Honeywell HZ3220BW Owners Manual - Page 2

Set-up, Operation, Assembly, Electrical Rating - thermostat

Get Honeywell HZ3220BW - Electronic Tower Surround Heater PDF manuals and user guides
UPC - 092926344665
View all Honeywell HZ3220BW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

ASSEMBLY • Remove the Handle from the box. • Place the heater on a firm, level floor. • Line up the prongs on the bottom of the handle with the openings on the top of the heater and firmly push down (Fig. 1). The handle is now permanently fastened to the top cover. Fig. 1 SET-UP • Place the heater on a firm, level, open surface free from Fig. 2 obstructions and at least 3 feet (0.9m) away from any wall or any combustible material. DO NOT use on an unstable surface such as bedding or deep carpeting. BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY SMALL CHILDREN OR PETS. 360° Heating • The Tower Surround Heater is designed to disperse heat in either a 360° range or in one direction only. • To select the desired heating mode, slide the Direction Control switch, located on the top of the heater, to the position of your choice (Fig. 2): - to the left (full circle) for 360° Heating - to the right (half circle) for Forward Only Heating (One Direction Heating) Forwad Only Heating (One Direction Heating) OPERATION • Select the appropriate heat dispersion mode (See Set-Up). Fig. 3 • With the Power knob in the OFF (O) position, plug the heater into a polarized 120V outlet. • Turn the Thermostat control fully clockwise to the HIGH setting. • This heater is equipped with three different heat settings. The Low setting (I) uses 600 watts of power, the Medium setting (II) uses 900 watts of power and the High setting (III) uses 1500 watts of power. You can select the proper setting to accommodate your comfort level. Because the Low and Medium heat settings do not require as much electricity to operate, they are more energy efficient and may be better options if you are concerned about the amperage draw on a circuit when the heater is in the High setting. • Turn the heater on using the Child Resistant switch (Power knob). To operate the switch, push down the two sides of the Power knob while turning it clockwise to the desired position (Fig. 3). The power light will illuminate. The Child Resistant switch helps to keep the heater from being turned on unintentionally. • When the room reaches a comfortable temperature, slowly turn the Thermostat control counterclockwise until the heater goes off. This is the point at which the Thermostat setting equals the room temperature. At this setting, the Thermostat will automatically turn the heater on and off to maintain this selected temperature. • Push down and turn the Power knob to OFF and unplug the heater when you are finished using it. ELECTRICAL RATING This product is rated 12.5 Amps (1500 watts) @ 120V, 60Hz

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
•
Place the heater on a firm, level, open surface free from
obstructions and at least 3 feet (0.9m) away from any wall or any
combustible material.
DO NOT
use on an unstable surface such as
bedding or deep carpeting.
BE SURE THE HEATER IS NOT IN A
POSITION WHERE IT MAY BE TRIPPED OVER BY SMALL
CHILDREN OR PETS.
•
The Tower Surround Heater is designed to disperse heat in either a
360° range or in one direction only.
•
To select the desired heating mode, slide the Direction Control
switch, located on the top of the heater, to the position of your choice (Fig. 2):
– to the left (full circle) for
360° Heating
– to the right (half circle) for
Forward Only Heating (One Direction Heating)
SET-UP
OPERATION
•
Select the appropriate heat dispersion mode (See
Set-Up
).
•
With the Power knob in the OFF (O) position, plug the heater into
a polarized 120V outlet.
•
Turn the Thermostat control fully clockwise to the HIGH setting.
•
This heater is equipped with three different heat settings. The
Low setting (I) uses 600 watts of power, the Medium setting (II)
uses 900 watts of power and the High setting (III) uses 1500
watts of power. You can select the proper setting to
accommodate your comfort level. Because the Low and Medium
heat settings do not require as much electricity to operate, they
are more energy efficient and may be better options if you are concerned about the amperage
draw on a circuit when the heater is in the High setting.
•
Turn the heater on using the Child Resistant switch (Power knob). To operate the switch,
push
down
the two sides of the Power knob while turning it clockwise to the desired position (Fig. 3).
The power light will illuminate. The Child Resistant switch helps to keep the heater from being
turned on unintentionally.
•
When the room reaches a comfortable temperature, slowly turn the Thermostat control counter-
clockwise until the heater goes off. This is the point at which the Thermostat setting equals the
room temperature. At this setting, the Thermostat will automatically turn the heater on and off to
maintain this selected temperature.
•
Push down and turn the Power knob to OFF and unplug the heater when you are finished
using it.
ASSEMBLY
•
Remove the Handle from the box.
•
Place the heater on a firm, level floor.
•
Line up the prongs on the bottom of the handle with the openings on the
top of the heater and firmly push down (Fig. 1).
The handle is now
permanently fastened to the top cover.
Forwad Only
Heating
(One Direction
Heating)
360° Heating
Fig. 1
Fig. 2
Fig. 3
ELECTRICAL RATING
This product is rated 12.5 Amps (1500 watts) @ 120V, 60Hz