Home » Hitachi Manuals » Hard Drives » Hitachi IC25N080ATMR04-0 » Manual Viewer

Hitachi IC25N080ATMR04-0 Specifications - Page 195

Write Multiple C5h

UPC - 000000114196

View all Hitachi IC25N080ATMR04-0 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 195 highlights

13.45 Write Multiple (C5h) Table 128: Write Multiple (C5h) Command Block Output Registers Register 7 6 5 4 3 2 1 0 Data Feature Sector Count V V V V V V V V LBA Low V V V V V V V V LBA Mid V V V V V V V V LBA High V V V V V V V V Device 1 L 1 D H H H H Command 1 1 0 0 0 1 0 1 76 CRC UNC 00 Error Register 54 3 2 1 0 0 IDN 0 ABT T0N AMN 0V 0 V 0 0 Command Block Input Registers Register 7 6 5 4 3 2 1 0 Data Error see below Sector Count V V V V V V V V LBA Low V V V V V V V V LBA Mid V V V V V V V V LBA High V V V V V V V V Device - - - - H H H H Status see below Status Register 7 654 3 2 1 0 BSY RDY DF DSC DRQ COR IDX ERR 0 VVV - 0 - V The Write Multiple command transfers one or more sectors from the host to the device. The data is then written to the disk media. Command execution is identical to the Write Sectors command except that an interrupt is generated for each block as defined by the Set Multiple command instead of for each sector. The sectors are transferred through the Data Register 16 bits at a time. Output parameters to the device Sector Count LBA Low LBA High/MId H This indicates the number of continuous sectors to be transferred. If the Sector Count of zero is specified, 256 sectors will be transferred. This indicates the sector number of the first sector to be transferred. (L = 0) In LBA mode this register contains the LBA bits 0-7. (L = 1) This indicates the cylinder number of the first sector to be transferred. (L = 0) In LBA mode this register contains the LBA bits 8-15 (Mid) and bits 16-23(High).(L = 1) This indicates the head number of the first sector to be transferred. (L = 0) In LBA mode this register contains the LBA bits 24-27. (L = 1) Input parameters from the device Sector Count LBA Low LBA High/Mid H This indicates the number of requested sectors not transferred. The Sector Count will be zero, unless an unrecoverable error occurs. This indicates the sector number of the last transferred sector. (L = 0) In LBA mode this register contains current the LBA bits 0-7. (L = 1) This indicates the cylinder number of the last transferred sector. (L = 0) In LBA mode this register contains the current LBA bits 8-15 (Mid) and bits 16-23 (High). (L = 1) This indicates the head number of the last transferred sector. (L = 0) In LBA mode this register contains current the LBA bits 24-27. (L = 1) Travelstar 80GN Hard Disk Drive Specification 185

Section	Page
1.0 General	15
1.1 Introduction	15
1.2 References	15
1.3 Abbreviations	15
1.4 Caution	17
1.5 Drive handling precautions	18
2.0 Outline of the drive	19
3.0 Fixed-disk subsystem description	23
3.1 Control electronics	23
3.2 Head disk assembly data	23
4.0 Drive characteristics	25
4.1 Formatted capacity	25
4.2 Data sheet	25
4.3 Cylinder allocation	26
4.4 Performance characteristics	27
4.4.1 Command overhead	27
4.4.2 Mechanical positioning	27
4.4.3 Operating modes	29
5.0 Data integrity	31
5.1 Data loss at power off	31
5.2 Write Cache	31
5.3 Equipment status	31
5.4 WRITE safety	32
5.5 Data buffer test	32
5.6 Error recovery	32
5.7 Automatic reallocation	32
5.8 ECC	33
6.0 Specification	35
6.1 Environment	35
6.1.1 Temperature and humidity	35
6.1.2 Radiation noise	36
6.1.3 Conductive noise	37
6.1.4 Magnetic fields	37
6.2 DC power requirements	37
6.2.1 Power consumption efficiency	38
6.3 Reliability	38
6.3.1 Data Reliability	38
6.3.2 Failure prediction (S.M.A.R.T.)	38
6.3.3 Cable noise interference	38
6.3.4 Service life and usage condition	39
6.3.5 Preventive maintenance	39
6.3.6 Load/unload	39
6.4 Mechanical specifications	41
6.4.1 Physical dimensions and weight	41
6.4.2 Mounting hole locations	42
6.4.3 Connector and jumper description	42
6.4.4 Mounting orientation	43
6.4.5 Load/unload mechanism	43
6.5 Vibration and shock	43
6.5.1 Operating vibration	43
6.5.2 Nonoperating vibration	44
6.5.3 Operating shock	44
6.5.4 Nonoperating shock	45
6.6 Acoustics	45
6.6.1 Sound power levels	45
6.6.2 Discrete tone penalty	46
6.7 Identification labels	46
6.8 Electromagnetic compatibility	46
6.8.1 CE mark	46
6.8.2 C-TICK mark	46
6.8.3 BSMI mark	46
6.8.4 MIC mark	47
6.9 Safety	47
6.9.1 UL and CSA approval	47
6.9.2 IEC compliance	47
6.9.3 German safety mark	47
6.9.4 Flammability	47
6.9.5 Secondary circuit protection	47
6.10 Packaging	47
7.0 Electrical interface specification	49
7.1 Cabling	49
7.2 Interface connector	49
7.3 Signal definitions	50
7.4 Signal descriptions	51
7.5 Interface logic signal levels	54
7.6 Reset timings	54
7.7 PIO timings	55
7.8 Multi word DMA timings	56
7.9 Ultra DMA timings	57
7.9.1 Initiating Read DMA	57
7.9.2 Host Pausing Read DMA	58
7.9.3 Host Terminating Read DMA	59
7.9.4 Device Terminating Read DMA	60
7.9.5 Initiating Write DMA	61
7.9.6 Device Pausing Write DMA	62
7.9.7 Device Terminating Write DMA	63
7.9.8 Host Terminating Write DMA	64
7.10 Drive address setting	65
7.11 Addressing of HDD registers	66
8.0 General	69
8.1 Introduction	69
8.2 Terminology	69
9.0 Deviations from standard	71
10.0 Register	73
10.1 Alternate Status Register	74
10.2 Command Register	74
10.3 Data Register	74
10.4 Device Control Register	75
10.5 Drive Address Register	75
10.6 Device/Head Register	76
10.7 Error Register	76
10.8 Features Register	77
10.9 LBA High Register	77
10.10 LBA Mid Register	77
10.11 Sector Count Register	77
10.12 Status Register	77
11.0 General	79
11.1 Reset response	79
11.2 Register initialization	80
11.3 Diagnostic and Reset considerations	81
11.4 Power-off considerations	82
11.4.1 Load/Unload	82
11.4.2 Emergency unload	82
11.4.3 Required power-off sequence	82
11.5 Sector Addressing Mode	83
11.5.1 Logical CHS addressing mode	83
11.5.2 LBA addressing mode	83
11.6 Power management features	84
11.6.1 Power mode	84
11.6.2 Power management commands	84
11.6.3 Standby/Sleep command completion time	84
11.6.4 Standby timer	85
11.6.5 Status	85
11.6.6 Interface capability for power modes	85
11.6.7 Initial Power Mode at Power On	85
11.7 Advanced Power Management (ABLE-3) feature	85
11.7.1 Performance Idle Mode	86
11.7.2 Active Idle Mode	86
11.7.3 Low Power Idle Mode	86
11.7.4 Transition time	86
11.8 S.M.A.R.T. Function	87
11.8.1 Attributes	87
11.8.2 Attribute values	87
11.8.3 Attribute thresholds	87
11.8.4 Threshold exceeded condition	87
11.8.5 S.M.A.R.T. commands	87
11.8.6 S.M.A.R.T. operation with power management modes	88
11.9 Security Mode Feature Set	88
11.9.1 Security mode	88
11.9.2 Security level	88
11.9.3 Password	89
11.9.4 Master Password Revision Code	89
11.9.5 Command table	92
11.10 Protected Area Function	93
11.10.1 Example for operation (In LBA Mode)	93
11.10.2 Set Max security extension commands	94
11.11 Address Offset Feature (vendor specific)	95
11.11.1 Enable/Disable Address Offset Mode	95
11.11.2 Identify Device Data	96
11.11.3 Exceptions in Address Offset Mode	96
11.12 Seek Overlap	97
11.13 Write Cache function	97
11.14 Reassign Function	98
11.14.1 Auto Reassign Function	98
11.15 48-bit Address Feature Set	99
12.0 Command protocol	101
12.1 Data In commands	101
12.2 Data Out Commands	102
12.3 Non-data commands	103
12.4 DMA Data Transfer commands:	105
13.0 Command descriptions	107
13.1 Check Power Mode (E5h/98h)	111
13.2 Device Configuration Overlay (B1h)	112
13.2.1 DEVICE CONFIGURATION RESTORE (subcommand C0h)	112
13.2.2 DEVICE CONFIGURATION FREEZE LOCK (subcommand C1h)	112
13.2.3 DEVICE CONFIGURATION IDENTIFY (subcommand C2h)	113
13.2.4 DEVICE CONFIGURATION SET (subcommand C3h)	113
13.3 Execute Device Diagnostic (90h)	115
13.4 Flush Cache (E7h)	116
13.5 Flush Cache EXT (EAh)	117
13.6 Format Track (50h: vendor specific)	118
13.7 Format Unit (F7h: vendor specific)	119
13.8 Identify Device (ECh)	120
13.9 Idle (E3h/97h)	129
13.10 Idle Immediate (E1h/95h)	130
13.11 Initialize Device Parameters (91h)	132
13.12 Read Buffer (E4h)	133
13.13 Read DMA (C8h/C9h)	134
13.14 Read DMA EXT (25h)	136
13.15 Read Long (22h/23h)	138
13.16 Read Multiple (C4h)	140
13.17 Read Multiple EXT (29h)	142
13.18 Read Native Max ADDRESS (F8h)	143
13.19 Read Native Max ADDRESS EXT (27h)	144
13.20 Read Sectors (20h/21h)	145
13.21 Read Sector(s) EXT (24h)	146
13.22 Read Verify Sectors (40h/41h)	148
13.23 Ready Verify Sector(s) EXT (42h)	150
13.24 Recalibrate (1xh)	152
13.25 Security Disable Password (F6h)	153
13.26 Security Disable Password (F6h)	154
13.27 Security Erase Unit (F4h)	155
13.28 Security Freeze Lock (F5h)	157
13.29 Security Set Password (F1h)	158
13.30 Security Unlock (F2h)	160
13.31 Seek (7xh)	161
13.32 Sense Condition (F0h: vendor specific)	162
13.33 Set Features (EFh)	163
13.34 Set Max ADDRESS (F9h)	165
13.35 Set Max ADDRESS EXT (37h)	167
13.36 Set Multiple (C9h)	169
13.37 Sleep (E6h/99h)	170
13.38 S.M.A.R.T. Function Set (B0h)	171
13.38.1 S.M.A.R.T. Function Subcommands	172
13.38.2 Device Attribute Data Structure	176
13.38.3 Device Attribute Thresholds data structure	181
13.38.4 S.M.A.R.T. error log sector	182
13.38.5 Self-test log data structure	184
13.38.6 Error reporting	185
13.39 Standby (E2h/96h)	186
13.40 Standby Immediate (E0h/94h)	187
13.41 Write Buffer (E8h)	188
13.42 Write DMA (CAh/CBh)	189
13.43 Write DMA EXT (35h)	191
13.44 Write Long (32h/33h)	193
13.45 Write Multiple (C5h)	195
13.46 Write Multiple EXT (39h)	196
13.47 Write Sectors (30h/31h)	198
13.48 Write Sectors(s) EXT (34h)	200
13.49 Write Verify (3Ch: vendor specific)	201
14.0 Time-out values	203
15.0 Appendix	205
15.1 Commands Support Coverage	205
15.2 SET FEATURES Commands Support Coverage	207
15.3 Changes from Travelstar 60GH and 40GN	208
A	211
B	211
C	211
D	211
E	211
F	211
H	211
I	211
L	211
M	211
N	212
O	212
P	212
R	212
S	212
T	212
U	212
V	213
W	213

Match case Limit results 1 per page

Travelstar 80GN Hard Disk Drive Specification

185

13.45

Write Multiple (C5h)

Table 128: Write Multiple (C5h)

The Write Multiple command transfers one or more sectors from the host to the device. The data is then written to

the disk media.

Command execution is identical to the Write Sectors command except that an interrupt is generated for each block

as defined by the Set Multiple command instead of for each sector. The sectors are transferred through the Data

Output parameters to the device

Sector Count

This indicates the number of continuous sectors to be transferred. If the Sector Count of

zero is specified, 256 sectors will be transferred.

LBA Low

This indicates the sector number of the first sector to be transferred. (L = 0)

In LBA mode this register contains the LBA bits 0–7. (L = 1)

LBA High/MId

This indicates the cylinder number of the first sector to be transferred. (L = 0)

In LBA mode this register contains the LBA bits 8–15 (Mid) and bits 16–23(High).(L = 1)

This indicates the head number of the first sector to be transferred. (L = 0)

In LBA mode this register contains the LBA bits 24–27. (L = 1)

Input parameters from the device

Sector Count

This indicates the number of requested sectors not transferred. The Sector Count will be

zero, unless an unrecoverable error occurs.

LBA Low

This indicates the sector number of the last transferred sector. (L = 0)

In LBA mode this register contains current the LBA bits 0–7. (L = 1)

LBA High/Mid

This indicates the cylinder number of the last transferred sector. (L = 0)

In LBA mode this register contains the current LBA bits 8–15 (Mid) and bits 16–23

(High). (L = 1)

This indicates the head number of the last transferred sector. (L = 0)

In LBA mode this register contains current the LBA bits 24–27. (L = 1)

Command Block Output Registers

Command Block Input Registers

7 6 5 4 3 2 1 0

Data

- - - - - - - -

Data

- - - - - - - -

Feature

- - - - - - - -

Error

see below

Sector Count

V V V V V V V V

Sector Count

V V V V V V V V

LBA Low

V V V V V V V V

LBA Low

V V V V V V V V

LBA Mid

V V V V V V V V

LBA Mid

V V V V V V V V

LBA High

V V V V V V V V

LBA High

V V V V V V V V

Device

1 L 1 D H H H H

Device

- - - - H H H H

Command

1 1 0 0 0 1 0 1

Status

see below

Error Register

Status Register

CRC UNC 0 IDN 0 ABT T0N AMN

BSY RDY DF DSC DRQ COR IDX ERR