Homelite HOMBL10VNM User Manual - Page 9

Operation, Warning

Page 9 highlights

OPERATION APPLICATIONS You may use this product for the purposes listed below:  Keeping decks and driveways free from grass clippings, leaves, pine needles, and other debris CHARGING THE TOOL See Figure 3.  Place the ON/OFF switch in the OFF ( O ) position.  Insert the charging cable into the product as shown.  Connect the power adapter to an outlet providing normal household voltage, 120 volts, AC only, 60 Hz.  When the tool is charging, the LED will turn red.  Do not place tool in an area of extreme heat or cold. It will charge best at normal room temperature.  If the LED does not turn on after connecting to a power supply, check connections. If all connections are secure, remove from power supply and recheck after one hour.  After charging is complete, the LED will turn green.  If LED does not turn to green after three hours, an error has occurred. If all connections are secure, remove from power supply and recheck after one hour.  Disconnect the power adaptor from the outlet once the tool is fully charged and ready for use.  Disconnect the charging cable from the tool. WARNING: Do not use charger outdoors or expose to wet or damp conditions. Water entering charger will increase the risk of electric shock. STARTING/STOPPING THE BLOWER See Figure 4.  To start the blower, place the ON/OFF switch in the ON ( l ) position.  To stop the blower, place the ON/OFF switch in the OFF ( O ) position. OPERATING THE BLOWER See Figure 5. n To keep from scattering debris, blow around the outer edges of a debris pile. Never blow directly into the center of a pile. n To reduce sound levels, limit the number of pieces of equipment used at any one time. n Use rakes and brooms to loosen debris before blowing. In dusty conditions, slightly dampen surfaces when water is available. n Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens. n Watch out for children, pets, open windows, or freshly washed cars, and blow debris safely away. n After using blowers or other equipment, CLEAN UP! Dispose of debris properly. WARNING: Battery tools are always in operating condition. Therefore, switch should always be in the OFF position when not in use or carrying at your side. WARNING: Do not charge the battery in a damp or wet location. Do not use, store, or charge battery packs or products in locations where the temperature is less than 50°F or more than 100°F. Do not store outside or in vehicles. Page 7 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30

Page 7 — English
OPERATION
STARTING/STOPPING THE BLOWER
See Figure 4.
To start the blower, place the ON/OFF switch in the ON
( l )
position.
To stop the blower, place the ON/OFF switch in the OFF
( O )
position.
OPERATING THE BLOWER
See Figure 5.
To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the center
of a pile.
To reduce sound levels, limit the number of pieces of
equipment used at any one time.
Use rakes and brooms to loosen debris before blowing.
In dusty conditions, slightly dampen surfaces when water
is available.
Conserve water by using power blowers instead of hoses
for many lawn and garden applications, including areas such
as gutters, screens, patios, grills, porches, and gardens.
Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
After using blowers or other equipment, CLEAN UP!
Dispose of debris properly.
WARNING:
Battery tools are always in operating condition. Therefore,
switch should always be in the OFF position when not in
use or carrying at your side.
APPLICATIONS
You may use this product for the purposes listed below:
Keeping decks and driveways free from grass clippings,
leaves, pine needles, and other debris
CHARGING THE TOOL
See Figure 3.
Place the ON/OFF switch in the OFF
( O )
position.
Insert the charging cable into the product as shown.
Connect the power adapter to an outlet providing normal
household voltage, 120 volts, AC only, 60 Hz.
When the tool is charging, the LED will turn red.
Do not
place tool in an area of extreme heat or cold. It
will charge best at normal room temperature.
If the LED does not turn on after connecting to a power
supply, check connections. If all connections are secure,
remove from power supply and recheck after one hour.
After charging is complete, the LED will turn green.
If LED does not turn to green after three hours, an error
has occurred. If all connections are secure, remove from
power supply and recheck after one hour.
Disconnect the power adaptor from the outlet once the
tool is fully charged and ready for use.
Disconnect the charging cable from the tool.
WARNING:
Do not use charger outdoors or expose to wet or damp
conditions. Water entering charger will increase the risk
of electric shock.
WARNING:
Do not charge the battery in a damp or wet location. Do
not use, store, or charge battery packs or products in
locations where the temperature is less than 50°F or more
than 100°F. Do not store outside or in vehicles.