Husqvarna 440 e-series Owners Manual

Husqvarna 440 e-series Manual

Husqvarna 440 e-series manual table of contents:

  • Husqvarna 440 e-series | Owners Manual - Page 1
    Operator's manual 440e TrioBrake 445e TrioBrake Please read the operator's manual carefully and make sure you understand the instructions before using the machine. English 1153159-95 Rev.2 2010-04-08
  • Husqvarna 440 e-series | Owners Manual - Page 2
    1 14 1 2 3 31 13 32 12 6 16 11 10 9 8 7 30 4 2 5 3 15 29 28 17 18 19 4 27 26 25 24 23 22 21 20 5 B E 6 7 8 9 A 10 B 11 12 13 14 15 16 17 2 - English 1153159-95 Rev.2 2010-04-08
  • Husqvarna 440 e-series | Owners Manual - Page 3
    18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 A 1153159-95 Rev.2 2010-04-08 English - 3
  • Husqvarna 440 e-series | Owners Manual - Page 4
    41 42 43 44 45 46 2 A 1 47 440e TrioBrake 48 49 50 445e TrioBrake 51 52 53 54 55 1 4 3 5 7 1 6,8 2 9 10 56 57 58 59 60 61 62 4 - English 1153159-95 Rev.2 2010-04-08
  • Husqvarna 440 e-series | Owners Manual - Page 5
    63 65 66 1 2 3 64 67 68 70 69 71 72 73 74 75 76 77 78 1 3 2 1 2 1 79 80 81 82 83 84 85 86 87 1153159-95 Rev.2 2010-04-08 English - 5
  • Husqvarna 440 e-series | Owners Manual - Page 6
    88 90 91 89 92 93 94 95 96 97 98 99 100 101 102 1 2 103 104 105 106 107 108 109 A B 110 111 112 113 6 - English 1153159-95 Rev.2 2010-04-08
  • Husqvarna 440 e-series | Owners Manual - Page 7
    KEY TO SYMBOLS Symbols on the machine and/or in the manual: WARNING! Chain saws can be dangerous! Careless or ... carefully and make sure you understand the instructions before using the machine. Always wear: ...Never operate a chain saw holding it with one hand only. Visual check. Contact of the guide ...
  • Husqvarna 440 e-series | Owners Manual - Page 8
    KEY TO SYMBOLS You will find the following labels on your chain saw: EPA III, CARB III (440e TrioBrake) The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which ...
  • Husqvarna 440 e-series | Owners Manual - Page 9
    ... Symbols on the machine and/or in the manual: ...CONTENTS Contents ...INTRODUCTION Dear customer! ...WHAT IS WHAT? What is what on the chain saw? ...GENERAL SAFETY ... working instructions ...How to avoid kickback ...MAINTENANCE General ...Carburetor adjustment ...Checking, maintaining and servicing ...
  • Husqvarna 440 e-series | Owners Manual - Page 10
    ...time. Think of this operator′s manual as a valuable document. By following its′ content (using, service, maintenance ... us at our website: www.usa.husqvarna.com What is what on the chain saw? (1) 1 2 3 4 5 6 7 8 9 Cylinder cover Decompression valve... guard 17 Muffler 18 Chain 19 Bar tip sprocket 20...
  • Husqvarna 440 e-series | Owners Manual - Page 11
    ...PRECAUTIONS Before using a new chain saw • • • Please read this manual carefully. (1) - (113) refer ... Assembly. Refuel and start the chain saw. See the instructions under the headings Fuel ... by the use of nonauthorized accessories or replacement parts. WARNING! A chain saw is a dangerous tool if...
  • Husqvarna 440 e-series | Owners Manual - Page 12
    ...under the heading Checking, maintaining and servicing chain saw safety equipment. If your ... brake (A) can either be activated manually (by your left hand) or automatically by the inertia release ... chain saw safety equipment. See instructions under the heading, What is what?, to find where these parts...
  • Husqvarna 440 e-series | Owners Manual - Page 13
    ...In the felling position the left hand is in a position that makes manual activation of the chain brake impossible. With this type of grip, that is ... be in working order. Testing the brake is simple, see instructions under the heading Checking, maintaining and servicing chain saw safety equipment. We ...
  • Husqvarna 440 e-series | Owners Manual - Page 14
    ...chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical ... of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar... and hole for chain tensioner. The bar must be matched to the chain saw design. (15...
  • Husqvarna 440 e-series | Owners Manual - Page 15
    GENERAL SAFETY PRECAUTIONS • The cutting part of the chain is called the cutter and consists of a cutting tooth...teeth on one side first, then turn the chain saw and file the teeth on the other ...achieve the recommended depth gauge setting. See instructions under the heading Technical data to find ...
  • Husqvarna 440 e-series | Owners Manual - Page 16
    ...checks and associated measures you should contact your servicing dealer. Chain drive sprocket ! ...of whether it is warm summer or cold winter weather. As a chain saw manufacturer we have developed an... quality bearing grease or engine oil. See instructions under the heading Maintenance, Needle bearing ...
  • Husqvarna 440 e-series | Owners Manual - Page 17
    .... Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check ... fit correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tension ... the heading General working instructions. Check that all the chain saw safety features are working...
  • Husqvarna 440 e-series | Owners Manual - Page 18
    ...longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only... be emptied and cleaned. • Environment fuel HUSQVARNA recommends the use of alkylate fuel or environmental... pump components. Contact your service agent when choosing chain oil. • 18 - English...
  • Husqvarna 440 e-series | Owners Manual - Page 19
    ...a fire. Transport and storage Always store the chain saw and fuel so that there is no.... See instructions under the heading Maintenance schedule. Ensure the machine is cleaned and that a complete service is ... your clothes, change your clothes. Wash any part of your body that has come in contact with ...
  • Husqvarna 440 e-series | Owners Manual - Page 20
    ... choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch ... front handle with your left hand. Hold the chain saw on the ground by placing your right foot ... choke, which is not needed when starting a warm chain saw. However the movement of the start/stop ...
  • Husqvarna 440 e-series | Owners Manual - Page 21
    ...firmly and rapidly until the engine fires. As the chain brake is still engaged the speed of the engine ...See instructions under the heading Assembly. Without a bar and chain attached to the chain saw ...into contact with the cutting equipment. Always hold the saw with both hands. The right hand should ...
  • Husqvarna 440 e-series | Owners Manual - Page 22
    ... attached and not damaged. Check that all parts of the chain saw are tightened correctly and that they are ... them. See instructions under the heading How to avoid kickback. Before using a chain saw you must ... trees. 3 NB! Follow the instructions above, but do not use a chain saw in a situation where ...
  • Husqvarna 440 e-series | Owners Manual - Page 23
    ... that you are cutting will split: the first is how the object is supported before and after cutting, and ... these problems by cutting in two stages; from the top and from the bottom. You need to support ... up the cut and free the chain saw. The following instructions describe how to handle the common ...
  • Husqvarna 440 e-series | Owners Manual - Page 24
    ... finish the cut from the opposite side. (70) The log is supported at one end. There is a high risk that ...tree and there is high accident risk. See instructions under the heading Freeing a tree that has fallen... lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. ...
  • Husqvarna 440 e-series | Owners Manual - Page 25
    ...directional cuts with single cutting strokes. See instructions under the heading Technical data section ... the log, other limbs or objects with the nose of the guide bar. Be extremely cautious of limbs under... side of the trunk. Work as close as possible to the chain saw for maximum control. If possible...
  • Husqvarna 440 e-series | Owners Manual - Page 26
    ... recommend you to contact our servicing dealer. Carburetor adjustment Your Husqvarna product has been... adjusted or repaired. With the engine turned off, hold the chain saw over a stump or other firm object... touch the ground or any other object. See the instructions under the heading Start and stop....
  • Husqvarna 440 e-series | Owners Manual - Page 27
    ...guard. Do not let go of the front handle. The chain should stop immediately. (52) spark plug cap... full throttle. Release the throttle control and check that the chain stops and remains stationary. If the ... is not damaged and is firmly attached to the body of the chain saw. (98) Right hand guard ! ...
  • Husqvarna 440 e-series | Owners Manual - Page 28
    ...Carburettor malfunctions Starting problems Loss of engine power Unnecessary wear to engine parts Excessive ... (A) • Lift up the starter pulley. See instructions under the heading Changing a broken or worn ...air filter must always be replaced. A HUSQVARNA chain saw can be equipped with different types...
  • Husqvarna 440 e-series | Owners Manual - Page 29
    ...temperature. Icing of the air filter and carburetor. Partly mask the air inlet on the starter to increase ... by loosening the two bar nuts. Lay the saw on its side with the clutch drum upwards. Lubrication... other than that described in this manual must be carried out by your servicing dealer (retailer...
  • Husqvarna 440 e-series | Owners Manual - Page 30
    ...spring. Monthly maintenance Check the brake band on the chain brake for wear. Replace when less than ...tip, this should be lubricated. Check that the bar and chain are getting sufficient oil. Check ... leaks from the engine, tank or fuel lines. On chain saws with a catalytic converter, check the cooling...
  • Husqvarna 440 e-series | Owners Manual - Page 31
    ...000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight Chain saw without bar or chain, empty tanks, lb/kg Chain/bar Standard bar length, inch/cm Recommended bar lengths,... drive links, inch/mm Drive sprocket type/teeth Chain speed at max. power, m/sec 15"/38 13-20/...
  • Husqvarna 440 e-series | Owners Manual - Page 32
    ... DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Husqvarna chain saw models 440e TrioBrake and 445e ... and vibration requirements of ANSI B175.1-2000. The guide bar nose radius is determined by either the ...
  • Husqvarna 440 e-series | Owners Manual - Page 33
    ... small off-road engine. In U.S. and Canada, new equipment that use small off... of the required maintenance listed in your operator's manual. Husqvarna Forest & Garden recommends that you... Forest & Garden authorized servicing dealers. WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or replacement...
  • Husqvarna 440 e-series | Owners Manual - Page 34
    ... and later small nonroad engine. In U.S. and Canada, new small nonroad engines must ... of the required maintenance listed in your Operator′s Manual. Husqvarna Forest & Garden recommends that you ... Garden authorized servicing dealers. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS Any ...
  • Husqvarna 440 e-series | Owners Manual - Page 35
    ... WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes ...and a planned retreat path from the falling tree. Keep all parts of your body away ... and maintenance instructions, should be performed by competent chain saw service personnel. (For example,...
  • Husqvarna 440 e-series | Owners Manual - Page 36
    The engine exhaust from this product contains chemical known to the State of California to cause cancer, birth defects or other reproductive harm. Original instructions 1153159-95 ´®z+U/•¶5&¨ ´®z+U/•¶5&¨ 2010-04-08



Type your new search above

The manual viewer requires the flash plugin to be installed and enabled.
To view this page ensure that Adobe Flash Player version 10 or greater is installed.

Husqvarna 440 e-series Manual