HP dx2420 Hardware Reference Guide - dx2420 Microtower Model - Page 39

Installing a 3.5-inch Device Media Card Reader Shown, Installing, Additional Drives,

Get HP dx2420 - Microtower PC PDF manuals and user guides View all HP dx2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

9. Slide the drive in through the front of the chassis (1) until the bezel on the drive is evenly aligned with the computer front bezel and install the two M3 metric retainer screws (2) as shown in the illustration below. NOTE: Extra drive retainer screws are provided on the interior of the front bezel if needed. The M3 metric retainer screws for diskette drives or media card readers are black. Refer to Installing Additional Drives on page 24 for an illustration of the retainer screws location. Figure 2-25 Installing a 3.5-inch Device (Media Card Reader Shown) 10. Connect the appropriate drive cables: a. If installing a diskette drive, connect the power and data cables to the rear of the drive and connect the other end of the data cable to the connector on the system board labeled FDD1. b. If installing a media card reader, connect the USB cable from the media card reader to the USB connector on the system board labeled JUSB2. NOTE: Refer to System Board Drive Connections on page 26 for an illustration of the system board drive connectors. 11. Replace the front bezel and access panel. 12. Reconnect the power cord and turn on the computer. 13. Lock any security devices that were disengaged when the access panel was removed. ENWW Installing Additional Drives 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
9.
Slide the drive in through the front of the chassis (1) until the bezel on the drive is evenly aligned
with the computer front bezel and install the two M3 metric retainer screws (2) as shown in the
illustration below.
NOTE:
Extra drive retainer screws are provided on the interior of the front bezel if needed. The
M3 metric retainer screws for diskette drives or media card readers are black. Refer to
Installing
Additional Drives
on page
24
for an illustration of the retainer screws location.
Figure 2-25
Installing a 3.5-inch Device (Media Card Reader Shown)
10.
Connect the appropriate drive cables:
a.
If installing a diskette drive, connect the power and data cables to the rear of the drive and
connect the other end of the data cable to the connector on the system board labeled FDD1.
b.
If installing a media card reader, connect the USB cable from the media card reader to the
USB connector on the system board labeled JUSB2.
NOTE:
Refer to
System Board Drive Connections
on page
26
for an illustration of the system
board drive connectors.
11.
Replace the front bezel and access panel.
12.
Reconnect the power cord and turn on the computer.
13.
Lock any security devices that were disengaged when the access panel was removed.
ENWW
Installing Additional Drives
33