Home » HP Manuals » Desktops » HP Visualize c3000 » Manual Viewer

HP Visualize c3000 hp Visualize b1000 and c3000 workstations service handbook - Page 125

Warning, Caution

Get HP Visualize c3000 - Workstation PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Field Replaceable Units FRU Removal and Replacement cover's edge is rounded to keep you from cutting the cables. Figure 4-34. Next, place the end opposite the rear cover handle into the cover slot and tighten the T-15 Torx screw to secure the rear cover. You have now completed the removal of the CD Drive. Figure 4-34. Replacing the CD Drive Rear Cover Rear Cover Rear Cover Handle Audio Cable ATAPI Cable T-15 Torx/slotted Screw Power Cable Installing a Floppy Disk Drive Install the floppy disk drive by following the procedure covered in this section. Note there are no jumper settings required for the installation of the floppy disk drive. WARNING Turn the workstation off and unplug the power cord before installing the floppy disk drive. CAUTION Floppy disk drives are susceptible to mechanical and electronic shock. When handling the drive, always wear the static-grounding wrist strap that came in the Floppy disk drive kit. Always handle the drive carefully. 1. Perform the procedures in the sections "Opening the System Unit Front Panel" and "Opening the Left Side Panel of the System Unit." The front panel needs to be opened so you can insert the floppy disk drive into its proper location in the chassis. The left side panel needs to be opened to access the floppy's data connector and its power connector. 2. Remove the floppy rear-disk cover by unscrewing the T-15 Torx screw as shown in Figure 4-35. Note that the floppy's rear cover is located on the rear of the removable media chassis inside the system unit. Push the cover handle away from the rear of the removable media chassis approximately one inch. Next pull the cover handle toward you. The data and power cables are now accessible to you. Chapter 4 125

Section	Page
Service Handbook	1
Service Handbook	1
Service Handbook	1
HP Visualize Workstations	1
Model B1000/C3000	1
Manufacturing Part Number: HP Part No. A4985-90039	1
Printed in USA May 1999	1
Edition E0599	1
Notice	2
Notice	2
The information contained in this document is subject to change without notice. Hewlett-Packard a...	2
Hewlett-Packard Warranty Statement	2
Hewlett-Packard Warranty Statement	2
HP PRODUCT DURATION OF WARRANTY HP Visualize Wo...	2
Model B1000/C3000	2
1. HP warrants HP hardware, accessories and supplies against defects in materials and workmanship...	2
1. HP warrants HP hardware, accessories and supplies against defects in materials and workmanship...	2
1. HP warrants HP hardware, accessories and supplies against defects in materials and workmanship...	2
2. HP warrants that HP software will not fail to execute its programming instructions, for the pe...	2
2. HP warrants that HP software will not fail to execute its programming instructions, for the pe...	2
3. HP does not warrant that the operation of HP products will be uninterrupted or error free. If ...	2
3. HP does not warrant that the operation of HP products will be uninterrupted or error free. If ...	2
4. HP products may contain remanufactured parts equivalent to new in performance or may have been...	2
4. HP products may contain remanufactured parts equivalent to new in performance or may have been...	2
5. The warranty period begins on the date of delivery or on the date of installation if installed...	2
5. The warranty period begins on the date of delivery or on the date of installation if installed...	2
6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or ca...	2
6. Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or ca...	2
7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY O...	3
7. TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO OTHER WARRANTY O...	3
8. HP will be liable for damage to tangible property per incident up to the greater of $300,000 o...	3
8. HP will be liable for damage to tangible property per incident up to the greater of $300,000 o...	3
9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S SOL...	3
9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S SOL...	3
Restricted Rights Legend	3
Restricted Rights Legend	3
Use, duplication, or disclosure by the U.S. Government Department of Defense is subject to restri...	3
Copyright 1999 Hewlett-Packard Company. All Rights Reserved.	3
Copyright 1999 Hewlett-Packard Company. All Rights Reserved.	3
This document contains proprietary information that is protected by copyright. All rights are res...	3
This document contains proprietary information that is protected by copyright. All rights are res...	3
UNIX is a registered trademark in the United States and other countries, licensed exclusively thr...	3
UNIX is a registered trademark in the United States and other countries, licensed exclusively thr...	3
Copyright 1980, 1984 AT&T, Inc.	3
Copyright 1980, 1984 AT&T, Inc.	3
Copyright 1979, 1980, 1983 The Regents of the University of California.	3
Copyright 1979, 1980, 1983 The Regents of the University of California.	3
This software and documentation is based inpart on the Fourth Berkeley Software Distribution unde...	3
This software and documentation is based inpart on the Fourth Berkeley Software Distribution unde...	3
Printing History	4
Printing History	4
New editions of this manual incorporate all material updated since the previous edition. Update p...	4
The manual part number and printing date indicate its current edtion. The manual part number chan...	4
HP Part Number Printing Date Edition	4
A4985-90039 May 1999 First	4
Table of Contents	5
Table of Figures	11
Table of Tables	15
Ch 1 Product Information	17
This chapter introduces the HP Visualize B1000/C3000 workstations, including their controls and i...	17
This chapter introduces the HP Visualize B1000/C3000 workstations, including their controls and i...	17
Included in this chapter are the following topics:	18
Product description	18
Product description	18
Product description	18
Product description	18
System unit front panel controls	18
System unit front panel controls	18
System unit rear panel connectors	18
System unit rear panel connectors	18
Monitor information	18
Monitor information	18
Keyboard and Mouse information	18
Keyboard and Mouse information	18
Operating System Overview	18
Operating System Overview	18
B1000/C3000:product description,	19
B1000/C3000:product description,	19
B1000/C3000:product description,	19
The HP Visualize B1000 and C3000 workstations contain the following key features:	19
The HP Visualize B1000 and C3000 workstations contain the following key features:	19
Processor:	19
Processor:	19
Processor:	19
One 300MHz PA8500 microprocessor in the B1000 workstation	19
One 400MHz PA8500 microprocessor in the C3000 workstation	19
The PA8500 processor has a 0.5MByte instruction cache and a 1.0MByte data cache	19
Operating System:	19
Operating System:	19
Workstations B1000/C3000 require HP-UX 10.20 and Workstation ACE (Additional Core Enhancements) f...	19
User Interface:	19
User Interface:	19
HP CDE graphical user interface	19
Compatibility: Source and binary code compatible with the Series 700 product family	19
Compatibility: Source and binary code compatible with the Series 700 product family	19
Monitors:	19
Monitors:	19
21-inch 1280¥1024 (stereo capability) and 1600¥1200 color, 75Hz	19
Optional Graphics:	19
Optional Graphics:	19
HP Visualize-EG and Visualize fx2 Pro (for B1000)	19
HP Visualize-EG, Visualize fx2 Pro and Visualize fx4 Pro (for C3000)	19
Main Memory:	19
Main Memory:	19
128MByte and 256MByte DIMMs for B1000 and C3000 workstations	19
Eight memory slots available per each B1000 and C3000 workstations	19
Minimum of 128MBytes and a maximum of 2GBytes of memory (B1000 and C3000)	19
Internal Storage Devices:	19
Internal Storage Devices:	19
Wide Ultra2 Low-Voltage Differential SCSI – up to two:	19
9.0 GB Hard Disk Drive	19
18.0 GB Hard Disk Drive	19
Removable Media (one of each maximum)	19
CD-ROM Drive	19
Floppy Disk Drive	19
Standard Network:	19
Standard Network:	19
RJ45, Twisted Pair 10 BaseT/100 BaseT	19
Standard I/O Ports:	19
Standard I/O Ports:	19
Ultra2 Wide Low-Voltage Differential (LVD) SCSI, one	20
Ultra Narrow Single-Ended (NSE) SCSI, one	20
Parallel port (IEEE 1284), one	20
Universal Serial Bus (USB) ports, two	20
Serial Interface ports (RS-232C), two	20
Audio ports (Line-in, Line-out, headset, and microphone-in)	20
Optional I/O:	20
Optional I/O:	20
Six PCI slots are available for the B1000/C3000 workstations.	20
1 PCI 4X:64 bit, 66 MHz, primary graphics (full size, 3.3V)	20
2 PCI 1X:32 bit, 33 MHz, (half size, 5V)	20
3 PCI 2X:64 bit, 33 MHz, (full size, 5V)	20
Keyboard:	20
Keyboard:	20
Universal Serial Bus (USB) keyboard, one	20
Mouse:	20
Mouse:	20
Universal Serial Bus (USB) mouse, one	20
System Unit Front Panel Controls	21
System Unit Front Panel Controls	21
Figure 1-1 shows the location of the system unit front panel controls.	21
Figure 1-1 shows the location of the system unit front panel controls.	21
Figure11. System Unit Front Panel Controls	21
Figure11. System Unit Front Panel Controls	21
<GRAPHIC>	21
LCD:location,	21
LCD:location,	21
The Liquid Crystal Display (LCD) is located on the left side of the front panel. The LCD displays...	21
LCD:symbols,	22
LCD:symbols,	22
LCD:symbols,	22
<GRAPHIC>	22
Power switch:soft power down procedure,	22
Power switch:soft power down procedure,	22
Use the Power switch to power the system unit on and off. When you use the soft power down proced...	22
Storage Device:controls and features,	22
Storage Device:controls and features,	22
Storage Device:controls and features,	22
This workstation allows either or both of the following internal storage devices: CD drive or flo...	22
NOTE You cannot have two internal storage devices of the same type. For example, you cannot have ...	22
NOTE You cannot have two internal storage devices of the same type. For example, you cannot have ...	22
Figure 13.	22
Figure 13.	22
Storage device:CD drive,	23
Storage device:CD drive,	23
Storage device:CD drive,	23
<GRAPHIC>	23
Table11. CD Drive Controls	23
<TABLE HEADING>	23
<TABLE ROW>	23
Control/Feature	23
Control/Feature	23
Purpose	23
Purpose	23
<TABLE BODY>	23
<TABLE ROW>	23
Eject Button	23
Press to open the Disc Tray and insert or remove a disc. When the drive is in use, press the ejec...	23
<TABLE ROW>	23
Emergency Eject	23
Emergency Eject	23
If the workstation does no have power, you can insert the end of a paper clip into this small hol...	23
If the workstation does no have power, you can insert the end of a paper clip into this small hol...	23
<TABLE ROW>	23
Disk Tray	23
Disk Tray	23
The Disk Tray holds the CD. This style of CD drive does not use a disk caddy.	23
The Disk Tray holds the CD. This style of CD drive does not use a disk caddy.	23
<TABLE ROW>	23
Busy Indicator	23
Busy Indicator	23
Lights during a data access operation and blinks during a data transfer. The indicator blinks ini...	23
Lights during a data access operation and blinks during a data transfer. The indicator blinks ini...	23
A defective disc	23
A defective disc	23
A defective disc	23
A disc insertion error (for example, an upside down disc)	23
A disc insertion error (for example, an upside down disc)	23
No disc present	23
No disc present	23
NOTE The audio features of the CD drive are supported through applications only. One such applica...	23
NOTE The audio features of the CD drive are supported through applications only. One such applica...	23
The optional	24
Figure 14.	24
Figure 14.	24
Figure14. Floppy Drive Controls and Features	24
Figure14. Floppy Drive Controls and Features	24
<GRAPHIC>	24
Table12. Floppy Drive Controls and Features	24
<TABLE HEADING>	24
<TABLE ROW>	24
Control/Feature	24
Purpose	24
Purpose	24
<TABLE BODY>	24
<TABLE ROW>	24
Floppy Drive Eject Button	24
Floppy Drive Eject Button	24
Push the eject button to remove floppy diskettes from the drive.	24
Push the eject button to remove floppy diskettes from the drive.	24
<TABLE ROW>	24
Floppy Drive Activity LED	24
Floppy Drive Activity LED	24
The floppy drive LED flashes to indicate the drive is in use.	24
The floppy drive LED flashes to indicate the drive is in use.	24
Security Lock	24
Security Lock	24
Access to the mass storage devices is controlled by a security lock on the front panel. Locking t...	24
To prevent access to internal components requires the use of the security loop on the rear panel ...	24
Rear Panel Connectors:	25
Rear Panel Connectors:	25
Rear Panel Connectors:	25
This section describes the following connectors on the system unit’s rear panel:	25
This section describes the following connectors on the system unit’s rear panel:	25
Two serial ports (RS-232)	25
Two serial ports (RS-232)	25
Two serial ports (RS-232)	25
Two serial ports (RS-232)	25
Two Universal Serial Bus ports (USB)	25
LAN connector, 10 BaseT/100 BaseT	25
LAN connector, 10 BaseT/100 BaseT	25
HP parallel IEEE 1284 (printer) connector	25
Audio connectors (PCI based, line in, line out, headset, and microphone in)	25
Audio connectors (PCI based, line in, line out, headset, and microphone in)	25
Ultra2 Wide LVD (Low Voltage Differential) SCSI	25
Ultra2 Wide LVD (Low Voltage Differential) SCSI	25
Ultra Narrow Single-Ended (NSE) SCSI	25
Ultra Narrow Single-Ended (NSE) SCSI	25
TOC (transfer of control) button	25
TOC (transfer of control) button	25
AC power cord connector	25
AC power cord connector	25
Security loop	25
Security loop	25
NOTE To maintain FCC/EMI compliance, verify that all cables are fully seated and properly fastened.	25
NOTE To maintain FCC/EMI compliance, verify that all cables are fully seated and properly fastened.	25
Figure15. System Unit Rear Panel Connectors	25
Figure15. System Unit Rear Panel Connectors	25
<GRAPHIC>	26
Rear Panel Connectors:audio connectors,	26
Rear Panel Connectors:audio connectors,	26
The Model B1000 and C3000 workstations have audio-input and -output capabilities through external...	26
The rear panel contains the Audio IN (Stereo line-in) and Microphone (Mic-in), and Audio OUT (Ste...	26
The audio connectors are standard stereo audio mini-jacks (see Figure 1-6).	26
NOTE Hewlett-Packard recommends using gold-plated plugs available through audio retailers for bes...	26
NOTE Hewlett-Packard recommends using gold-plated plugs available through audio retailers for bes...	26
Figure16. Audio Connectors	26
Figure16. Audio Connectors	26
<GRAPHIC>	26
Table 13.	26
<TABLE>	27
Table13. Audio Electrical Specifications	27
<TABLE BODY>	27
<TABLE ROW>	27
Frequency Response	27
Frequency Response	27
25 to 20KHz	27
25 to 20KHz	27
<TABLE ROW>	27
Input Sensitivity/Impedance	27
Input Sensitivity/Impedance	27
<TABLE ROW>	27
Line in	27
Line in	27
2.0V pk/47kohm	27
2.0V pk/47kohm	27
<TABLE ROW>	27
Microphone in	27
Microphone in	27
22mVpk/1kohm	27
22mVpk/1kohm	27
<TABLE ROW>	27
Max Output Level/Impedance	27
Max Output Level/Impedance	27
<TABLE ROW>	27
Line Out	27
Line Out	27
2.8Vpp/47kohm	27
2.8Vpp/47kohm	27
<TABLE ROW>	27
Headphone	27
Headphone	27
2.75Vpp/50ohm	27
2.75Vpp/50ohm	27
<TABLE ROW>	27
Speaker (internal)	27
Speaker (internal)	27
5.88Vpp/48ohm	27
5.88Vpp/48ohm	27
<TABLE ROW>	27
Output Impedance	27
Output Impedance	27
<TABLE ROW>	27
Line Out	27
Line Out	27
619ohm	27
619ohm	27
<TABLE ROW>	27
Headphone	27
Headphone	27
118ohm	27
118ohm	27
USB:,	27
USB:,	27
USB:,	27
The USB connectors located on the rear panel of the workstation provide an interface for the keyb...	27
The USB connectors located on the rear panel of the workstation provide an interface for the keyb...	27
For more information on the Universal Serial Bus, refer to the following URL:	27
	27
CAUTION Usage of devices other than USB specification may result in unpredictable functionality a...	27
CAUTION Usage of devices other than USB specification may result in unpredictable functionality a...	27
NOTE The USB clip on the rear of the chassis provides strain relief for the USB cables.	27
NOTE The USB clip on the rear of the chassis provides strain relief for the USB cables.	27
Rear Panel Connectors:parallel,	27
Rear Panel Connectors:parallel,	27
Rear Panel Connectors:parallel,	27
The 25-pin HP Parallel I/O interface uses IEEE 1284 I/O interface protocols to support peripheral...	27
The 25-pin HP Parallel I/O interface uses IEEE 1284 I/O interface protocols to support peripheral...	27
Rear Panel Connectors:network,	27
Rear Panel Connectors:network,	27
Rear Panel Connectors:network,	27
The B1000/C3000 workstations have a built-in Twisted Pair (TP) connector for the 802.3 (ETHERNET)...	27
Rear Panel Connectors:serial,	28
Rear Panel Connectors:serial,	28
Rear Panel Connectors:serial,	28
There are a variety of peripheral devices that can attach to the RS-232 Serial Input/Output (SIO)...	28
The SIO ports are programmable, allowing functions such as bit rate, character length, parity, an...	28
Table 14.	28
Table 14.	28
<TABLE>	28
Table14. Serial I/O Pins	28
<TABLE HEADING>	28
<TABLE ROW>	28
Pin No.	28
Pin No.	28
Signal	28
Signal	28
Description	28
Description	28
<TABLE BODY>	28
<TABLE ROW>	28
1	28
1	28
DCD	28
DCD	28
Data Carrier Detect	28
Data Carrier Detect	28
<TABLE ROW>	28
2	28
2	28
RXD	28
RXD	28
Receive Data	28
<TABLE ROW>	28
3	28
3	28
TXD	28
TXD	28
Transmit Data	28
<TABLE ROW>	28
4	28
4	28
DTR	28
DTR	28
Data Terminal Ready	28
<TABLE ROW>	28
5	28
5	28
GND	28
GND	28
Ground	28
Ground	28
<TABLE ROW>	28
6	28
6	28
DSR	28
DSR	28
Data Set Ready	28
Data Set Ready	28
<TABLE ROW>	28
7	28
7	28
RTS	28
RTS	28
Request To Send	28
Request To Send	28
<TABLE ROW>	28
8	28
8	28
CTS	28
CTS	28
Clear To Send	28
Clear To Send	28
<TABLE ROW>	28
9	28
9	28
RI	28
RI	28
Ring Indicator	28
Ring Indicator	28
SCSI:connectors,	28
SCSI:connectors,	28
SCSI:connectors,	28
The B1000/C3000 workstations have built in SCSI connectors for Ultra2 Wide Low-Voltage Differenti...	28
NOTE There must ALWAYS be a terminator at both ends of a SCSI bus. This means one internal termin...	28
NOTE There must ALWAYS be a terminator at both ends of a SCSI bus. This means one internal termin...	28
Rear Panel Connectors:TOC,	29
Rear Panel Connectors:TOC,	29
Rear Panel Connectors:TOC,	29
The TOC (transfer of control) button interrupts the system and transfers control from the default...	29
Rear Panel Connectors:power cord	29
Rear Panel Connectors:power cord	29
Rear Panel Connectors:power cord	29
Plug the workstation’s power cord into the power cord connector to provide AC power to the system.	29
Rear Panel Connectors:security loop,	29
Rear Panel Connectors:security loop,	29
Rear Panel Connectors:security loop,	29
The security loop provides a means of locking the left side panel with a padlock or other locking...	29
1. Inspect left side panel for proper seating in the mainframe chassis.	29
1. Inspect left side panel for proper seating in the mainframe chassis.	29
2. Push in the retractable pin on the spring loaded square fastener.	29
2. Push in the retractable pin on the spring loaded square fastener.	29
3. Insert the locking device through the top and bottom holes of the square fastener.	29
3. Insert the locking device through the top and bottom holes of the square fastener.	29
4. Inspect after locking device is in place to assure that the retractable pin is captured in the...	29
4. Inspect after locking device is in place to assure that the retractable pin is captured in the...	29
The internal components of the workstation is now secured. See	29
NOTE A locking device is not supplied with the workstation; the customer must supply a lock to us...	29
NOTE A locking device is not supplied with the workstation; the customer must supply a lock to us...	29
Figure17. Security Loop Operation	30
Figure17. Security Loop Operation	30
<GRAPHIC>	31
Monitor:,	31
Monitor:,	31
The B1000/C3000 workstations support the following monitors:	31
The B1000/C3000 workstations support the following monitors:	31
19-inch, 1280¥1024 color monitor (A4575A)	31
19-inch, 1280¥1024 color monitor (A4575A)	31
19-inch, 1280¥1024 color monitor (A4575A)	31
19-inch, 1600¥1200 color monitor (A4575A)	31
19-inch, 1600¥1200 color monitor (A4575A)	31
21-inch, 1280¥1024 color monitor (A4576A)	31
21-inch, 1280¥1024 color monitor (A4576A)	31
21-inch, 1600¥1200 color monitor (A4576A)	31
21-inch, 1600¥1200 color monitor (A4576A)	31
For information on the A4575A monitors, see:	31
HP A4575A Color Monitor CE Handbook	31
HP A4575A Color Monitor CE Handbook	31
HP A4575A Color Monitor CE Handbook	31
The A4575A is a 19\	31
For information on the A4576A monitor, see:	31
The A4576A is a 21\	31
NOTE Note that the word “multi-sync” is used as a common word to refer to “multi-frequency” and/o...	31
NOTE Note that the word “multi-sync” is used as a common word to refer to “multi-frequency” and/o...	31
NOTE The connection to earlier HP monitors with 15-pin mini-DSub cables can be made using the A41...	31
NOTE The connection to earlier HP monitors with 15-pin mini-DSub cables can be made using the A41...	31
USB:support,	32
USB:support,	32
USB:support,	32
USB Keyboard	32
USB Keyboard	32
The HP Visualize B1000/C3000 workstations support USB keyboards. The keyboard shipped with the wo...	32
The HP Visualize B1000/C3000 workstations support USB keyboards. The keyboard shipped with the wo...	32
The USB keyboard is designed specifically for use with HP workstations. All keyboard models with ...	32
Some applications may expect to use keycodes generated by keys existing on other types of keyboar...	32
NOTE HIL and PS/2 devices are not supported by the B1000/C3000 workstations.	32
NOTE HIL and PS/2 devices are not supported by the B1000/C3000 workstations.	32
USB HP Scroll Mouse	32
USB HP Scroll Mouse	32
The HP scroll mouse (USB) has a left and right button that function the same as most mice. Howeve...	32
The HP scroll mouse (USB) has a left and right button that function the same as most mice. Howeve...	32
For general information on the various cursor shapes associated with different areas of HP CDE wh...	32
HP Hub for USB Devices	32
HP Hub for USB Devices	32
The HP USB hub (part number D6804) provides the ability to connect more than one USB device to th...	32
The HP USB hub (part number D6804) provides the ability to connect more than one USB device to th...	32
Operating System:overview,	33
Operating System:overview,	33
Operating System:overview,	33
This workstation uses the HP-UX operating system, version 10.20 and the Workstation Additional Co...	33

Match case Limit results 1 per page

Chapter 4

125

Field Replaceable Units

FRU Removal and Replacement

cover’s edge is rounded to keep you from cutting the cables. Figure 4-34. Next, place the

end opposite the rear cover handle into the cover slot and tighten the T-15 Torx screw to

secure the rear cover. You have now completed the removal of the CD Drive.

Figure 4-34. Replacing the CD Drive Rear Cover

Installing a Floppy Disk Drive

Install the ﬂoppy disk drive by following the procedure covered in this section. Note there

are no jumper settings required for the installation of the ﬂoppy disk drive.

WARNING

Turn

the

workstation

off

and

unplug

the

power

cord

before

installing the ﬂoppy disk drive.

CAUTION

Floppy disk drives are susceptible to mechanical and electronic shock. When

handling the drive, always wear the static-grounding wrist strap that came in

the Floppy disk drive kit. Always handle the drive carefully.

1. Perform the procedures in the sections “Opening the System Unit Front Panel” and

“Opening the Left Side Panel of the System Unit.” The front panel needs to be opened so

you can insert the ﬂoppy disk drive into its proper location in the chassis. The left side

panel needs to be opened to access the ﬂoppy’s data connector and its power connector.

2. Remove the ﬂoppy rear-disk cover by unscrewing the T-15 Torx screw as shown in

Figure 4-35. Note that the ﬂoppy’s rear cover is located on the rear of the removable

media chassis inside the system unit. Push the cover handle away from the rear of the

removable media chassis approximately one inch. Next pull the cover handle toward

you. The data and power cables are now accessible to you.

Rear Cover Handle

Rear Cover

Audio Cable

ATAPI Cable

Power Cable

T-15

Torx/slotted

Screw