Husqvarna 365 X-Torq Owners Manual
Husqvarna 365 X-Torq Manual
 |
View all Husqvarna 365 X-Torq manuals
Add to My Manuals
Save this manual to your list of manuals |
Husqvarna 365 X-Torq manual content summary:
- Husqvarna 365 X-Torq | Owners Manual - Page 1
Operator's manual 365 X-Torq 372XP X-Torq 372XPG X-Torq Please read the operator's manual carefully and make sure you understand the instructions before using the machine. English - Husqvarna 365 X-Torq | Owners Manual - Page 2
instructions before using the machine. Always wear: • Approved protective helmet • Approved hearing protection • Protective goggles or a visor Symbols in the operator's manual: Switch off the engine the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar - Husqvarna 365 X-Torq | Owners Manual - Page 3
: EPA III The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Maintenance, replacement, or repair of the emission control devices and system may be performed - Husqvarna 365 X-Torq | Owners Manual - Page 4
KEY TO SYMBOLS Symbols on the machine 2 Symbols in the operator's manual 2 CONTENTS Contents 4 INTRODUCTION Dear customer 5 WHAT IS WHAT? 22 General working instructions 22 How to avoid kickback 28 MAINTENANCE General 29 Carburetor adjustment 29 Checking, maintaining and servicing chain saw - Husqvarna 365 X-Torq | Owners Manual - Page 5
, service, maintenance etc) the life span and the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the operator′s manual, so they will also know how to properly maintain and use it. Thank you for using a Husqvarna - Husqvarna 365 X-Torq | Owners Manual - Page 6
20 Throttle control 21 Throttle lockout 22 Decompression valve 23 Combination spanner 24 Chain tensioning screw 25 Operator's manual 26 Transport guard 27 Switch for heated handle (Model 372XPG X-Torq) 28 Information and warning decal 29 Product and serial number plate 30 Oil pump adjustment screw - Husqvarna 365 X-Torq | Owners Manual - Page 7
authorized accessories or replacement parts. ! WARNING! A chain service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions to the eyes. WARNING! Running an engine in a ! confined or badly - Husqvarna 365 X-Torq | Owners Manual - Page 8
instructions under the heading Checking, maintaining and servicing chain saw safety equipment. See instructions under the heading, What is what?, to find where these parts brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. 8 - English - Husqvarna 365 X-Torq | Owners Manual - Page 9
let go. A • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum). • The way the chain brake is activated, either manually or automatically by the inertia release mechanism, depends on the force of the kickback and the - Husqvarna 365 X-Torq | Owners Manual - Page 10
working order. Testing the brake is simple, see instructions under the heading Checking, maintaining and servicing chain saw safety equipment. We recommend you do vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit. The - Husqvarna 365 X-Torq | Owners Manual - Page 11
Stop switch Use the stop switch to switch off the engine. Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. General rules • Only use cutting equipment recommended by us! See instructions under the heading Technical data. • Keep the chain - Husqvarna 365 X-Torq | Owners Manual - Page 12
bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement through the wood and produces long, thick chips or shavings. • The cutting part of the chain is called the cutter and consists of a cutting tooth (A) - Husqvarna 365 X-Torq | Owners Manual - Page 13
will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain. A C B WARNING! The risk of kickback is - Husqvarna 365 X-Torq | Owners Manual - Page 14
not sag from the underside of the bar. The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model. Lubricating cutting equipment WARNING! Poor lubrication of cutting ! equipment - Husqvarna 365 X-Torq | Owners Manual - Page 15
each time you refuel. See instructions under the heading Lubricating the bar once a week). NOTE! Use only high quality bearing grease or engine oil. • Check that the groove in the edge of the checks and associated measures you should contact your servicing dealer. Check the chain daily for: • - Husqvarna 365 X-Torq | Owners Manual - Page 16
these with a file if necessary. • Whether the groove in the bar has become badly worn. Replace the bar if necessary. Wear personal protective equipment. See instructions under the heading "Personal protective equipment". Do not tackle any job that you feel you are not adequately trained for. See - Husqvarna 365 X-Torq | Owners Manual - Page 17
Fitting the bar and chain ASSEMBLY Tension the chain by turning the chain tensioning screw clockwise using the combination spanner. See instructions under the heading Tensioning the chain. WARNING! Always wear gloves, when ! working with the chain. Check that the chain brake is in disengaged - Husqvarna 365 X-Torq | Owners Manual - Page 18
instructions under the heading Carburetor). Running-in Avoid running at a too high speed for extended periods during the first 10 hours. Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine components. • Contact your service agent when choosing chain oil. 18 - English - Husqvarna 365 X-Torq | Owners Manual - Page 19
your clothes, change your clothes. Wash any part of your body that has come in contact with instructions under the heading Maintenance schedule. Ensure the machine is cleaned and that a complete service is carried out before long-term storage. Fuel safety • Never refuel the machine while the engine - Husqvarna 365 X-Torq | Owners Manual - Page 20
you have a secure footing and that the chain cannot touch anything. Keep people and animals well away from the working area. Starting Cold engine Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards. Ignition - Husqvarna 365 X-Torq | Owners Manual - Page 21
loose and cause serious injury. • The chain brake should be activated when starting. Se instructions under the heading Start and stop. Do not drop start. This method is very dangerous the chain saw handles. Stopping The engine is stopped by pushing the stop switch to the stop position. English - 21 - Husqvarna 365 X-Torq | Owners Manual - Page 22
and not damaged. 8 Check that all parts of the chain saw are tightened correctly . Contact your chain saw dealer, service agent or an experienced chain saw and how to avoid them. See instructions under the heading How to avoid chain to jam. Always stop the engine before cleaning. General rules 1 If - Husqvarna 365 X-Torq | Owners Manual - Page 23
the handles! 5 In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. 3 Most kickback accidents happen during limbing. Make sure you are standing firmly and that there is nothing in the way that might make you trip - Husqvarna 365 X-Torq | Owners Manual - Page 24
engine damage). • Cutting from above = Cutting with a pulling chain. • Cutting from below = Cutting with pushing chain. Cutting with a pushing chain increases the risk of kickback. See instructions these problems by cutting in two stages; from the top and from the bottom. You need to support the - Husqvarna 365 X-Torq | Owners Manual - Page 25
. Turn the log and finish the cut from the opposite side. The log is supported at one end. There is a high risk that it will split. Start by cutting ). Finish by cutting from above so that the two cuts meet. The log is supported at both ends. There is a high risk that the chain will jam. Felling - Husqvarna 365 X-Torq | Owners Manual - Page 26
letting the tree fall onto another tree. It is very dangerous to remove a trapped tree and there is high accident risk. See instructions under the heading Freeing a tree that has fallen badly. IMPORTANT! During critical felling operations, hearing protectors should be lifted immediately when sawing - Husqvarna 365 X-Torq | Owners Manual - Page 27
that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw. The safest method is to use a winch - Husqvarna 365 X-Torq | Owners Manual - Page 28
. Do not use the kickback zone of the guide bar. Be extremely cautious and avoid contacting the log, other limbs or objects with saw as you move along the trunk. Cutting the trunk into logs See instructions under the heading Basic cutting technique. Kickback always occurs in the cutting plane - Husqvarna 365 X-Torq | Owners Manual - Page 29
mixture next time the filter is cleaned. This can give rise to serious engine damage. • Do not attempt to adjust the L and H jets beyond either stop as this could cause damage. • Now start the machine according to the starting instructions and let it warm up for 10 minutes. • Place the machine on - Husqvarna 365 X-Torq | Owners Manual - Page 30
is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine. Checking, maintaining and servicing chain saw safety equipment Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety - Husqvarna 365 X-Torq | Owners Manual - Page 31
let go of the front handle. The chain should stop immediately. With the engine turned off, hold the chain saw over a stump or other firm object the chain does not touch the ground or any other object. See the instructions under the heading Start and stop. • Check that the throttle control and - Husqvarna 365 X-Torq | Owners Manual - Page 32
type of muffler, you should clean the screen at least once a week. This is best done with a wire brush. A blocked screen will cause the engine to overheat and may lead to serious damage. Note! The screen must be replaced if it is damaged. If the screen is blocked the machine - Husqvarna 365 X-Torq | Owners Manual - Page 33
MAINTENANCE use a muffler if the spark arrestor screen is missing or defective. • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards. The muffler is designed to reduce the noise - Husqvarna 365 X-Torq | Owners Manual - Page 34
• Lift up the starter pulley. See instructions under the heading Changing a broken or worn filter must always be replaced. A HUSQVARNA chain saw can be equipped with different types malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption - Husqvarna 365 X-Torq | Owners Manual - Page 35
consists of: 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins only high quality bearing grease or engine oil. See instructions under the heading Cutting equipment. Husqvarna's chain oil, for other chain oils increase the oil flow by one step. WARNING! The engine - Husqvarna 365 X-Torq | Owners Manual - Page 36
filter and carburetor. Special measures are therefore often required: • Partly mask the air inlet on the starter to increase the working temperature of the engine. Temperature -5°C (23°F) or colder: Electrical carburetor heating (372 XPG) On models with the designation CARBURETOR HEATING there is an - Husqvarna 365 X-Torq | Owners Manual - Page 37
if necessary. Check that nuts and screws are tight. Check that the stop switch works correctly. Check that there are no fuel leaks from the engine, tank or fuel lines. On chain saws with a catalytic converter, check the cooling system daily. Monthly maintenance Check the brake band on the chain - Husqvarna 365 X-Torq | Owners Manual - Page 38
cutting length, inches/cm Pitch, inch/mm Thickness of drive links, inch/mm Drive sprocket type/teeth Chain speed at max. power, m/sec 365 X-Torq 372XP X-Torq 372XPG X-Torq 4,31/70,7 1,97/50 1,42/36 2700 3,6/4,9 @ 10 200 4,31/70,7 1,97/50 1,42/36 2700 4,1/5,6 @ 10 200 4,31/70,7 1,97/50 1,42 - Husqvarna 365 X-Torq | Owners Manual - Page 39
11T 0,058 11T 0,058 11T 0,058 11T 0,058 11T 0,058 11T Chain Type Husqvarna H42, Husqvarna H48 Husqvarna H42, Husqvarna H48 Husqvarna H42, Husqvarna H48 Husqvarna H42, Husqvarna H48 Husqvarna H42, Husqvarna H48 Husqvarna H42, Husqvarna H48 Drive link count 56 60 68 72 84 92 Note: For the - Husqvarna 365 X-Torq | Owners Manual - Page 40
, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer.You are responsible for presenting your small nonroad engine to a Husqvarna Forest & Garden authorized servicing dealer as soon as a problem exists. The warranty repairs should be completed - Husqvarna 365 X-Torq | Owners Manual - Page 41
REPAIR OF EMISSION-RELATED PARTS Any Husqvarna Forest & Garden approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without the performance of all required maintenance, as defined in the operator's manual. English - 41 - Husqvarna 365 X-Torq | Owners Manual - Page 42
. Do not let the nose of the guide bar contact a log, branch, or any other obstacle which could be hit while you are operating the saw. Cut at high engine speeds. Do not overreach or cut above shoulder height. Follow manufacturer's sharpening and maintenance instructions for the saw chain. Only use - Husqvarna 365 X-Torq | Owners Manual - Page 43
- Husqvarna 365 X-Torq | Owners Manual - Page 44
Original instructions 1152677-95 ´´®®zz++TTccoo¶¶55GG¨¨ 2010-05-20
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
English
365
X-Torq
372XP
X-Torq
372XPG
X-Torq
Operator’s manual
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.