HP Vectra XU 6/XXX HP Vectra XU 6/xxx Pc User’s Guide - d4369-90001 - Page 20

Connecting a SCSI Accessory

Get HP Vectra XU 6/XXX PDF manuals and user guides View all HP Vectra XU 6/XXX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

1 Setting Up Your PC Connecting a SCSI Accessory Connecting a SCSI Accessory Note that Ultra SCSI mode is disabled automatically when an external SCSI accessory is connected to your PC. To learn how to enable Ultra SCSI even when an external SCSI device is connected, see "Configuring the SCSI Interface" on page 96. 1 Refer to the manual provided with the SCSI accessory for instructions on selecting a SCSI address. You should assign an unused SCSI address to the accessory. SCSI addresses range from 0 to 7, with SCSI address 0 used by the first SCSI hard disk drive and SCSI address 7 reserved for the integrated SCSI controller. NOTE You don't need to set a SCSI address for Plug and Play SCSI devices (SCSI devices which support the SCAM protocol). 2 Connect the SCSI accessory to your PC's external SCSI connector with a shielded SCSI cable. (Note that Ultra SCSI is automatically disabled when an external SCSI accessory is connected.) SCSI 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
1
Setting Up Your PC
Connecting a SCSI Accessory
8
Connecting a SCSI Accessory
Note that Ultra SCSI mode is disabled automatically when an external
SCSI accessory is connected to your PC. To learn how to enable Ultra
SCSI even when an external SCSI device is connected, see “Configuring
the SCSI Interface” on page 96.
1
Refer to the manual provided with the SCSI accessory for
instructions on selecting a SCSI address. You should assign an
unused SCSI address to the accessory. SCSI addresses range from 0
to 7, with SCSI address 0 used by the first SCSI hard disk drive and
SCSI address 7 reserved for the integrated SCSI controller.
NOTE
You don’t need to set a SCSI address for Plug and Play SCSI devices
(SCSI devices which support the SCAM protocol).
2
Connect the SCSI accessory to your PC’s external SCSI connector
with a shielded SCSI cable. (Note that Ultra SCSI is automatically
disabled when an external SCSI accessory is connected.)
SCSI