Hunter 28079 Owner's Manual
Hunter 28079 Manual
 |
View all Hunter 28079 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hunter 28079 manual content summary:
- Hunter 28079 | Owner's Manual - Page 1
For Your Records and Warranty Assistance Model Name Catalog/Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual. 42625-01 • 08/27/06 - Hunter 28079 | Owner's Manual - Page 2
• Operating and Cleaning Your Ceiling Fan 12 9 • Troubleshooting 13 Your new Hunter® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your - Hunter 28079 | Owner's Manual - Page 3
use the accessories, follow the instructions included with each product. For quiet and optimum performance of your Hunter fan, use only Hunter speed controls. For ceilings higher than 8 feet, you can purchase Support Brace Hunter extension downrods. All Hunter fans use sturdy 3/4" diameter pipe - Hunter 28079 | Owner's Manual - Page 4
included Parts Guide. Check for any shipping damage to the motor or fan blades. If any parts are missing or damaged, contact your Hunter dealer or call Hunter Technical Support Department at 888-830-1326. Preparing the Fan Site Before you begin installing the fan, follow all the instructions in the - Hunter 28079 | Owner's Manual - Page 5
: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers prominent warning device, such as a tag, to the service panel. 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The - Hunter 28079 | Owner's Manual - Page 6
not assembled as directed in these installation instructions. Downrod 3-1. Unbundle the wires from the fan. For Standard or Angle mounting: Set the downrod through the canopy and canopy trim ring. Feed the wires from the fan through the downrod on one side of the pin in the ball. 3-3. Loosen - Hunter 28079 | Owner's Manual - Page 7
acceptable general-use switch in accordance with national and local electrical codes. 4-1. Before attempting installation, make sure the power is still to the black (ungrounded) and the black/white wire (ungrounded) from the fan CAUTION: Be sure no bare wire or wire strands are visible after making - Hunter 28079 | Owner's Manual - Page 8
and Canopy Trim Ring Step 5-1 Tab Groove Step 5-2 Step 5-3 Canopy Canopy Trim Ring WARNING: Failure to complete the following steps could cause the fan to fall. Note: It is recommended you use a magnetic tip screwdriver for the following steps. 5-1. Rotate the hanger ball so the tab in the - Hunter 28079 | Owner's Manual - Page 9
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets mounting screw through the blade iron, and attach lightly to the fan. Insert the second blade mounting screw, then securely tighten both - Hunter 28079 | Owner's Manual - Page 10
Light Kit Steps 7-1 - 7-3 Keyhole Upper Slot Switch Housing 10 Housing Assembly Screw WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two #6-32 x 3/8" housing assembly screws into the switch housing mounting plate - Hunter 28079 | Owner's Manual - Page 11
7-5. To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors are properly aligned before connecting - Hunter 28079 | Owner's Manual - Page 12
light coat of furniture polish for added protection and beauty. Clean painted and high-gloss blades in the same manner as the fan finish. In cold weather, use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop. Slide the reversing switch on the - Hunter 28079 | Owner's Manual - Page 13
screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is properly seated. 9 • Troubleshooting 13 If you need parts or service assistance, please call 888‑830‑1326 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
 |
 |
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: ________________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
42625-01 • 08/27/06