Honeywell 6151 Installation Guide - Page 3
option. The Zone Expander Address field will - programming
View all Honeywell 6151 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
The keypad options may only be programmed within 60 seconds of applying power. After that, they are not accessible for editing or viewing. The Address can still be viewed by holding down the 1 and 3 keys for approximately three (3) seconds. To re-enter programming mode, remove and reapply power and proceed as follows: Perform the following steps to change the keypad options. You must enter all options in order for the entries to be saved. Use the [✲] key to advance through the options. 1. Enter the keypad's local program mode within 60 seconds of power-up by pressing and holding down the [1] and [3] keys at the same time for 3 seconds. The following will be displayed: 31 2. The current keypad address will be displayed with the cursor under the "tens" digit. If the current keypad address setting is acceptable (the default = 31), press the [✲] key to advance to the Zone Expander Enable field and go to step 3. To change the current keypad address, first reset the current address to "00" as follows: press [0] to clear the "tens" digits. The cursor will move to the "ones" digit position. Press [0] again to clear the "ones" digit. The cursor will move back to the "tens" digit position. Now set the desired keypad address as follows: Enter the proper "tens" digit for the keypad's address. The cursor will move to the "ones" digit. Enter the proper "ones" digit for the keypad's address. If you connect more than one keypad, on control panels that support addressable keypads (i.e., VISTA-10P/15P/20P), you must ensure that a unique address has been programmed for each keypad. Press the [✲] key to store the displayed address and to advance to the Zone Expander Enable field. The following will be displayed: EO 3. By pressing the [1] or [0] key, you can toggle the Zone Expander Enable option (default = OFF, O). a. To use the zone contacts, set the option to ON [1]. Use the [✲] key to advance to the next option. The Zone Expander Address field will appear. Go to step 4. b. To use the 6151as a regular keypad set the option to OFF [0]. Use the [✲] key to advance to the next option. The Tamper field will appear. Go to step 6. In order to use the built-in zone, you must enable a 4219 zone expander in the panel. Each expander address takes up eight zones (i.e., if using two 6151 s, zone 9 would be on module address 07, and zone 17 would be on module address 08). Unused module zones can still be used for wireless devices. 107 4. Set the Expander device address in the same way as the keypad address (Default = 07). Consult the control panel's installation guide to select the correct address. Use the [✲] key to advance to the Zone Supervision type option. The following will be displayed: A 1 5. By pressing the [1] or [0] key, you can toggle the zone supervision type option. Either conventional EOL resistor supervised zone or double-balanced zones (see Figure 3) may be selected. Enter [1] to select EOLR or [0] to select double balanced (default = conventional EOLR, 1). Consult the panel's installation guide for proper zone type selection. Use the [✱] key to advance to the Tamper option. The following will be displayed: bD 6. Enter [1] to enable the tamper feature or enter [0] to disable the feature (default = 0 - disabled). Use the [✲] key to advance to the LCD display option. The following will be displayed: c 1 7. By pressing either the [1], [2], or [3] keys you can select the LCD display option (default = 1). Option 1: The display is always active (default = 1). Option 2: The display and LEDs are blanked until a key is pressed, then displays for 45 seconds after the last key was pressed. Option 3: The display and LEDs are blanked 45 seconds after the panel is armed and remains blanked until the panel is disarmed (default = 1). Use the [✲] key to advance to the Sounds option. d 1 8. By pressing the [1] key, you can toggle the Sounds option (default = 1). Option 1: To produce all sounds set the option to ALL SOUNDS (default = 1). Option 2: To produce only key click and alarm sounds set the option to ALARM. WWW.DIYWALWARMWFO.RUDM.ICOYM ALA-R3 -MFORUM.COM