Honeywell VISTA 15P User Guide

Honeywell VISTA 15P - Ademco 6 Zone Control Panel Manual

Get Honeywell VISTA 15P - Ademco 6 Zone Control Panel PDF manuals and user guides
UPC - 781410414846
View all Honeywell VISTA 15P manuals
Add to My Manuals
Save this manual to your list of manuals

Honeywell VISTA 15P manual content summary:

  • Honeywell VISTA 15P | User Guide - Page 1
    ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems User Guide K5309-1V4 10/04 Rev. A National Security Systems Inc (800) 457-1999
  • Honeywell VISTA 15P | User Guide - Page 2
    when used with your Honeywell security system. About This Manual This manual is a step-by-step guide that will acquaint you with the system's features and benefits. It defines the components and their functions, describes their operation, and provides clear step-by-step instructions for normal and
  • Honeywell VISTA 15P | User Guide - Page 3
    the Voice Message Center ...7 About The Keypads ...8 General Information...8 Fixed-Word Display Keypad ...10 Functions of the Keypads ...11 Entry/Exit Delays ...14 Entry Delay...14 Exit Delay ...14 Exit Alarms...15 Checking For Open Zones ...16 Using the [∗] Key to Display and Announce System Status
  • Honeywell VISTA 15P | User Guide - Page 4
    ...29 Paging Feature ...30 About Automatic Paging ...30 About Manual Paging...31 Latch Key Paging ...31 Security Codes & Authority Levels...32 About Security Codes ...32 Authority Level Definitions ...32 How to Assign User Codes and Attributes 33 Accessing Other Partitions (VISTA-20P Series 34
  • Honeywell VISTA 15P | User Guide - Page 5
    systems may not include fire protection - check with your installer. NOTE: Features and procedures described in this manual apply to the VISTA-20P/VISTA-20PSIA (VISTA-20P series) and VISTA-15P/VISTA-15PSIA (VISTA-15P series) security systems. Differences are noted where applicable. System Basics
  • Honeywell VISTA 15P | User Guide - Page 6
    keypad when an alarm or trouble condition occurs on a sensor. • Partitions (VISTA-20P Series) provide two independent areas of protection, with each partition containing a group of zones that can be armed and disarmed without affecting other zones or users. • Partitioned systems (VISTA-20P Series
  • Honeywell VISTA 15P | User Guide - Page 7
    pager, display Time/Date, and start a programmed Macro sequence. Paging Feature • If programmed, the system can automatically send certain system condition messages to up to four (VISTA-20P Series) or two (VISTA-15P Series) pagers. • The pager displays code numbers identifying the type of condition
  • Honeywell VISTA 15P | User Guide - Page 8
    in a dimly lit area. • Some keypads have a voice feature that announces the nature and location of all system occurrences. Voice keypads also announce any faulted entry/exit or perimeter zone when Chime mode is on. Ask your installer if this option has been programmed for your system. IMPORTANT: If
  • Honeywell VISTA 15P | User Guide - Page 9
    Alpha Display Keypad 6150-00-001-V0 6160-00-001-V0 ARMED READY MESSAGE MIC 1 OFF RECORD 4 MAX 2 AWAY VOLUME 5 TEST 3 STAY PLAY 6 BYPASS 7 INSTANT 8 CODE 9 CHIME READY STATUS 0 VOICE # FUNCTION Voice-Capable Alpha Display Keypad 6160V-00-006-V0 National Security Systems Inc (800
  • Honeywell VISTA 15P | User Guide - Page 10
    of zone number in trouble. Appears when a fire alarm is generated. Accompanied by a display of the zone in alarm. A FIRE display also appears when a fire alarm is manually activated, accompanied by a display of the fire emergency key zone number. Appears when an alarm has been silenced by the Code
  • Honeywell VISTA 15P | User Guide - Page 11
    15 MESSAGE MIC Functions of the Keypads 1 2 3 4 5 1 OFF 2 AWAY 3 STAY 6 RECORD VOLUME PLAY 7 4 MAX 5 TEST 6 BYPASS 8 9 7 INSTANT 8 CODE the procedures in this manual. • If you make a mistake while entering a security code, stop, press the [✱] key, and then start over.
  • Honeywell VISTA 15P | User Guide - Page 12
    display area. 2. 1 OFF Disarms burglary portion of the system, silences alarms and audible trouble indicators, and clears visual display after problem's correction. [RECORD] On Voice keypads, used in conjunction with the FUNCTION and VOICE keys to record up to a 2.5minute message. 3. 2 AWAY Arms the
  • Honeywell VISTA 15P | User Guide - Page 13
    time annunciates and displays system and/or zone faults (if they exist). 14. KEYS 0-9: Used to enter your security code(s) and to perform their associated system functions after the security code has been entered. 15. MIC On voice keypads, microphone for Message Center recordings. 16. MESSAGE
  • Honeywell VISTA 15P | User Guide - Page 14
    security while on the premises or while away for extended periods of time. See your installer for your delay times. Partition 1 Exit Delay: seconds Entry Delay 1: seconds Entry Delay 2: seconds NOTE: Entry/Exit times set for partition 1 also apply to the Common Zone of the VISTA-20P
  • Honeywell VISTA 15P | User Guide - Page 15
    (after the installer-programmed dial delay expires). The alarm message along with a faulted zone number is displayed on the keypad. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time. - 15 - National Security Systems Inc
  • Honeywell VISTA 15P | User Guide - Page 16
    a "Not Ready" message. Use the READY key to display all faulted zones, making it easier for you to identify and secure any open zone. 1. Press [✱] (do not enter code first) to display faulted zones. 2. Secure or bypass the zones displayed. The keypad's READY indicator lights when all protection
  • Honeywell VISTA 15P | User Guide - Page 17
    sounding an alarm. NIGHT-STAY Mode: Arms Perimeter Only, Plus Selected Zones • Use NIGHT-STAY mode to provide increased security while staying inside. • Arms same as STAY mode, but also arms preselected interior sensors (programmed by your installer), while other interior sensors are left disarmed
  • Honeywell VISTA 15P | User Guide - Page 18
    this feature is set for your system. Quick Arming If "Quick Arming" was programmed by the installer, the [#] key can be pressed in place of the security code when arming the system in any of the arming modes (except NightStay). However, the security code must always be used when manually disarming
  • Honeywell VISTA 15P | User Guide - Page 19
    The "A", "B", "C", and/or "D" keys on your keypad may have been programmed for single-button arming. Note that while it is not necessary to use a security code for arming (by using the Quick Arm method described previously), a security code must always be used when manually disarming the system. If
  • Honeywell VISTA 15P | User Guide - Page 20
    more zones are open). Red Light: Lights or flashes when system is armed in AWAY or STAY mode. See your installer for alarm has occurred (memory of alarm). Before arming, close all perimeter doors and windows. To arm in the AWAY mode: Turn the key to the right for 1/2 second and release. Keypads
  • Honeywell VISTA 15P | User Guide - Page 21
    Alarm and Clear a Memory of Alarm Enter your security code and press the OFF key to silence the alarm (or warning tones of a Memory of Alarm). Note the zone in alarm on the keypad display, and correct the problem (close door, window, etc.). After correcting the problem, enter the security code
  • Honeywell VISTA 15P | User Guide - Page 22
    manually bypass them). However, if a vent zone window is closed after arming, it becomes protected and will cause an alarm if opened again while the system is armed. When bypassing zones "ZONE BYPASSED." To display bypassed zones prior to arming, enter your security code and press the [6] BYPASS key.
  • Honeywell VISTA 15P | User Guide - Page 23
    If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. This feature is useful if, for example, you routinely leave certain windows open when arming at night. 1. + 6 BYPASS + [#] Alpha Display: (Security Code) In
  • Honeywell VISTA 15P | User Guide - Page 24
    the keypad whenever a perimeter door or window is opened. • Interior zones do not produce a tone when they are faulted. • Pressing the READY key will display the open protection points. • Chime mode can be used only while the system is disarmed. To turn Chime Mode on: + 9 CHIME (Security Code) The
  • Honeywell VISTA 15P | User Guide - Page 25
    and Time The system lets you view its time and date setting on an alpha keypad. + [#] + [6] [3] (Security Code) OR, Press the function key (A, B, C, or D) for viewing current date and time, if programmed. Alpha Display: ∗∗∗∗DISARMED READY TO ARM A typical time/date display is shown. The display
  • Honeywell VISTA 15P | User Guide - Page 26
    INSTANT READY 2 AWAY 5 TEST 8 CODE 0 3 STAY 6 BYPASS 9 CHIME # PRESS BOTH KEYS OF DESIRED PAIR AT THE SAME TIME ZONE 96 6160-00-003-V0 6160-00-004-V0 D ZONE 99 Lettered Panic Keys Panic Key Pairs See your installer and use the chart provided in the Features Programmed in Your System section
  • Honeywell VISTA 15P | User Guide - Page 27
    the chart at the back of this manual for the key(s) assigned for macros. 1. + [#] + [6] + [6] (Security Code) Alpha Display: ∗∗∗∗DISARMED READY TO ARM 2. Enter the macro number (1-4 for VISTA-20P Series; 12 for VISTA-15P Series) to be programmed at the "Select Macro?" prompt. Remember, only
  • Honeywell VISTA 15P | User Guide - Page 28
    60203F#701 60203F#701F 60203F#701F2 60203F#701F2F Using a Programmed Macro Key ∗∗∗∗DISARMED READY TO ARM ENTER USER CODE 1. Press the Macro key programmed for the desired series of commands for at least 2 seconds. The "Enter User Code" prompt appears. The prompt remains displayed for up to
  • Honeywell VISTA 15P | User Guide - Page 29
    commands described below. • See your installer for a list of devices that may be set up for your system. A list of these devices is provided at the back of this manual for you to fill out. To Activate Devices: + [#] + [7] + 2-digit device number (Security Code) Devices associated with that device
  • Honeywell VISTA 15P | User Guide - Page 30
    -20P Series, 2 pagers for VISTA-15P Series) as certain conditions occur in your system. • The following events can be programmed by your installer to be sent to the pagers: arming and disarming†, alarms, and trouble conditions. († reports when arming/disarming from a keypad using a security code
  • Honeywell VISTA 15P | User Guide - Page 31
    Paging Feature (cont'd) About Manual Paging Your system may be set up so you can manually send a message to up to four (VISTA20P Series) or two (VISTA-15P Series) pagers. • Your installer programs the paging function key and the pager phone numbers. • Pressing the paging keys sends the message 9 9
  • Honeywell VISTA 15P | User Guide - Page 32
    VISTA-15P Series provides 31 additional codes). • Only the System Master and Partition Master can assign user codes to users. • Users are identified by 2-digit user numbers and are pre-assigned to either partition 1 or partition 2 (VISTA-20P Series). • Only the Installer or System Master can change
  • Honeywell VISTA 15P | User Guide - Page 33
    of user programming. NOTE: Partition Master codes (VISTA-20P Series only) apply only to those user numbers previously assigned (by the system master/installer) to the partition master's partition. Add User Code: (Users 03/33 are preset to partition programmers, but can be changed.) Delete User Code
  • Honeywell VISTA 15P | User Guide - Page 34
    Accessing Other Partitions (VISTA-20P) About Accessing Partitions (GOTO Command and Multi-Partition Arming) Each keypad is assigned a default partition for display purposes, and will show only that partition's information. • If the user is authorized, a keypad in one partition can be used to
  • Honeywell VISTA 15P | User Guide - Page 35
    Display: Green LED lit Multi-Partition Arming (VISTA-20P) Some users can be given Multi-Partition arming ability by being assigned to both partitions when programming user attributes. When attempting to arm multi-partitions: • You must use an Alpha keypad. • The system arms only if all partitions
  • Honeywell VISTA 15P | User Guide - Page 36
    Accessing Other Partitions (cont'd) Common Zone Operation (VISTA-20P) Ask your installer if a "common zone" was assigned. If so, check this box Your system may have been set up to use a common zone, which is an area shared by users of both partitions, such as a foyer or lobby. If so, please note
  • Honeywell VISTA 15P | User Guide - Page 37
    (Master Code) 1 DISARMED READY TO ARM 2. Enter a 2-digit schedule number from: 01-16 (VISTA-20P Series) or 01-04 (VISTA-15P Series) ENTER SCHED NO. Press [∗] to continue. 00=QUIT 00 3. Enter the desired 2-digit event number from the list: 00 = clear the scheduled event 01 = turn a programmed
  • Honeywell VISTA 15P | User Guide - Page 38
    = 00-59 AM = 0; PM = 1 Days = Position the cursor under the desired days using the [∗] key to move forward, then press "1" to select the day. Press [∗] to continue. 8. If applicable, enter the event REPEAT OPTION 0-4 X RANDOMIZE 0=NO 1=YES X - 38 - National Security Systems Inc (800) 457-1999
  • Honeywell VISTA 15P | User Guide - Page 39
    Logging The system records various events in a history log, which can be viewed by the master user on an Alpha Display keypad. • The Event Log holds up to 100 (VISTA-20P Series) or 50 (VISTA-15P Series) events. • Events are displayed in chronological order, from most recent to oldest. • When the
  • Honeywell VISTA 15P | User Guide - Page 40
    ECP Cover Tamper RF Receiver Jam Telco Line Fault Long Range Radio Trouble Fire Loop Trouble Exit Error Alarm Global Trouble, Trouble Day/Night RF Supervision Trouble Supervision Auxiliary Wire Zone RF Sensor Tamper RF Sensor Low-battery Clean Me Code 401 403 406 407 408 409 441 442 459 570 601 602
  • Honeywell VISTA 15P | User Guide - Page 41
    that if wireless motion detectors are used, there is a 3-minute delay between activations. This conserves battery life. 6. Test all smoke detectors, following the manufacturer's instructions. The identification of each detector should appear on the display when each is activated. If a problem is
  • Honeywell VISTA 15P | User Guide - Page 42
    are not. If the problem has been corrected, the display can be cleared if you enter the OFF sequence (security code plus OFF key) twice. If the display persists, CALL FOR SERVICE. Note: A display of CHECK 70 on Alpha Display keypads indicates that the wiring connection to the external sounder is
  • Honeywell VISTA 15P | User Guide - Page 43
    which may impede reception from wireless sensors.** ALARM 1xx FAULT 1xx CHECK 1xx (or 91) Indicates a communication problem between the control and a connected device (e.g., RF receiver, zone expander) where the "xx" indicates the device address. CALL FOR SERVICE. MODEM COMM (or CC) Indicates
  • Honeywell VISTA 15P | User Guide - Page 44
    . If upon disconnection of the control, there is still a problem on the phone line, notify the Telephone Company that they have a problem and request prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the security system. Repairs must be made
  • Honeywell VISTA 15P | User Guide - Page 45
    by pressing the OFF key, but the keypad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your wireless sensors. When you replace the weak battery with a fresh one, the sensor sends a "good battery" signal to the control as soon as the
  • Honeywell VISTA 15P | User Guide - Page 46
    . TYPICAL FIRE EMERGENCY DISPLAYS FIRE 01 MASTER BEDROOM 01 AC ALARM FIRE Silencing Fire Alarms and Clearing Memory of Alarm ALPHA DISPLAY KEYPAD FIXED-WORD DISPLAY KEYPAD 1. You can silence the alarm at any time by pressing the OFF key (the security code is not needed to silence fire
  • Honeywell VISTA 15P | User Guide - Page 47
    OFF and ∗ READY (zone 95) ∗ READY and # (zone 99) Press both keys of the key pair assigned for fire at the same time. 3 STAY and # (zone 96) DISPLAYS FOLLOWING MANUAL INITIATION OF A FIRE ALARM FIRE 95 ALPHA DISPLAY KEYPAD 95 AC ALARM FIRE FIXED-WORD KEYPAD National Security Systems Inc
  • Honeywell VISTA 15P | User Guide - Page 48
    the National Fire Protection Association's National Fire Alarm Code (NFPA 72) noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms CLOSED DOOR GARAGE BASEMENT floor_plan-001-V0 - 48 - National Security Systems Inc (800) 457-1999
  • Honeywell VISTA 15P | User Guide - Page 49
    Fire Alarm System (cont'd) THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS Emergency Evacuation CLOSET BEDROOM PORCH BEDROOM BATH BEDROOM 2ND for those missing. Choose someone to assure that nobody returns to the house - many die going back. National Security Systems Inc (800) 457-1999 - 49 -
  • Honeywell VISTA 15P | User Guide - Page 50
    code. Press TEST key. To turn OFF: Enter code. Press OFF key. Consult Phone Access User's Guide that accompanies the Phone Module. See the Panic Keys section for emergency functions programmed for your system. Note: Keys "A", "B", and "C" may have been programmed for other functions. The keypad
  • Honeywell VISTA 15P | User Guide - Page 51
    . RAPID BEEPING Keypad only a. TROUBLE b. MEMORY OF ALARM SLOW BEEPING Keypad only c. SYSTEM LOW BATTERY d. EXT. SOUNDER WIRING FAIL a. EXIT DELAY WARNING b. ENTRY DELAY WARNING FIRE is displayed; zone number of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95
  • Honeywell VISTA 15P | User Guide - Page 52
    [✱] key is pressed. a. TROUBLE. b. MEMORY OF ALARM. c. SYSTEM LOW BATTERY. d. EXT. SOUNDER WIRE FAIL. a. EXIT DELAY WARNING (if programmed). b. ENTRY DELAY WARNING. a. CHECK displayed. Descriptor of troubled protection zone is displayed. b. FIRE or ALARM is displayed; descriptor of zone in alarm
  • Honeywell VISTA 15P | User Guide - Page 53
    user may be required to take adequate measures. RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15 This device complies with part 15 service. Connection user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected be connected
  • Honeywell VISTA 15P | User Guide - Page 54
    doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d'inspection des installations électriques, ou à un électricien, selon le cas. AVIS : L'indice d'équivalence sonnerie de tous les dispositifs n'excède pas 5. - 54 - National Security Systems Inc (800) 457-1999
  • Honeywell VISTA 15P | User Guide - Page 55
    Personal • Emergency Key**: Silent Alarm • Emergency Key**: Audible Alarm • Emergency Key**: Fire • Device Activation Device: * Features marked with this single asterisk apply to the VISTA-20P Series only. ** Emergency Keys: A = [1] / [∗] B C = [3] / [#] National Security Systems Inc (800
  • Honeywell VISTA 15P | User Guide - Page 56
    records. To program a user attribute: Enter system/partition* master code + [8] + user no. + "#" command listed in column heading. User No. 01 User Name installer User's Part(s).† Security (system master only) Code [#] [3] + part(s) + [#] enter new code (all) 02 system master (all) 03
  • Honeywell VISTA 15P | User Guide - Page 57
    Users 34-49 apply to VISTA-20P Series only; user 33 is partition 2 master for VISTA-20P Series, and the last user for VISTA-15P Series. Paging Setup Pager Phone Number\ Pager Prefix Characters 1 Automatically Reports Upon... open/close alarm/trouble zone list p1 p2 p1 p2 p1 p2 Sched. Func. Key
  • Honeywell VISTA 15P | User Guide - Page 58
    System Features Log (cont'd) Schedules*: master code + [#] + [6] [4] No. Event Device No. 15 16 17 18 Description Schedule No. Function Key (** VISTA-20P Series can use devices 01-16; VISTA-15P Series can only use devices 01-08; both can use trigger devices 17/18.) - 58 - National Security
  • Honeywell VISTA 15P | User Guide - Page 59
    Company: Policy No.: VISTA-20P / VISTA-15P Other (circle the appropriate model number) Type of Alarm: Burglary Fire Both Installed by: Name Serviced by: Address B. Weekly continued on other side Name Address Fire Dept. Other National Security Systems Inc (800) 457-1999 - 59 -
  • Honeywell VISTA 15P | User Guide - Page 60
    Floor Windows All windows Interior locations All Accessible Openings, Including Skylights, Air Conditioners and Vents All Exterior Doors G. ADDITIONAL PERTINENT INFORMATION: Signature: Date: - 60 - National Security Systems Inc (800) 457-1999
  • Honeywell VISTA 15P | User Guide - Page 61
    - Notes - National Security Systems Inc (800) 457-1999 - 61 -
  • Honeywell VISTA 15P | User Guide - Page 62
    - Notes - - 62 - National Security Systems Inc (800) 457-1999
  • Honeywell VISTA 15P | User Guide - Page 63
    intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners
  • Honeywell VISTA 15P | User Guide - Page 64
    serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and maintains your security CONNECTION WITH installed and maintained alarm THE PURCHASE PRICE OF THE Honeywell International Inc. www.honeywell.com/security ÊK5309-1V4(Š K5309-1V4 10/04 Rev.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ADEMCO VISTA SERIES
VISTA-20P / VISTA-20PSIA
VISTA-15P / VISTA-15PSIA
Security Systems
User Guide
K5309-1V4
10/04
Rev. A
National Security Systems Inc (800) 457-1999