HP Xw8200 Installing an IEEE-1394 card
HP Xw8200 - Workstation - 1 GB RAM Manual
 |
UPC - 882780210455
View all HP Xw8200 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Xw8200 manual content summary:
- HP Xw8200 | Installing an IEEE-1394 card - Page 1
processor kit: ■ IEEE-1394 (a or b) card ■ Y-adapter power cable ■ Warranty ■ Installation instructions Before you begin See http://www.hp.com/accessories/workstations to determine the compatibility of this product with your HP workstation. Observe warnings and cautions Å WARNING: Any surface or - HP Xw8200 | Installing an IEEE-1394 card - Page 2
, including powering down the workstation, disconnecting power from the workstation, opening the access panel, and removing components. For product-specific information, refer to the Service and Technical Reference Guide for your HP workstation at http://www.hp.com/support/workstation_manuals - HP Xw8200 | Installing an IEEE-1394 card - Page 3
Step 2-Remove PCI slot cover Open the PCI retention clamp by pressing down on the clips and moving the clamp toward the rear of the workstation 1. Pull up on the slot cover to remove it from the chassis 2. ✎ NOTE: The following illustrations are shown as examples only. Your system may look - HP Xw8200 | Installing an IEEE-1394 card - Page 4
Installing an IEEE-1394 card Step 3-Install the IEEE-1394 card Ä CAUTION: To prevent damage to this system, observe the following Electro Static Discharge (ESD) precautions while performing the system parts removal/replacement procedures: ❏ Work on a static-free mat. ❏ Wear a static strap to ensure - HP Xw8200 | Installing an IEEE-1394 card - Page 5
Installing an IEEE-1394 card Step 4-Configure cabling HP xw4000/xw6000 series workstations 1. Connect a flexible disk-type power connector from the workstation power supply to the power connector on the IEEE-1394 card 1. Connect the front IEEE-1394 I/O cable to the I/O connector on the IEEE-1394 - HP Xw8200 | Installing an IEEE-1394 card - Page 6
reassemble the workstation using the instructions in the workstation documentation. The reassembly process includes reinstalling the side access panel, restoring power to the workstation, and restarting the workstation. 356318-003 © 2006 Hewlett-Packard Development Company, L.P. The HP Invent logo - HP Xw8200 | Installing an IEEE-1394 card - Page 7
IEEE-1394 IEEE-1394 HP Workstation IEEE-1394 IEEE-1394 (a ま たは b Y HP Workstation http://www.hp.com/accessories/workstations 7/12 - HP Xw8200 | Installing an IEEE-1394 card - Page 8
IEEE-1394 Å Å Safety & Comfort Guide http://www.hp.com/ergo CD HP HP Workstation 手順 1 http://www.hp.com/support/workstation_manuals HP Workstation の 『Service and Technical Reference Guide 8/12 - HP Xw8200 | Installing an IEEE-1394 card - Page 9
IEEE-1394 手順 2 ： PCI PCI 1 2 図 1 PCI 9/12 - HP Xw8200 | Installing an IEEE-1394 card - Page 10
IEEE-1394 手順 3 ： IEEE-1394 Ä ESD IEEE-1394 PCI ま たは PCI Express IEEE-1394 1 参照 )。PCI 2 参照 )。 図 2 IEEE-1394 10/12 - HP Xw8200 | Installing an IEEE-1394 card - Page 11
IEEE-1394 手順 4 HP xw4000/xw6000 1 IEEE-1394 1 IEEE-1394 I/O IEEE-1394 I/O 2 参照 )。 図 3 IEEE-1394 2 1394 す。 1394 11/12 - HP Xw8200 | Installing an IEEE-1394 card - Page 12
-1394 3 参照 )。 図 4 IEEE-1394 Y IEEE-1304b IEEE-1394 IEEE-1394a I/O 1394a I/O 手順 5 IEEE-1394 356318-003 © 2006 Hewlett-Packard Development Company, L.P. HP Invent Hewlett-Packard Development Company, L.P Microsoft と Windows は、 Microsoft Corporation Linux は、 Linus Torvalds 12/12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
1/12
Installing an IEEE-1394 card
Installing an IEEE-1394 card
This document describes how to install an IEEE-1394 card in your HP workstation.
Kit contents
The following components are included in your processor kit:
■
IEEE-1394 (a or b) card
■
Y-adapter power cable
■
Warranty
■
Installation instructions
Before you begin
See
to determine the compatibility of this product with
your HP workstation.
Observe warnings and cautions
Å
WARNING:
Any surface or area of the equipment marked with these symbols indicates the presence of
a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the
risk of injury from a hot component, allow the surface to cool before touching.
Å
WARNING:
Any surface or area of the equipment marked with these symbols indicates the presence of
an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed
area.