Hitachi 42PD5000 Owners Guide - Page 46

INSTALLATION INSTRUCTIONS, Connecting Antenna

Get Hitachi 42PD5000 PDF manuals and user guides View all Hitachi 42PD5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

 23 INSTALLATION INSTRUCTIONS Connecting Antenna Make sure that the power switch of the monitor is turned off. Speaker (R) Monitor rear panel Speaker (L) antenna 20 18 16 14 12 10 8 6 4 2 21 19 17 15 13 11 9 7 5 3 1 When the "ANT" terminal is connected to outdoor antenna instead of CATV system, please note that a good antenna adaptor is necessary. See the diagram on the right. Precautions when connecting the antenna • Clamp section A using pliers when installing the coaxial cable. If other types of adaptors are used, be sure that the core and shielding are good. • Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen. • Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor antenna. • Keep the power cord as far away from the antenna wire as possible. • For safety, install an external antenna conforming to AS1417.1 (applicable for Australia only) If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not provided) for RF LEADS to reduce the noise. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
46
Monitor rear panel
Speaker (R)
Speaker (L)
20
18
16
14
12
10
8
6
4
2
21
19
17
15
13
11
9
7
5
3
1
antenna
When the "ANT" terminal is connected to outdoor antenna instead of CATV system, please note that a good
antenna adaptor is necessary. See the diagram on the right.
Make sure that the power switch of the monitor is turned off.
INSTALLATION INSTRUCTIONS
Connecting Antenna
Precautions when connecting the antenna
• Clamp section
A
using pliers when installing the coaxial cable. If other types of adaptors are used, be sure
that the core and shielding are good.
• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat
feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the
screen.
• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor
antenna.
• Keep the power cord as far away from the antenna wire as possible.
• For safety, install an external antenna conforming to AS1417.1 (applicable for Australia only)
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not
provided) for RF LEADS to reduce the noise.
01 QR58553-英語-初校
03.10.15
10:47 AM
ページ46