Hunter 21978 Owner's Manual
Hunter 21978 Manual
 |
View all Hunter 21978 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hunter 21978 manual content summary:
- Hunter 21978 | Owner's Manual - Page 1
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Model No. Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 41225-01 20091204 ©2009 Hunter Fan Co. - Hunter 21978 | Owner's Manual - Page 2
on the top of the fan motor housing). Cautions and Warnings • READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION. SAVE THESE INSTRUCTIONS. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building - Hunter 21978 | Owner's Manual - Page 3
is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page. Fan Support System • Fan attaches directly to building structure. • Fan support system will hold full weight of the fan and light kit. Ceiling Hole • e outlet box - Hunter 21978 | Owner's Manual - Page 4
any hardware store or electrical supply house. 5-4. Make certain the wiring meets all national and local standards and ANSI/NFPA 70. You have now successfully prepared your ceiling fan site. For instructions to install your ceiling fan, go to your fan manual and continue with Section 2 • Installing - Hunter 21978 | Owner's Manual - Page 5
, follow the instructions included with each product. For quiet and optimum performance of your Hunter fan, use only Hunter speed controls. Support Brace Ceiling Outlet Box For ceilings higher than 8 feet, you can purchase Hunter extension downrods. All Hunter fans use sturdy 3/4" diameter - Hunter 21978 | Owner's Manual - Page 6
any parts are missing or damaged, contact your Hunter dealer or call Hunter Technical Support Department at 888-830-1326 (In Canada, call 1-866-268-1936). Preparing the Fan Site Before you begin installing the fan, follow all the instructions in "Preparing the Fan Site." Proper ceiling fan location - Hunter 21978 | Owner's Manual - Page 7
warning device, such as a tag, to the service panel. Isolator Ceiling Plate 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64" in diameter. 2-2. Your fan comes with three neoprene noise isolators ("Isolators - Hunter 21978 | Owner's Manual - Page 8
top housing. Make certain the housing sits flat on the adapter. 3-2. Install three (3) assembly screws and tighten them securely. Steps 3-1 - 3-2 Top Housing Assembly Screw Hanger Adapter Raised Tabs Assembly Screw Locations Hanger Adapter Raised Tabs 8 41225-01 • 12/04/09 • Hunter Fan Company - Hunter 21978 | Owner's Manual - Page 9
Fan WARNING: Fan may fall if not assembled as directed in these installation instructions. 4-1. Unbundle the wires from the fan. For Standard or Angled mounting: 4-2. To assemble fan to hang down from a flat or angled ceiling the ceiling. 4-6. Align the holes fan and place the hook on the ceiling - Hunter 21978 | Owner's Manual - Page 10
back through the ceiling plate into the outlet box. 5-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 10 41225-01 • 12/04/09 • Hunter Fan Company Wire Connector Dual Switch Wiring Single Switch Wiring - Hunter 21978 | Owner's Manual - Page 11
and align the tabs in the canopy with the slots in the ceiling plate. Turn the canopy counterclockwise until it locks into place and will not turn any more. 6-3. Insert and tighten the canopy screws securely. Step 6-2 Canopy Screw Canopy Step 6-3 11 41225-01 • 12/04/09 • Hunter Fan Company - Hunter 21978 | Owner's Manual - Page 12
Blades 7-1. Insert blade into slot. Align the holes on the blade with the holes in the fan motor. 7-2. Slide blade grommets onto the shafts of the blade assembly screws. 7-3. Attach the when using grommets and will not be a problem Blade Assembly Screw 12 41225-01 • 12/04/09 • Hunter Fan Company - Hunter 21978 | Owner's Manual - Page 13
Before proceeding with the next step make Step 8-1 sure you've located the arrow. Fan Note: You may have to rotate the fan blades in order to see the Trim arrow. 8-2. The (8) sides of the fitter Hole Step 8-2 Steps 8-4-8-5 Elongated Slots 13 41225-01 • 12/04/09 • Hunter Fan Company - Hunter 21978 | Owner's Manual - Page 14
Fitter (Continued) 8-6. Plug the upper and lower plug connectors together. The connectors are keyed Note: In compliance with U.S. Federal energy regulations, this ceiling fan contains a wattage saver that restricts the light kit to troubleshooting section 14 41225-01 • 12/04/09 • Hunter Fan Company - Hunter 21978 | Owner's Manual - Page 15
with the (2) larger outboard holes in the metal plate. Step 9-1 9-3. Guide the threaded tube and both the chains through the larger holes in the metal . 9-5. Assemble the finial to the bottom of the light fixture by guiding the (2) pull chains and threaded tube through the (3) openings in the - Hunter 21978 | Owner's Manual - Page 16
. The chain has two settings: ON and OFF. 10-4. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in fan off and let it come to a complete stop. Pull the reversing pullchain one time and then restart the fan. Reversing Pull Chain 16 41225-01 • 12/04/09 • Hunter Fan - Hunter 21978 | Owner's Manual - Page 17
11 • Troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly left or right
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
 |
 |
Type 2 Models
Type 2 Models
Type 2 Models
Form# 41225-01
20091204
©2009 Hunter Fan Co.
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
English
Español
Owner’s Guide and Installation Manual