Hitachi CPA100 User Manual - Page 41

Description, SOURCE NAME, ENTER, INPUT, RESET

Get Hitachi CPA100 - XGA LCD Projector PDF manuals and user guides
UPC - 050585151314
View all Hitachi CPA100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

SCREEN Menu SCREEN Menu (continued) Item MESSAGE SOURCE NAME Description Using the ▲/▼ buttons turns on/off the message function. TURN ON ó TURN OFF When the TURN ON is selected, the following message function works. "AUTO IN PROGRESS" while automatically adjusting "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "Searching..." while searching for the input "Detecting..." while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the MY MEMORY displayed by changing The indication of "FREEZE" and "II" while the projector is in the FREEZE mode. • If the projector goes into the FREEZE mode while the TURN OFF is selected, the picture on screen is frozen without any messages, which is not a malfunction (23). Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN Menu to select SOURCE NAME and press the ► button. The SOURCE NAME menu will be displayed. (2) Use the ▲/▼ buttons on the SOURCE NAME menu to select the port to be named and press the ► button. Right side of the menu is blank until a name is specified. The SOURCE NAME dialog will be displayed. (3) The current name will be displayed on the first line. Use the buttons and the ENTER or INPUT button to select and enter characters. The RESET button can be used to erase 1 character at a time. Also if you move the cursor to DELETE or ALL CLEAR on screen and push the ENTER or INPUT button, 1 character or all characters will be erased. The name can be a maximum of 16 characters. (4) To change an already inserted character, press the (▲) button to move the cursor to the first line, and use the ◄/► buttons to move the cursor on the character to be changed. After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (3) above. (5) To finish entering text, move the cursor to the SAVE on screen and press the ENTER or INPUT button. To revert to the previous name without saving changes, move the cursor to the CANCEL on screen and press the ENTER or INPUT button. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
4±
SCREEN Menu
SCREEN Menu (continued)
Item
Description
MESSAGE
Using the ▲/▼ buttons turns on/off the message function.
TURN ON
ó
TURN OFF
When the TURN ON is selected, the following message function works.
“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“Searching…” while searching for the input
“Detecting…” while an input signal is detected
The indication of the input signal displayed by changing
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while the projector is in the FREEZE mode.
• If the projector goes into the FREEZE mode while the TURN OFF
is selected, the picture on screen is frozen without any messages,
which is not a malfunction (
23
).
SOURCE NAME
Each input port for this projector can have a name applied to it.
(1)
Use the
▲/▼
buttons on the SCREEN Menu to
select SOURCE NAME and press the
►
button.
The SOURCE NAME menu will be displayed.
(2) Use the ▲/▼ buttons on the SOURCE
NAME menu to select the port to be named
and press the ► button. Right side of the
menu is blank until a name is specified.
The SOURCE NAME dialog will be displayed.
(3)
The current name will be displayed on the
first line. Use the
▲/▼/◄/►
buttons and the
ENTER
or
INPUT
button to select and enter
characters. The
RESET
button can be used
to erase 1 character at a time. Also if you
move the cursor to DELETE or ALL CLEAR on
screen and push the
ENTER
or
INPUT
button,
1 character or all characters will be erased. The
name can be a maximum of 16 characters.
(4)
To change an already inserted character,
press the (
▲
) button to move the cursor to the
first line, and use the
◄/►
buttons to move
the cursor on the character to be changed.
After pressing the
ENTER
or
INPUT
button, the character is selected.
Then, follow the same procedure as described at the item (3) above.
(5) To finish entering text, move the cursor to the SAVE on screen
and press the
ENTER
or
INPUT
button. To revert to the previous
name without saving changes, move the cursor to the CANCEL on
screen and press the
ENTER
or
INPUT
button.