ■ SAN Switch 2/16 ■ SAN Switch 2/16V ■ 4/8 SAN Switch ■ 4/16 SAN Switch ■ 4/32B SAN Switch See Installing the Plenum (if required), page 17 for complete instructions on how to install a plenum. 4 SAN Switch rack mount kit installation - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 5
inches (68.6 cm) deep. For the MP Router or 4/64 SAN Switch, plan a rack space that is at least 2 units high. ■ Ground all equipment in the rack through a reliable branch circuit connection, and maintain ground at all times. Do not rely on a secondary connection to a branch circuit, such as a power - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 6
the following items: ■ #2 Phillips screwdriver ■ 7/16-inch wrench or socket ■ HP StorageWorks device, see Supported Devices on page 3 ■ Plenum (if required), see Before You Begin - Important Information about the Plenum, page 4 ■ Power cables ■ SAN Switch Rack Mount Kit hardware (smaller items like - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 7
SEMS screws Ten (10) #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers Eight (8) #10 alignment washers Eight (8) #10 adapter washers Two (2) 1/4-20 hex nuts with captive star lock washers Two (2) 1/4-inch flat washers SAN Switch rack mount kit installation instructions 7 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 8
, assemble each of the two brackets with two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 adapter washers as shown in Figure 1. Figure 1: Installing the Rear Mounting Brackets (HP 10000 Series Racks) 8 SAN Switch rack mount kit installation instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 9
each of the two rear mounting brackets with two #10-32 x 1/2-inch Phillips pan-head screws and two #10 alignment washers as shown in Figure 2. Figure 2: Installing the Rear Mounting Brackets (HP System/e Rack) Note: Your SAN Switch Rack Mount Kit contains both left rails and right rails. The - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 10
using two 1/4-20 hex nuts with captive star lock washers. Attach the hex nuts loosely (as shown in Figure 3). Do not tighten; tighten the hex nuts later in step 3 on page 19. Figure 3: Installing the Outer Rails (HP 10000 Series Racks) 10 SAN Switch rack mount kit installation instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 11
#10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 adapter washers in the upper and lower hole locations of the left rail, as shown in Figure 4. Figure 4: Assembling the Outer Rails (HP 10000 Series Racks) SAN Switch rack mount kit installation instructions 11 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 12
two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 alignment washers in the upper and lower hole locations of the left rail, as shown in Figure 5. Figure 5: Assembling the Outer Rails (HP System/e Rack) 12 SAN Switch rack mount kit installation instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 13
#8-32 x 3/16-inch Screws SAN Switch 2/16, SAN Switch 2/8V, or SAN Switch 2/16V Ten (Five per rail) N/A SAN Switch 2/32 N/A 12 (Six per rail) MP Router Six (Three per rail) N/A SAN Switch 4/32 Ten (Five per rail) N/A 4/8 and 4/16 SAN Switch Ten (Five per rail) N/A 4/64 SAN Switch - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 14
to the SAN Switch 4/32, 4/32B SAN Switch, 4/64 SAN Switch or the 400 MP Router use the screw holes marked 16. Caution 64 SAN Switch with five screws using the rail screw holes marked 16. Please note that attaching both rails require ten screws. 14 SAN Switch rack mount kit installation instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 15
-63 Hz DC OK AC OK Figure 6: Attaching the Inner Rails to an MP Router MRO25007a ! IOIOI SPD LNK Figure 7: Attaching the Inner Rails to a 4/64 SAN Switch SAN Switch rack mount kit installation instructions MRO25018b 15 - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 16
#8-32 x 3/16-inch Phillips pan-head screw with thread lock and torque between 6 to 8 inch-pounds. 8. If installing one of the following switches, you must install the plenum that ships in the accessory kit with the rack mount hardware: ■ SAN Switch 2/8V ■ SAN Switch 2/16 ■ SAN Switch 2/16V ■ 4/8 SAN - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 17
the plenum and four 8-32 x .312 Phillips switch (2), and the screws that attach the rails to the plenum (3). 1 2 IOIOI ! 3 mMAoaTuxTnimtEinugmNtoTscbIrOeew5Nmle:mngothr 1fo3r/6ra4cikn. Figure 8: Attaching the Plenum to a 4/8 or 4/16 SAN Switch SAN Switch rack mount kit installation instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 18
the device into the rack and install (2) #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers with one on each side. See Figure 9 and Figure 10. Figure 9: Securing the Device (in HP 9000 Series or HP 10000 Series Racks) 18 SAN Switch rack mount kit installation instructions - HP StorageWorks 2/32 | HP StorageWorks SAN Switch Rack Mount Kit Installation In - Page 19
in step 4 on page 10. See Figure 3. Note: To uninstall a device, remove the middle #10-32 x 1/2-inch Phillips pan head screw with captive star lock washer from either side of the rack uprights. This completes the rack mount procedure. SAN Switch rack mount kit installation instructions 19
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
 |
 |
HP StorageWorks
SAN Switch
rack mount kit
installation instructions
Sixth Edition (May 2007)
*A7511-90902*
Part Number:
*A7511-90902*