Hitachi CPX505 User Manual - Page 9

Adjusting the projector's elevator, Using the security bar and slot - remote

Get Hitachi CPX505 - XGA LCD Projector PDF manuals and user guides
UPC - 050585151093
View all Hitachi CPX505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

RGB OUT Y VIDEO RGB1 CB/PB RGB2 M1-D Setting up Adjusting the projectCoR/rPR's elevator When the place to put the projector is slightlRyEMuOnTEeven to the left or right, use the eUSl-seViIvDnEagOtothr eRfeAfUeeDteIOttoINc3paLlnacaRelAsUtoDhIOetiIlNtp4trLhoejepctrooArjeOUhUDcTIoOtorirzoinnotarCdlO(l3yNe.5.TΦrR)OtLo project at CONTROL a suitable angle to the screen, projector within 8 degrees. elevating the front side oAfCthINe q This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is adjustable while pulling up the elevatIor kOnob on the same side as it. 1. Holding the projector, pull the elevator knobs up to loose the elevator feet. 2. Position the front side of the projector to the desired height. 3. Release the elevator knobs in order to lock the elevator feet. 4. After making sure that the elevator feet are locked, put the projector gently. 5. If necessary, the elevator feet can be manually twisted to make more precise adjustments. Hold the projector when twisting the feet. To loose an elevator foot, pull up the elevator knob on the same side as it. To finely adjust, twist the foot. CAUTION ►Do not handle the elevator knobs without holding the projector, since the projector may drop down. ►Do not tilt the projector other than it elevating its front within 8 degrees using the adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables, or the projector itself. Using the security bar and slot A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool. WARNING ►Do not use the securLitAyN bar and the security slot to prevent the projector from falling down, since it is not designed for it. NOTREOGUBT• The securityRGbBa1r and the secRuGrBit2y slot are not M1-D comprehensiYve theft preveCnB/PtiBon measures. They are intended toVbIDeEOused as supplemental theft prevention measure. CR/PR Security bar Anti-theft chain or wire Security slot 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
9
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the
elevator feet to place the projector horizontally.
Using the feet can also tilt the projector in order to project at
a suitable angle to the screen, elevating the front side of the
projector within 8 degrees.
This projector has ² elevator feet and ² elevator knobs. An elevator foot is
adjustable while pulling up the elevator knob on the same side as it.
±.
Holding the projector, pull the elevator knobs up to loose the elevator feet.
².
Position the front side of the projector to the desired height.
3.
Release the elevator knobs in order to lock the elevator feet.
4.
After making sure that the elevator feet are locked, put the projector gently.
5.
If necessary, the elevator feet can be manually twisted to make more precise
adjustments. Hold the projector when twisting the feet.
Setting up
To loose an elevator foot,
pull up the elevator knob
on the same side as it.
CAUTION
►Do not handle the elevator knobs without holding the projector,
since the projector may drop down.
►Do not tilt the projector other than it elevating its front within 8 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
Using the security bar and slot
A commercial anti-theft chain or wire up to ±0 mm in
diameter can be attached to the security bar on the
projector.
Also this product has the security slot for the Kensington
lock.
For details, see the manual of the security tool.
WARNING
►Do not use the security bar and the
security slot to prevent the projector from falling down,
since it is not designed for it.
NOTE
•
The security bar and the security slot are not
comprehensive theft prevention measures. They are intended
to be used as supplemental theft prevention measure.
To finely adjust, twist
the foot.
Security slot
Anti-theft chain or wire
Security bar