Husqvarna 323R Owners Manual - Page 17

ASSEMBLY, Assembling the handlebars, 325RD, Transport position, handlebars

Page 17 highlights

Assembling the handlebars (323R) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Fit the bracket components as shown in the diagram. • The handle mounting must be fitted between the arrows on the shaft. • Loosely tighten the four screws. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it's attached to the harness. Tighten the screws. ASSEMBLY Assembling the handlebars (325RX, 325RXT, 325RDX) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Unscrew the bracket components from the handlebar bracket. • Position the handlebars as shown. Fit the bracket components and tighten the handle lightly. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it's attached to the harness. Tighten the handle. Transport position, handlebars (325RX, 325RXT, 325RDX) • The handlebars can easily be turned to fit along the shaft for easy transportation and storage. • Loosen the knob. Turn the handles clockwise so that the throttle comes against the engine. • Thereafter fold the handlebars around the shaft. Tighten the handle. • Attach the transport guard. English - 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

English
17
Assembling the handlebars
(323R)
ASSEMBLY
Assembling the handlebars
(325R
X
, 325R
XT
, 325RD
X
)
Remove the screw at the
rear of the throttle handle.
Slide on the throttle
handle on the right-hand
side of the handlebars, (see
the diagram).
Align the hole in the
throttle handle for the
fixing screw with the hole
on the handlebars.
Refit the screw in the rear
of the throttle handle.
Fit the screw through the
throttle handle and the
handlebars and tighten.
Unscrew the bracket
components from the
handlebar bracket.
Position the handlebars as
shown. Fit the bracket
components and tighten
the handle lightly.
Put on the harness and
hang the machine in the
suspension hook. Now
finely adjust so that the
machine gives a
comfortable working
position when it
s
attached to the harness.
Tighten the handle.
The handlebars can easily
be turned to fit along the
shaft for easy
transportation and storage.
Loosen the knob. Turn the
handles clockwise so that
the throttle comes against
the engine.
Thereafter fold the
handlebars around the
shaft. Tighten the handle.
Attach the transport
guard.
Transport position, handlebars
(325R
X
, 325R
XT
, 325RD
X
)
Remove the screw at the
rear of the throttle
handle.
Slide on the throttle
handle on the right-hand
side of the handlebars,
(see the diagram).
Align the hole in the
throttle handle for the
fixing screw with the
hole on the handlebars.
Refit the screw in the
rear of the throttle
handle.
Fit the screw through the
throttle handle and the
handlebars and tighten.
Fit the bracket
components as shown in
the diagram.
The handle mounting
must be fitted between
the arrows on the shaft.
Loosely tighten the four
screws.
Put on the harness and
hang the machine in the
suspension hook. Now
finely adjust so that the
machine gives a
comfortable working
position when it
s
attached to the harness.
Tighten the screws.