Hoover ONEPWR Emerge Complete with All-Terrain Dual Brush Roll Nozzle Stick Vacu - Page 3
Warning, Important
View all Hoover ONEPWR Emerge Complete with All-Terrain Dual Brush Roll Nozzle Stick Vacuum manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
MAINTENANCE WARNING: To reduce the risk of personal injury - Turn power switch off and remove battery before cleaning or servicing. This product contains no serviceable parts. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call customer service at 1-800-944-9200 prior to continuing use. Store the battery pack where the temperature is below 80° F and away from moisture. 2 To clean the cyclone, lift to remove. Clean dirt and debris. GENERAL MAINTENANCE TO REMOVE BACK BRISTLED BRUSHROLL: 1 Remove the powered nozzle from reach wand. Using your fingers or a coin, push and turn the brush roll lock counter-clockwise to release the brush roll. NOTE: The lock cannot be removed. 3 Clear debris from the brush roll with a dry cloth. Clear any dirt/debris from the end caps of the powered nozzle. IMPORTANT: Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove dirt, dust, oil, grease, etc. LUBRICATION: The motor and brush roll are equipped with bearings which contain sufficient lubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brushroll. EMPTYING THE DIRT CUP 1 Remove the battery pack. 2 Press button to release the dirt cup. 3 Hold the dirt cup over a trash bin and press the dirt cup release button to empty. Close the dirt cup, then replace it by rocking it back into place. CLEANING THE FILTER AND CYCLONE 3 Pull the filter away and tap to remove dirt. Rinse filter under warm water until water is clear. Allow filter to dry for 24 hours before reinserting. IMPORTANT: Do not use vacuum without the filter or cyclone in place. Do not use soap or other chemicals to clean. Dry filter completely, for up to 24 hours, before reinstalling into the product. 2 Pull the brush roll out of the nozzle with pull tab. To remove any threads or hair, cut along the groove of the brush roll. 3 Clear any dirt/debris from the end caps inside of the housing of the powered nozzle. 4 Install the dirt cup filter cover before reattaching the dirt cup. REMOVING AND CLEANING THE POWERED FLOORHEAD BRUSHROLL WARNING: Risk of personal injury - Brushroll may suddenly restart. Turn power switch off and remove battery before cleaning or servicing. WARNING: To reduce the risk of injury from moving parts - Remove Battery before Servicing. 4 Re-fit the brush roll into the housing and turn the brush roll lock clockwise to lock. TO REMOVE FRONT MICROFIBER BRUSHROLL: WARNING: To reduce the risk of injury from moving parts - Remove Battery before Servicing. 1 Remove the powered nozzle from reach wand. Using a coin, push and turn the brush roll lock counter-clockwise to unlock the Microfiber Brush Roll. 4 Re-fit the brush roll into the housing and turn the brush roll lock clockwise to lock. THERMAL PROTECTOR: A THERMAL PROTECTOR HAS BEEN DESIGNED INTO YOUR CLEANER TO PROTECT IT FROM OVERHEATING. WHEN THE THERMAL PROTECTOR ACTIVATES THE CLEANER WILL STOP RUNNING. If this happens proceed as follows: 1. Turn cleaner OFF and remove battery pack. IMPORTANT: If left turned on, the cleaner motor may restart unexpectedly. 2. Empty dirt cup. 3. Inspect the filter and cyclone for any obstructions. Clear obstructions if present. 4. After the battery pack is removed and the motor cools for 30 minutes, reinstall the battery pack. The thermal protector will deactivate and cleaning may continue. If thermal protector continues to activate after following the above steps, your cleaner needs servicing, call Customer Service at 1-800-922-9400. TROUBLESHOOTING WARNING: TO REDUCE THE RISK OF PERSONAL INJURY - TURN POWER SWITCH OFF AND REMOVE THE BATTERY BEFORE CLEANING OR SERVICING. THIS PRODUCT CONTAINS NO SERVICEABLE PARTS. IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-944-9200 PRIOR TO CONTINUING USE. SEE BEHIND THE BATTERY DOCK ON THE PRODUCT FOR MODEL NUMBER. 1 Pull open the lid of the dirt cup to access the filter. 2 Lift and rotate the brush away from the nozzle assembly.