Holmes HM2610 Product Manual - Page 2

Lea Y Conserve Estas Importantes

Page 2 highlights

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using the appliance. 2. To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet. 3. Keep the cord out of heavy traffic areas. To avoid fire hazard, NEVER put the cord under rugs or near heat registers. 4. DO NOT place humidifier near heat sources such as stoves, radiators, and heaters. DO locate your humidifier on an inside wall near an electrical outlet. The humidifier should be at least 4 inches (10 cm) away from the wall for best results. 5. NEVER place humidifier in an area where it is accessible to children. NEVER use humidifier in a closed room, particularly where a child may be sleeping, resting, or playing (a closed room may result in excessive humidity). 6. WARNING: Do not attempt to refill humidifier without first unplugging the unit from its electrical outlet. Failure to heed this warning may cause personal injury. Be sure to unplug the unit by pulling on the plug and not the cord. 7. Never place anything over moisture outlet when the unit is running. 8. NEVER drop or insert any object into any openings. 9. DO NOT operate any appliance with a damaged cord or plug, after the appliance malfunctions, or if it has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair. 10. Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by the manufacturer may cause hazards. 11. DO NOT use outdoors. 12. Always place humidifier on a firm, flat, level surface. A waterproof mat or pad is recommended for use under the humidifier. NEVER place it on a rug or carpet, or on a finished floor that may be damaged by exposure to water or moisture. 13. DO NOT allow the Moisture Outlet to directly face the wall. Moisture could cause damage, particularly to wall paper. 14. Humidifier should be unplugged when not in use. 15. NEVER tilt, move, or attempt to empty unit while it is operating. Shut off and unplug before removing the water tank and moving the unit. 16. This humidifier requires daily and weekly maintenance to operate appropriately. Refer to daily and weekly cleaning procedures. Use only cleaners and additives recommended by the manufacturer. 17. NEVER use detergents, gasoline, glass cleaner, furniture polish, paint thinner, or other household solvents to clean any part of the humidifier. 18. Excessive humidity in a room can cause water condensation on windows and some furniture. If this happens, turn the humidifier OFF. 19. Do not use humidifier in an area where humidity level is in excess of 50%. Use a hygrometer, available at your local retailer or through the manufacturer, to measure the humidity. 20. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 21. Never place housing under water flow or immerse in liquids. THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY. FEATURES - OPERATIONS 22. Do not plug in the cord with wet hands: electric shock could result. 23. Do not pour water in any openings other than the water tank. 24. To prevent damage to surfaces, do not place humidifier under overhanging surfaces. 25. NEVER operate unit without water in the tank. 26. Do not move unit after it has been used until unit cools completely. 27. Use both hands when carrying full tank of water. PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS HOW ULTRASONIC WORKS: An ultrasonic transducer atomizes water, producing refreshing visible cool mist. NOTE: A humidity level below 20% can be unhealthy and uncomfortable. The recommended humidity level is between 40%-50%. PRE-OPERATING INSTRUCTIONS 1. Be sure the humidifier is switched OFF and the unit is disconnected from the electrical outlet. 2. Select a location for your humidifier, on a flat surface, about 4 inches (10 cm) away from the wall. DO NOT place the humidifier on a finished floor or near furniture, which can be damaged by too much moisture or water. Place on a moisture resistant surface. CONSUMER SAFETY INFORMATION NOTE: This is an electrical appliance and requires attention when in use. NOTE: If moisture forms on the walls or windows of the room, turn off the humidifier. The room already has plenty of humidity and additional moisture may cause damage. NOTE: DO NOT block air inlet or outlet. Cord and Plug Installation Safety Instructions: The length of cord used on this appliance was selected to reduce the hazards of becoming tangled in, or tripping over a longer cord. If a longer cord is necessary an approved extension cord may be used. The electrical rating of the extension cord must be equal to or greater than the rating of the humidifier (refer to the rating information placed on the humidifier). Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or accidentally tripped over. FILLING THE WATER TANK Tank Cap Tablet Holder The tank cap of the humidifier features a cage that holds humidifier enhancement tablets. It is located on the tank cap to ensure all water is treated by the tablet before it passes through to the base of the humidifier. Pop off the top of the green cage and place tablet directly inside. Close the top of the green cage and replace the tank cap on tank FIRMLY (see Figure 1). NOTE: Only one humidifier enhancement tablet should be used per tank filling. To order more humidifier enhancement tablets, go to www.holmesproducts.com or call customer service at 1-800-546-5637. 1. Remove the tank from the main housing. 2. Bring the tank to the sink, turn upside down and twist off the tank cap by turning counterclockwise. Fill tank with cool, fresh tap water. DO NOT fill with warm water as this may cause leaking. Replace the cap on tank FIRMLY. 3. Place tank back on to the base. The tank will immediately begin to empty into the base. 4. Plug the humidifier into a 120V electrical outlet. FEATURES - OPERATIONS Figure 1 Place tablet inside Pop off the cage top Tank Cap Figure 2 B A C F D E A. Carry Handle B. Water Tank C. Humidifier Housing D. Humidifier Base E. Control Knob F. Tank Cap with the Cage OPERATING INSTRUCTIONS 1. To turn the humidifier on, turn the Control Knob clockwise to produce the highest moisture level ( ). Continuing to turn the knob clockwise will produce lower moisture level ( ) but with longer run time and quieter performance. 2. To turn off the unit, switch the Control Knob to the Off position. 3. Once the tank is empty, turn off your humidifier and unplug it from the electrical outlet. Before refilling, empty any residual water from the base and the tank (follow the daily maintenance instructions). Then follow the above Filling Instructions to refill the tank. WARNING: DO NOT move the humidifier with water in the tank or the humidifier base. The moving action of the water may activate the water tank's release nozzle and overfill the humidifier base. This may cause the humidifier to function intermittently, or stop emitting mist. Should this occurs, simply remove the excess water from the humidifier base. NOTES: • High setting will produce the maximum moisture level and Low setting will produce the longest run time and quieter performance. CLEANING / MAINTENANCE CLEANING AND MAINTENANCE INSTRUCTIONS Humidifiers provide comfort by adding moisture to dry, heated indoor air. To benefit most from the humidifier and avoid product misuse, follow all instructions carefully. Please note that this is an electrical appliance and requires attention when in use. In addition, if you do not follow the recommended care and maintenance guidelines, micro-organisms may be able to grow in the water within the water tank. You must routinely follow the cleaning procedures that follow in order to ensure proper, efficient operation of your humidifier. Proper maintenance and cleaning is essential to the continued performance of your unit and the avoidance of algae or bacteria build-up. Daily Maintenance: 1. Be sure the unit is OFF and is disconnected from the electrical outlet. 2. Carry the base of the unit to the sink, place in sink, drain any remaining water and rinse thoroughly to remove any sediment or dirt. Wipe clean, and dry with a clean cloth or paper towel. 3. Drain the water from the tank into the sink and rinse tank thoroughly. Wipe clean, and dry with a clean cloth or paper towel. 4. Replace the housing, then refill tank with cool tap water as instructed earlier in the Filling Instructions. Do not overfill. 5. Follow Operating Instructions to turn on the humidifier. Weekly Maintenance: To Remove Scale: 1. Repeat previous steps in Daily Maintenance. 2. Clean the base by partially filling the base with one 8-oz cups of undiluted white vinegar, or by using Cleanse Clean® Solution (Model S1710) by the manufacturer. Leave this solution in the base for 20 minutes, while cleaning all the interior surfaces with a soft brush (brush not included). Gently scrub the area around the transducer (located at the humidifier base) with a soft brush. Remove base scale by wiping the base with a cloth dampened with undiluted white vinegar. (see Figure 3) 3. Rinse with clean warm water to remove the cleaning solution before disinfecting the tank. To Disinfect Humidifier Base and Tank: 1. Fill humidifier tank 1/2 full with water and 1/2 tablespoon of chlorine bleach. 2. Let the solution stand for 20 minutes, swishing every few minutes. Wet all surfaces. 3. Carefully empty the tank after 20 minutes, and rinse with warm water until you cannot detect any bleach smell. Dry with a clean cloth or paper towel. 4. Refill the water tank with cool water and replace on housing (see Filling Instructions above). Follow Operating Instructions to turn the humidifier ON. 5. To clean the humidifier base, pour out all access water. Rise thoroughly to remove any sediment to dirt. Wipe clean and dry with a clean cloth or paper towel. Do not use metal cleaning utensils of abrasive cleansers. Figure 3 Transducer Humidifier Base STORAGE INSTRUCTIONS REPLACEMENT ACCESSORIES STORAGE INSTRUCTIONS When not using your humidifier for an extended period of time: 1. Clean, rinse and thoroughly dry the humidifier as directed in weekly maintenance. DO NOT leave any water in the unit when storing. Leaving water in the unit may render the unit inoperable for the following season. 2. Place the humidifier in the original carton and store in a cool, dry place. REPLACEMENT ACCESSORIES To order the replacement accessories you can do any of the following: • Visit your local retailer • Go to www.holmesproducts.com • Call Consumer Service at 1-800-546-5637 LEA Y CONSERVE ESTAS IMPORTANTES INSTRUCCIONES DE SEGURIDAD Debe tomar precauciones básicas de seguridad siempre que utilice artefactos eléctricos para reducir el riesgo de incendio, descarga eléctrica y daños personales, incluyendo lo siguiente: 1. Lea completamente las instrucciones antes de utilizar el artefacto. 2. Para evitar incendio o descarga eléctrica, enchufe el artefacto directamente en un tomacorriente de 120V CA. 3. Mantenga el cable fuera de las zonas de mucho tráfico. Para evitar incendios, NUNCA coloque el cable debajo de alfombrillas o cerca de salidas de calefacción. 4. NO coloque el humidificador cerca de fuentes de calor como estufas, radiadores y calefactores. NO coloque el humidificador contra una pared interna cerca de un tomacorriente. El humidificador debe estar a por lo menos 4" de la pared para obtener el mejor resultado. 5. NUNCA coloque el humidificador en una zona accesible para los niños. NUNCA use el humidificador en un cuarto cerrado, especialmente donde pueda haber un niño durmiendo, descansando, o jugando (un cuarto cerrado puede resultar en excesiva humedad). 6. ADVERTENCIA: No intente llenar nuevamente el humidificador sin antes desenchufarlo del tomacorriente. El no tener en cuenta esta advertencia puede causar daños personales. Asegúrese de desenchufar la unidad tirando del enchufe y no del cable. 7. Nunca coloque algo sobre la salida de humedad cuando la unidad esté funcionando. 8. NUNCA inserte ningún objeto en una de las ranuras. 9. NO utilice ningún artefacto si el cable o el enchufe están dañados, luego de una falla, o si se ha caído o ha sufrido cualquier tipo de daño. Devuelva el artefacto al fabricante para su inspección, ajuste eléctrico o mecánico, o reparación. 10. Utilice el artefacto únicamente para el propósito hogareño indicado en este manual. Cualquier uso distinto al recomendado por el fabricante puede causar incendio, descarga eléctrica, o daños personales. El uso de accesorios no recomendados o que no sean vendidos por el fabricante puede ser peligroso. 11. NO utilizar en el exterior. 12. Siempre coloque el humidificador en una superficie firme, plana y nivelada. Se recomienda el colocar una alfombrilla o bandeja resistente al agua debajo del humidificador. NUNCA lo coloque sobre un tapete o una alfombra, o en un piso que pueda dañarse con el agua o la humedad. 13. NO haga que la salida de humedad apunte directamente a la pared. La humedad puede causar daños, especialmente al empapelado. 14. Se debe desenchufar el humidificador cuando no se usa. 15. NUNCA incline, mueva o intente vaciar la unidad mientras esté funcionando. Apague y desenchufe la unidad antes de quitar el tanque de agua y moverla. 16. Este humidificador requiere mantenimiento diario y semanal para funcionar correctamente. Refiérase a los procedimientos de limpieza diarios y semanales. Use únicamente limpiadores y aditivos recomendados por el fabricante. 17. NUNCA use detergentes, gasolina, limpiavidrios, limpiador de muebles, diluyente de pintura u otro solvente hogareño para limpiar ninguna parte del humidificador. 18. La humedad excesiva en un cuarto puede causar condensación de agua en las ventanas y en algunos muebles. Si sucede esto, apague el humidificador. 19. No use el humidificador en un área donde el nivel de humedad es mayor al 50%. Use un Higrómetro, disponible en su tienda local o a través del fabricante, para medir la humedad. 20. NO intente reparar o ajustar ninguna función eléctrica o mecánica de esta unidad. El hacerlo invalidará la garantía. La unidad no contiene partes reparables por el usuario. Toda reparación debe ser ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica, este enchufe está diseñado para insertarse en un tomacorriente polarizado en un solo sentido. Si el enchufe no entra completamente en el tomacorriente, inviértalo. Si aun así no entra, llame a un electricista calificado para instalar un tomacorriente apropiado. NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD DE NINGUNA MANERA. CARACTERISTICA - FUNCIONAMIENTO realizada únicamente por personal calificado. 21. Nunca coloque el gabinete debajo de la canilla o lo sumerja en líquidos. 22. No enchufe el cable con las manos húmedas. Puede ocasionarle una descarga eléctrica. 23. No coloque agua en ninguna abertura que no sea el tanque de agua. 24. Para prevenir el daño a las superficies, no coloque el humidificador debajo de ninguna superficie que sobresalga por encima del mismo. 25. NUNCA haga funcionar la unidad sin agua en el tanque. 26. Una vez utilizada la unidad, no la mueva hasta que se haya enfriado completamente. 27. Use las dos manos cuando cargue el tanque de agua. LEA Y CONSERVE ESTAS IMPORTANTES INSTRUCCIONES DE SEGURIDAD INFORMACIÓN DE SEGURIDAD PARA EL CONSUMIDOR NOTA: Este es un artefacto eléctrico y requiere ser usado con cuidado. NOTA: Si se acumula humedad en las paredes o ventanas del cuarto, apague el humidificador. El cuarto ya tiene demasiada humedad y la humedad adicional puede causar daños. NOTA: NO bloquee la entrada o salida de aire. Instrucciones de Seguridad en la Instalación del Cable y el Enchufe : La longitud del cable de este artefacto fue seleccionada para reducir el riesgo de enredarse o tropezarse con un cable más largo. Si necesita usar un cable más largo, puede utilizar un cable de extensión aprobado. La capacidad eléctrica del cable de extensión debe ser igual o mayor que la capacidad del humidificador (consulte la información sobre clasificación que se encuentra en el humidificador). No debe permitir que el cable de extensión cuelgue de la mesada o mesa de tal forma que pueda ser jalado por niños o causar que alguien se tropiece. CÓMO FUNCIONA ULTRASONIC: Un transductor ultrasónico atomiza el agua y produce un refrescante vapor frío y visible. NOTA: Un nivel de humedad menor al 20% puede ser nocivo e incómodo. El nivel de humedad recomendado es entre el 40% y el 50%. INSTRUCCIONES PREVIAS AL USO 1. Asegúrese de que el humidificador esté en OFF (Apagado) y desenchúfelo del tomacorriente. 2. Elija un lugar para su humidificador, en una superficie plana, aproximadamente a 4 pulgadas de distancia de la pared. NO coloque el humidificador sobre un piso pulido o cerca de algún mueble, ya que lo puede dañar por el exceso de humedad o agua. Colóquelo sobre una superficie resistente a la humedad. COMO LLENAR EL TANQUE DE AGUA Compartimiento del tapón del tanque para tabletas El tapón del tanque del humidificador cuenta con un compartimiento en el que se pueden colocar tabletas intensificadoras del humidificador. Se encuentra ubicado en el tapón del tanque a fin de garantizar que toda el agua sea tratada con la tableta antes de pasar a través de la base del humidificador. Levante la parte superior del compartimiento verde y coloque la tableta directamente en el interior. Cierre la parte superior del compartimiento y reemplace el tapón del tanque en el tanque CON FIRMEZA (vea la Figura 1). NOTA: Se debe usar solo una tableta intensificadora del humidificador por llenado del tanque. Para solicitar más tabletas intensificadoras del humidificador, visite www.holmesproducts.com o llame al servicio de atención al cliente al 1-800-546-5637. 1. Retire el tanque de la caja principal. 2. Acerque el tanque hasta la pileta, délo vuelta y desenrosque la tapa del tanque girando en sentido contrario a las agujas del reloj. Llene el tanque con agua fría del grifo. NO llene con agua caliente ya que esto puede producir una pérdida. Vuelva a colocar la tapa del tanque CON FIRMEZA. CARACTERISTICA - FUNCIONAMIENTO 3. Coloque el tanque nuevamente sobre la base. El tanque comenzará a vaciarse inmediatamente en la base. 4. Enchufe el cable de corriente en un tomacorriente de 120 voltios AC. INSTRUCCIONES DE USO 1. Para encender el humidificador, gire la perilla de control en el sentido de las agujas del reloj para generar el nivel más alto de humedad ( ). Continuar girando la perilla en dirección de las manecillas del reloj producirá un nivel menor de humedad ( ) pero por un tiempo más largo y con un rendimiento más silencioso. 2. Para apagar la unidad, gire la perilla de control hasta alcanzar la posición Apagado. Figura 1 Coloque la tableta en el interior Quite la parte superior del compartimiento Tapón del tanque Figura 2 B A C 3. Una vez que el tanque se encuentre vacío, apague el humidificador y desconéctelo del tomacorrientes. Antes de llenarlo nuevamente, vacíe el tanque y la base de todo resto de agua (siga las instrucciones de mantenimiento diario). Luego, siga las instrucciones de llenado que aparecen previamente para llenar nuevamente el tanque. ADVERTENCIA: NO MUEVA el humidificador cuando tenga agua en el tanque o en la base. La acción de movimiento podría activar la boquilla de descarga del tanque de agua y saturar la base del humidificador. Si sucediera, el humidificador funcionaría intermitentemente y dejaría de emitir vapor. En este caso, simplemente elimine el exceso de agua de la base del humidificador. NOTAS: • La posición alta producirá el máximo nivel de humedad y una posición baja ofrecerá el mayor tiempo de uso y un funcionamiento más silencioso. INSTRUCCIONES DE LIMPIEZA Y MANTENIMIENTO Los humidificadores proveen confort agregando humedad al aire seco de los ambientes interiores calefaccionados. Para beneficiarse al máximo de los humidificadores y evitar su mal uso, siga todas las instrucciones cuidadosamente. Tenga en cuenta que éste es un artefacto eléctrico que requiere atención cuando esté en uso. Además, si no se siguen las recomendaciones para el cuidado y mantenimiento, crecerán microorganismos en el agua dentro de los tanques. Se deben ejecutar rutinariamente los procedimientos de limpieza que se indican a continuación para asegurar el funcionamiento adecuado y eficiente del humidificador que son esenciales para el rendimiento óptimo constante de la unidad y para evitar la formación de algas y bacterias. F E A. Manija de traslado B. Tanque de agua C. Cubierta del humidificador D D. Base del humidificador E. Perilla de control F. Tapón del tanque con el compartimiento LIMPIEZA Y MANTENIMIENTO Mantenimiento diario : 1. Asegúrese de apagar y desenchufar la unidad del tomacorriente. 2. Lleve la base de la unidad al fregadero o a la tina, coloque la base en el fregadero, drene el agua remanente, enjeague completamente para remover cualquier sedimento o suciedad, limpie frotando con un paño y seque con una toalla de tela o papel. 3. Drene el agua de los tanques en el fregadero y enjuáguelos completamente. Límpielos frotando con un paño y séquelos con una toalla de tela o de papel. 4. El caso y vuelva a llenar el tanque con agua corriente como se indicó anteriormente en las instrucciones para el llenado. No lo llene de más. 5. Siga las instrucciones de funcionamiento para encender el humidificador. Figura 3 Transductor Base del humidificador Mantenimiento semanal Para extraer el sarro : 1. Repita los pasos previos de mantenimiento diario. 2. Limpie la base llenándola parcialmente con una taza de 250 ml (8 oz.) de vinagre blanco sin diluir o con Cleanse Clean® Solución (Model S1710). Deje reposar esta solución en la base por 20 min. mientras limpia todas las superficies interiores con un cepillo blando (el cepillo no está incluido). Friegue suavemente el área que rodea el transductor (ubicado en la base del humidificador) con un cepillo blando. Quite el sarro frotando la base con un trapo humedecido con vinagre blanco sin diluir. (consulte la Figura 3) 3. Enjuague con agua tibia limpia para extraer la solución limpiadora antes de desinfectar el tanque. Para desinfectar la base y los tanques del humidificador : 1. Llene cada tanque hasta la mitad con agua y 1/2 cucharadita de blanqueador de cloro. 2. Deje que la solución trabaje por 20 minutos, sacudiendo los tanques de vez en cuando. Moje todas las superficies. 3. Vacíe cuidadosamente la base y los tanques después de 20 minutos y enjuague hasta que ya no se pueda detectar el olor a cloro. Seque con una tela limpia o con toalla de papel. 4. Vuelva a llenar el tanque con agua fría y reemplace en la carcasa (vea las instrucciones de llenado, previamente). Siga las Instrucciones de funcionamiento para ENCENDER el humidificador. 5. Para limpiar la base del humidificador, tire todo el agua de acceso. Enjuague concienzudamente para eliminar cualquier sedimento de suciedad. Limpiar y secar con un paño limpio o papel toalla. No utilice utensilios de limpieza de metal que sean limpiadores abrasivos. INSTRUCCIONES PARA GUARDAR ACCESORIOS DE REPUESTO INSTRUCCIONES PARA GUARDAR Cuando no utilice su humidificador durante un período prolongado de tiempo: 1. Limpie y seque bien el humidificador según se detalla anteriormente en la sección: instrucciones de mantenimiento semanales. NO deje agua dentro de la unidad cuando guarde el humidificador. Si queda agua, la unidad podría quedar inutilizable para la próxima temporada. 2. Coloque el humidificador en su empaque original y guárdelo en un lugar fresco y seco. ACCESORIOS DE REPUESTO Puede ordenar accesorios de repuesto de una de las siguientes formas: • Visite su distribuidor local • Valla a www.holmesproducts.com • Llame a servicio al consumidor al 1-800-546-5637 HM2610_12ESM1.indd 2 5/31/12 2:24 PM

  • 1
  • 2

3.
Coloque el tanque nuevamente sobre la base. El tanque
comenzará a vaciarse inmediatamente en la base.
4.
Enchufe el cable de corriente en un tomacorriente de
120 voltios AC.
INSTRUCCIONES DE USO
1. Para encender el humidificador, gire la perilla de
control en el sentido de las agujas del reloj para
generar el nivel más alto de humedad (
).
Continuar girando la perilla en dirección de las
manecillas del reloj producirá un nivel menor de
humedad (
) pero por un tiempo más largo y con
un rendimiento más silencioso.
2. Para apagar la unidad, gire la perilla de control
hasta alcanzar la posición Apagado.
3. Una vez que el tanque se encuentre vacío, apague el
humidificador y desconéctelo del tomacorrientes.
Antes de llenarlo nuevamente, vacíe el tanque y la
base de todo resto de agua (siga las instrucciones de
mantenimiento diario). Luego, siga las instrucciones
de llenado que aparecen previamente para llenar
nuevamente el tanque.
ADVERTENCIA:
NO MUEVA el humidificador cuando
tenga agua en el tanque o en la base. La acción de
movimiento podría activar la boquilla de descarga del
tanque de agua y saturar la base del humidificador. Si
sucediera, el humidificador funcionaría intermitentemente
y dejaría de emitir vapor. En este caso, simplemente
elimine el exceso de agua de la base del humidificador.
NOTAS:
La
posición alta
producirá el máximo nivel de
humedad y una
posición baja
ofrecerá el mayor
tiempo de uso y un funcionamiento más silencioso.
INSTRUCCIONES DE LIMPIEZA Y
MANTENIMIENTO
Los humidificadores proveen confort agregando humedad
al aire seco de los ambientes interiores calefaccionados.
Para beneficiarse al máximo de los humidificadores y
evitar su mal uso, siga todas las instrucciones
cuidadosamente. Tenga en cuenta que éste es un artefacto
eléctrico que requiere atención cuando esté en uso.
Además, si no se siguen las recomendaciones para el
cuidado y mantenimiento, crecerán microorganismos en
el agua dentro de los tanques. Se deben ejecutar
rutinariamente los procedimientos de limpieza que se
indican a continuación para asegurar el funcionamiento
adecuado y eficiente del humidificador que son esenciales
para el rendimiento óptimo constante de la unidad y para
evitar la formación de algas y bacterias.
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
CLEANING AND MAINTENANCE
INSTRUCTIONS
Humidifiers provide comfort by adding moisture to dry, heated
indoor air. To benefit most from the humidifier and avoid
product misuse, follow all instructions carefully. Please note
that this is an electrical appliance and requires attention when
in use.
In addition, if you do not follow the recommended care
and maintenance guidelines, micro-organisms may be
able to grow in the water within the water tank. You must
routinely follow the cleaning procedures that follow in
order to ensure proper, efficient operation of your
humidifier. Proper maintenance and cleaning is essential
to the continued performance of your unit and the
avoidance of algae or bacteria build-up.
Daily Maintenance:
1.
Be sure the unit is OFF and is disconnected from the
electrical outlet.
2.
Carry the base of the unit to the sink, place in sink,
drain any remaining water and rinse thoroughly to
remove any sediment or dirt.
Wipe clean, and dry
with a clean cloth or paper towel.
3.
Drain the water from the tank into the sink and rinse
tank thoroughly. Wipe clean, and dry with a clean
cloth or paper towel.
4.
Replace the
housing, then refill tank with cool tap water
as instructed
earlier in the Filling Instructions. Do not
overfill.
5.
Follow Operating Instructions to turn on the humidifier.
Weekly Maintenance:
To Remove Scale:
1.
Repeat previous steps in Daily Maintenance.
2.
Clean the base by partially filling the base with one
8-oz cups of undiluted white vinegar, or by using
Cleanse Clean
®
Solution (Model S1710) by the
manufacturer. Leave this solution in the base for 20
minutes, while cleaning all the interior surfaces with
a soft brush (brush not included). Gently scrub the
area around the transducer (located at the humidifier
base) with a soft brush. Remove base scale by wiping
the base with a cloth dampened with undiluted white
vinegar. (see Figure 3)
3.
Rinse with clean warm water to remove the cleaning
solution before disinfecting the tank.
To Disinfect Humidifier Base and Tank:
1.
Fill humidifier tank 1/2 full with water and 1/2
tablespoon of chlorine bleach.
2.
Let the solution stand for 20 minutes, swishing every
few minutes. Wet all surfaces.
3.
Carefully empty the tank after 20 minutes, and rinse
with warm water until you cannot detect any bleach
smell. Dry with a clean cloth or paper towel.
4.
Refill the water tank with cool water and replace on
housing (see Filling Instructions above). Follow
Operating Instructions to turn the humidifier ON.
5.
To clean the humidifier base, pour out all access
water. Rise thoroughly to remove any sediment to
dirt. Wipe clean and dry with a clean cloth or paper
towel. Do not use metal cleaning utensils of abrasive
cleansers.
STORAGE INSTRUCTIONS
When not using your humidifier for an extended period
of time:
1.
Clean, rinse and thoroughly dry the humidifier as
directed in weekly maintenance. DO NOT leave any
water in the unit when storing. Leaving water in the
unit may render the unit inoperable for the following
season.
2.
Place the humidifier in the original carton and store
in a cool, dry place.
REPLACEMENT ACCESSORIES
To order the replacement accessories you can do any of
the following:
Visit your local retailer
Go to
www.holmesproducts.com
Call Consumer Service at 1-800-546-5637
22.
Do not plug in the cord with wet hands: electric shock
could result.
23.
Do not pour water in any openings other than the
water tank.
24.
To prevent damage to surfaces, do not place
humidifier under overhanging surfaces.
25.
NEVER operate unit without water in the tank.
26.
Do not move unit after it has been used until unit
cools completely.
27.
Use both hands when carrying full tank of water.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
NOTE:
This is an electrical appliance and requires
attention when in use.
NOTE:
If moisture forms on the walls or windows of the
room, turn off the humidifier. The room already has plenty
of humidity and additional moisture may cause damage.
NOTE:
DO NOT block air inlet or outlet.
Cord and Plug Installation Safety Instructions:
The length of cord used on this appliance was selected to
reduce the hazards of becoming tangled in, or tripping
over a longer cord. If a longer cord is necessary an
approved extension cord may be used. The electrical
rating of the extension cord must be equal to or greater
than the rating of the humidifier (refer to the rating
information placed on the humidifier). Care must be
taken to arrange the extension cord so that it will not
drape over the countertop or tabletop where it can be
pulled on by children or accidentally tripped over.
HOW
ULTRASONIC
WORKS:
An ultrasonic transducer atomizes water, producing
refreshing visible cool mist.
NOTE:
A humidity level below 20% can be unhealthy
and uncomfortable. The recommended humidity level is
between 40%-50%.
PRE-OPERATING INSTRUCTIONS
1.
Be sure the humidifier is switched OFF and the unit is
disconnected from the electrical outlet.
2.
Select a location for your humidifier, on a flat surface,
about 4 inches (10 cm) away from the wall. DO NOT
place the humidifier on a finished floor or near
furniture, which can be damaged by too much moisture
or water. Place on a moisture resistant surface.
FILLING THE WATER TANK
Tank Cap Tablet Holder
The tank cap of the humidifier features a cage that holds
humidifier enhancement tablets. It is located on the tank
cap to ensure all water is treated by the tablet before it
passes through to the base of the humidifier. Pop off the
top of the green cage and place tablet directly inside.
Close the top of the green cage and replace the tank cap
on tank FIRMLY (see Figure 1).
NOTE:
Only one humidifier enhancement tablet should
be used per tank filling. To order more humidifier
enhancement tablets, go to www.holmesproducts.com or
call customer service at 1-800-546-5637.
1.
Remove the tank from the main housing.
2.
Bring the tank to the sink, turn upside down and
twist off the tank cap by turning counterclockwise. Fill
tank with cool, fresh tap water. DO NOT fill with
warm water as this may cause leaking. Replace the
cap on tank FIRMLY.
3.
Place tank back on to the base. The tank will
immediately begin to empty into the base.
4.
Plug the humidifier into a 120V electrical outlet.
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1.
Read all instructions before using the appliance.
2.
To avoid fire or shock hazard, plug the appliance
directly into a 120V AC electrical outlet.
3.
Keep the cord out of heavy traffic areas. To avoid
fire hazard, NEVER put the cord under rugs or near
heat registers.
4.
DO NOT place humidifier near heat sources such as
stoves, radiators, and heaters. DO locate your
humidifier on an inside wall near an electrical outlet.
The humidifier should be at least 4 inches (10 cm)
away from the wall for best results.
5.
NEVER place humidifier in an area where it is
accessible to children. NEVER use humidifier in a
closed room, particularly where a child may be
sleeping, resting, or playing (a closed room may
result in excessive humidity).
6.
WARNING:
Do not attempt to refill humidifier
without first unplugging the unit from its electrical
outlet. Failure to heed this warning may cause
personal injury. Be sure to unplug the unit by pulling
on the plug and not the cord.
7.
Never place anything over moisture outlet when the
unit is running.
8.
NEVER drop or insert any object into any openings.
9.
DO NOT operate any appliance with a damaged cord
or plug, after the appliance malfunctions, or if it has
been dropped or damaged in any manner. Return
appliance to manufacturer for examination, electrical
or mechanical adjustment, or repair.
10.
Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by the
manufacturer may cause hazards.
11.
DO NOT use outdoors.
12.
Always place humidifier on a firm, flat, level surface.
A waterproof mat or pad is recommended for use
under the humidifier. NEVER place it on a rug or
carpet, or on a finished floor that may be damaged
by exposure to water or moisture.
13.
DO NOT allow the Moisture Outlet to directly face the
wall. Moisture could cause damage, particularly to wall
paper.
14.
Humidifier should be unplugged when not in use.
15.
NEVER tilt, move, or attempt to empty unit while it is
operating. Shut off and unplug before removing the
water tank and moving the unit.
16.
This humidifier requires daily and weekly
maintenance to operate appropriately. Refer to daily
and weekly cleaning procedures. Use only cleaners
and additives recommended by the manufacturer.
17.
NEVER use detergents, gasoline, glass cleaner,
furniture polish, paint thinner, or other household
solvents to clean any part of the humidifier.
18.
Excessive humidity in a room can cause water
condensation on windows and some furniture. If this
happens, turn the humidifier OFF.
19.
Do not use humidifier in an area where humidity
level is in excess of 50%. Use a hygrometer,
available at your local retailer or through the
manufacturer, to measure the humidity.
20.
DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed
by qualified personnel only.
21.
Never place housing under water flow or immerse in
liquids.
FEATURES - OPERATIONS
CLEANING / MAINTENANCE
STORAGE INSTRUCTIONS
REPLACEMENT ACCESSORIES
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
OPERATING INSTRUCTIONS
1. To turn the humidifier on, turn the Control Knob
clockwise to produce the highest moisture level (
).
Continuing to turn the knob clockwise will produce
lower moisture level (
) but with longer run time
and quieter performance.
2. To turn off the unit, switch the Control Knob to the
Off position.
3. Once the tank is empty, turn off your humidifier and
unplug it from the electrical outlet. Before refilling,
empty any residual water from the base and the tank
(follow the daily maintenance instructions). Then
follow the above Filling Instructions to refill the tank.
WARNING:
DO NOT move the humidifier with water in
the tank or the humidifier base. The moving action of the
water may activate the water tank’s release nozzle and
overfill the humidifier base. This may cause the
humidifier to function intermittently, or stop emitting
mist. Should this occurs, simply remove the excess water
from the humidifier base.
NOTES:
High
setting will produce the maximum moisture
level and
Low
setting will produce the longest run
time and quieter performance.
CARACTERISTICA - FUNCIONAMIENTO
CARACTERISTICA - FUNCIONAMIENTO
LIMPIEZA Y MANTENIMIENTO
INSTRUCCIONES PARA GUARDAR
ACCESORIOS DE REPUESTO
LEA Y CONSERVE ESTAS IMPORTANTES
INSTRUCCIONES DE SEGURIDAD
ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más
ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica, este
enchufe está diseñado para insertarse en un tomacorriente polarizado en
un solo sentido. Si el enchufe no entra completamente en el tomacorriente,
inviértalo. Si aun así no entra, llame a un electricista calificado para
instalar un tomacorriente apropiado.
NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD
DE NINGUNA MANERA.
Mantenimiento diario
:
1.
Asegúrese de apagar y desenchufar la unidad del
tomacorriente.
2.
Lleve la base de la unidad al fregadero o a la tina,
coloque la base en el fregadero, drene el agua
remanente, enjeague completamente para remover
cualquier sedimento o suciedad, limpie frotando con
un paño y seque con una toalla de tela o papel.
3.
Drene el agua de los tanques en el fregadero y
enjuáguelos completamente. Límpielos frotando con
un paño y séquelos con una toalla de tela o de papel.
4.
El caso y vuelva a llenar el tanque con agua corriente
como se indicó anteriormente en las instrucciones
para el llenado. No lo llene de más.
5.
Siga las instrucciones de funcionamiento para encender
el humidificador.
Mantenimiento semanal
Para extraer el sarro :
1.
Repita los pasos previos de mantenimiento diario.
2.
Limpie la base llenándola parcialmente con una taza
de 250 ml (8 oz.) de vinagre blanco sin diluir o con
Cleanse Clean
®
Solución (Model S1710). Deje reposar
esta solución en la base por 20 min. mientras limpia
todas las superficies interiores con un cepillo blando
(el cepillo no está incluido). Friegue suavemente el
área que rodea el transductor (ubicado en la base del
humidificador) con un cepillo blando. Quite el sarro
frotando la base con un trapo humedecido con
vinagre blanco sin diluir. (consulte la Figura 3)
3.
Enjuague con agua tibia limpia para extraer la
solución limpiadora antes de desinfectar el tanque.
Para desinfectar la base y los tanques del
humidificador :
1.
Llene cada tanque hasta la mitad con agua y 1/2
cucharadita de blanqueador de cloro.
2.
Deje que la solución trabaje por 20 minutos, sacudiendo
los tanques de vez en cuando. Moje todas las superficies.
3.
Vacíe cuidadosamente la base y los tanques después
de 20 minutos y enjuague hasta que ya no se pueda
detectar el olor a cloro. Seque con una tela limpia o
con toalla de papel.
4.
Vuelva a llenar el tanque con agua fría y reemplace
en la carcasa (vea las instrucciones de llenado,
previamente). Siga las Instrucciones de
funcionamiento para ENCENDER el humidificador.
5.
Para limpiar la base del humidificador, tire todo el agua
de acceso. Enjuague concienzudamente para eliminar
cualquier sedimento de suciedad. Limpiar y secar con un
paño limpio o papel toalla. No utilice utensilios de
limpieza de metal que sean limpiadores abrasivos.
INSTRUCCIONES PARA GUARDAR
Cuando no utilice su humidificador durante un período
prolongado de tiempo:
1.
Limpie y seque bien el humidificador según se detalla
anteriormente en la sección: instrucciones de
mantenimiento semanales. NO deje agua dentro de
la unidad cuando guarde el humidificador. Si queda
agua, la unidad podría quedar inutilizable para la
próxima temporada.
2.
Coloque el humidificador en su empaque original y
guárdelo en un lugar fresco y seco.
ACCESORIOS DE REPUESTO
Puede ordenar accesorios de repuesto de una de las
siguientes formas:
Visite su distribuidor local
Valla a
www.holmesproducts.com
Llame a servicio al consumidor al
1-800-546-5637
realizada únicamente por personal calificado.
21. Nunca coloque el gabinete debajo de la canilla o lo
sumerja en líquidos.
22. No enchufe el cable con las manos húmedas. Puede
ocasionarle una descarga eléctrica.
23. No coloque agua en ninguna abertura que no sea el
tanque de agua.
24. Para prevenir el daño a las superficies, no coloque el
humidificador debajo de ninguna superficie que
sobresalga por encima del mismo.
25.
NUNCA haga funcionar la unidad sin agua en el tanque.
26. Una vez utilizada la unidad, no la mueva hasta que
se haya enfriado completamente.
27. Use las dos manos cuando cargue el tanque de agua.
LEA Y CONSERVE ESTAS
IMPORTANTES
INSTRUCCIONES DE
SEGURIDAD
INFORMACIÓN DE SEGURIDAD PARA EL
CONSUMIDOR
NOTA:
Este es un artefacto eléctrico y requiere ser usado
con cuidado.
NOTA:
Si se acumula humedad en las paredes o
ventanas del cuarto, apague el humidificador. El cuarto
ya tiene demasiada humedad y la humedad adicional
puede causar daños.
NOTA:
NO bloquee la entrada o salida de aire.
Instrucciones de Seguridad en la Instalación del
Cable y el Enchufe :
La longitud del cable de este artefacto fue seleccionada
para reducir el riesgo de enredarse o tropezarse con un
cable más largo. Si necesita usar un cable más largo,
puede utilizar un cable de extensión aprobado. La
capacidad eléctrica del cable de extensión debe ser igual o
mayor que la capacidad del humidificador (consulte la
información sobre clasificación que se encuentra en el
humidificador). No debe permitir que el cable de extensión
cuelgue de la mesada o mesa de tal forma que pueda ser
jalado por niños o causar que alguien se tropiece.
CÓMO FUNCIONA
ULTRASONIC
:
Un transductor ultrasónico atomiza el agua y produce un
refrescante vapor frío y visible.
NOTA:
Un nivel de humedad menor al 20% puede ser
nocivo e incómodo. El nivel de humedad recomendado es
entre el 40% y el 50%.
INSTRUCCIONES PREVIAS AL USO
1.
Asegúrese de que el humidificador esté en OFF
(Apagado) y desenchúfelo del tomacorriente.
2.
Elija un lugar para su humidificador, en una
superficie plana, aproximadamente a 4 pulgadas de
distancia de la pared. NO coloque el humidificador
sobre un piso pulido o cerca de algún mueble, ya que
lo puede dañar por el exceso de humedad o agua.
Colóquelo sobre una superficie resistente a la humedad.
COMO LLENAR EL TANQUE DE AGUA
Compartimiento del tapón del tanque para
tabletas
El tapón del tanque del humidificador cuenta con un
compartimiento en el que se pueden colocar tabletas
intensificadoras del humidificador. Se encuentra ubicado
en el tapón del tanque a fin de garantizar que toda el
agua sea tratada con la tableta antes de pasar a través
de la base del humidificador. Levante la parte superior
del compartimiento verde y coloque la tableta
directamente en el interior. Cierre la parte superior del
compartimiento y reemplace el tapón del tanque en el
tanque CON FIRMEZA (vea la Figura 1).
NOTA:
Se debe usar solo una tableta intensificadora del
humidificador por llenado del tanque. Para solicitar más
tabletas intensificadoras del humidificador, visite
www.holmesproducts.com o llame al servicio de atención
al cliente al 1-800-546-5637.
1.
Retire el tanque de la caja principal.
2.
Acerque el tanque hasta la pileta, délo vuelta y
desenrosque la tapa del tanque girando en sentido
contrario a las agujas del reloj. Llene el tanque con
agua fría del grifo. NO llene con agua caliente ya
que esto puede producir una pérdida. Vuelva a
colocar la tapa del tanque CON FIRMEZA.
Debe tomar precauciones básicas de seguridad siempre que
utilice artefactos eléctricos para reducir el riesgo de incendio,
descarga eléctrica y daños personales, incluyendo lo
siguiente:
1.
Lea completamente las instrucciones antes de utilizar
el artefacto.
2.
Para evitar incendio o descarga eléctrica, enchufe el
artefacto directamente en un tomacorriente de 120V CA.
3.
Mantenga el cable fuera de las zonas de mucho
tráfico. Para evitar incendios, NUNCA coloque el cable
debajo de alfombrillas o cerca de salidas de calefacción.
4.
NO coloque el humidificador cerca de fuentes de calor
como estufas, radiadores y calefactores. NO coloque el
humidificador contra una pared interna cerca de un
tomacorriente. El humidificador debe estar a por lo
menos 4" de la pared para obtener el mejor resultado.
5.
NUNCA coloque el humidificador en una zona
accesible para los niños. NUNCA use el humidificador
en un cuarto cerrado, especialmente donde pueda
haber un niño durmiendo, descansando, o jugando
(un cuarto cerrado puede resultar en excesiva humedad).
6.
ADVERTENCIA:
No intente llenar nuevamente el
humidificador sin antes desenchufarlo del tomacorriente.
El no tener en cuenta esta advertencia puede causar
daños personales. Asegúrese de desenchufar la unidad
tirando del enchufe y no del cable.
7.
Nunca coloque algo sobre la salida de humedad
cuando la unidad esté funcionando.
8.
NUNCA inserte ningún objeto en una de las ranuras.
9.
NO utilice ningún artefacto si el cable o el enchufe
están dañados, luego de una falla, o si se ha caído o
ha sufrido cualquier tipo de daño. Devuelva el
artefacto al fabricante para su inspección, ajuste
eléctrico o mecánico, o reparación.
10.
Utilice el artefacto únicamente para el propósito
hogareño indicado en este manual. Cualquier uso
distinto al recomendado por el fabricante puede
causar incendio, descarga eléctrica, o daños
personales. El uso
de accesorios no recomendados o
que no sean vendidos por el fabricante puede ser
peligroso.
11. NO utilizar en el exterior.
12. Siempre coloque el humidificador en una superficie
firme, plana y nivelada. Se recomienda el colocar
una alfombrilla o bandeja resistente al agua debajo
del humidificador. NUNCA lo coloque sobre un tapete
o una alfombra, o en un piso que pueda dañarse con
el agua o la humedad.
13. NO haga que la salida de humedad apunte
directamente a la pared. La humedad puede causar
daños, especialmente al empapelado.
14. Se debe desenchufar el humidificador cuando no se usa.
15. NUNCA incline, mueva o intente vaciar la unidad
mientras esté funcionando. Apague y desenchufe la
unidad antes de quitar el tanque de agua y moverla.
16. Este humidificador requiere mantenimiento diario y
semanal para funcionar correctamente. Refiérase a
los procedimientos de limpieza diarios y semanales.
Use únicamente limpiadores y aditivos recomendados
por el fabricante.
17. NUNCA use detergentes, gasolina, limpiavidrios,
limpiador de muebles, diluyente de pintura u otro
solvente hogareño para limpiar ninguna parte del
humidificador.
18. La humedad excesiva en un cuarto puede causar
condensación de agua en las ventanas y en algunos
muebles. Si sucede esto, apague el humidificador.
19. No use el humidificador en un área donde el nivel de
humedad es mayor al 50%. Use un Higrómetro,
disponible en su tienda local o a través del
fabricante, para medir la humedad.
20. NO intente reparar o ajustar ninguna función
eléctrica o mecánica de esta unidad. El hacerlo
invalidará la garantía. La unidad no contiene partes
reparables por el usuario. Toda reparación debe ser
Figure 2
A. Carry Handle
B. Water Tank
C. Humidifier Housing
D. Humidifier Base
E.
Control Knob
F.
Tank Cap with the
Cage
A
B
C
D
E
F
A
B
C
D
E
F
Figura 2
A. Manija de traslado
B. Tanque de agua
C. Cubierta del
humidificador
D. Base del
humidificador
E.
Perilla de control
F.
Tapón del tanque con
el compartimiento
Figure 3
Transducer
Humidifier Base
Figura 3
Transductor
Base del humidificador
Figure 1
Tank Cap
Place tablet inside
Pop off the
cage top
Figura 1
Tapón del tanque
Coloque la tableta en el interior
Quite la parte
superior del
compartimiento
HM2610_12ESM1.indd
2
5/31/12
2:24 PM