HP Surestore 2200mx HP SureStore 220mx Optical Jukebox User's Guide - Page 21

Connecting the Jukebox as the Only, Peripheral

Get HP Surestore 2200mx PDF manuals and user guides View all HP Surestore 2200mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Setting Up the Jukebox NOTE NOTE Setting up the Jukebox Connecting the Jukebox as the Only Peripheral Connecting the Jukebox as the Only Peripheral The default IDs for the jukebox are as follows. Check to see if there will be any conflicts in this installation. Autochanger (jukebox robotics) = 3 Drive 1 = 4 Drive 2 = 5 (if installed) If any of the autochanger/drive IDs are already being used, you can either change IDs used by the host bus adapter or another device on the bus, or you can change the autochanger/drive IDs. If you choose to change the IDs of devices other than the autochanger and/or drives, do it now (before you begin cabling). Refer to your host and host bus adapter documentation. If you will be changing the IDs of the autochanger or the drives, you will be given an opportunity to do this in the installation steps that follow. 1. Ensure that the mailslot shipping bracket and the shipping screw are removed. If you will be changing SCSI IDs in the host, finish changing them before doing the next step. See the previous NOTE. 2. Ensure that your host computer is OFF and the jukebox standby/on switch is in the STANDBY position. The jukebox standby/on switch is in STANDBY when the STANDBY side of the switch is depressed. The switch is shown by "2" on Figure 1-1. Chapter 1 1- 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Chapter 1
1-9
Setting up the Jukebox
Connecting the Jukebox as the Only Peripheral
Setting Up the Jukebox
Connecting the Jukebox as the Only
Peripheral
The default IDs for the jukebox are as follows.
Check to see if there will be
any conflicts in this installation.
Autochanger (jukebox robotics) = 3
Drive 1 = 4
Drive 2 = 5 (if installed)
NOTE
If any of the autochanger/drive IDs are already being used, you can
either change IDs used by the host bus adapter or another device on the
bus, or you can change the autochanger/drive IDs.
If you choose to change the IDs of devices
other
than the autochanger
and/or drives,
do it now
(before you begin cabling). Refer to your host and
host bus adapter documentation.
If you will be changing the IDs of the autochanger or the drives, you will
be given an opportunity to do this in the installation steps that follow.
1.
Ensure that the mailslot shipping bracket and the shipping screw are
removed.
NOTE
If you will be changing SCSI IDs in the host, finish changing them before
doing the next step. See the previous NOTE.
2.
Ensure that your host computer is OFF and the jukebox standby/on
switch is in the STANDBY position.
The jukebox standby/on switch is in STANDBY when the STANDBY
side of the switch is depressed. The switch is shown by
“
2
”
on
Figure 1-1.