HP dx2420 Service Reference Guide: HP Compaq dx2420 Business PC - Page 63

Installing the Hard Drive Cage

Get HP dx2420 - Microtower PC PDF manuals and user guides View all HP dx2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

4. Place the hard disk drive cage into the chassis (1), then slide it down toward the bottom of the chassis until it locks into place (2). Figure 6-34 Installing the Hard Drive Cage 5. Attach the two screws that secure the hard disk drive cage to the chassis. Figure 6-35 Securing the Hard Drive Cage 6. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector. NOTE: If your system has only one SATA hard drive, you must connect the hard drive data cable to the dark blue connector labeled SATA1 to avoid any hard drive performance problems. If you are adding a second hard drive, connect the data cable to the next available (unpopulated) SATA connector on the system board in the following order: SATA1, SATA2, SATA4, SATA3. 7. Replace the computer access panel. 8. Lock any security devices that were disengaged when the access panel was removed. Drives 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
4.
Place the hard disk drive cage into the chassis
(1)
, then slide it down toward the bottom of the
chassis until it locks into place
(2)
.
Figure 6-34
Installing the Hard Drive Cage
5.
Attach the two screws that secure the hard disk drive cage to the chassis.
Figure 6-35
Securing the Hard Drive Cage
6.
If installing a new drive, connect the opposite end of the data cable to the appropriate system board
connector.
NOTE:
If your system has only one SATA hard drive, you must connect the hard drive data cable
to the dark blue connector labeled SATA1 to avoid any hard drive performance problems. If you
are adding a second hard drive, connect the data cable to the next available (unpopulated) SATA
connector on the system board in the following order: SATA1, SATA2, SATA4, SATA3.
7.
Replace the computer access panel.
8.
Lock any security devices that were disengaged when the access panel was removed.
Drives
57