Husqvarna LTA18538 Operation Manual - Page 7

To Install Hood Scoop See Fig. 5, Connect Battery See Fig. 4

Get Husqvarna LTA18538 PDF manuals and user guides View all Husqvarna LTA18538 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

ASSEMBLY CONNECT BATTERY (See Fig. 4) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions.) • Determine battery location. Battery location will be under the seat or the hood. • Lift seat pan or hood to raised position. • Remove two terminal caps and discard. • First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal. • Connect BLACK grounding cable to negative (-) terminal with remaining bolt and nut. Tighten securely. TO INSTALL HOOD SCOOP (See Fig. 5) TERMINAL COVER NUT LABEL TERMINAL CAP BOLT POSITIVE (RED) CABLE 02605 Fig. 4 NEGATIVE (BLACK) CABLE Fig. 5 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
7
ASSEMBLY
TO INSTALL HOOD SCOOP (See Fig. 5)
Fig. 5
CONNECT BATTERY (See Fig. 4)
WARNING:
Do not short battery terminals
by allowing a wrench or any other object
to contact both terminals at the same
time. Before connecting battery, remove
metal bracelets, wristwatch bands, rings,
etc. Positive terminal must be connected
fi
rst to prevent sparking from accidental
grounding.
NOTE:
If this battery is put into service after month and
year indicated on label (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See
“BATTERY” in the Maintenance
section of this manual for
charging instructions.)
•
Determine battery location. Battery location will be
under the seat or the hood.
•
Lift seat pan or hood to raised position.
•
Remove two terminal caps and discard.
•
First connect RED battery cable to positive (+) terminal
with bolt and nut as shown. Tighten securely. Slide
terminal cover over terminal.
•
Connect BLACK grounding cable to negative (-)
terminal with remaining bolt and nut. Tighten securely.
Fig. 4
02605
NUT
POSITIVE
(RED)
CABLE
NEGATIVE
(BLACK)
CABLE
BOLT
TERMINAL
COVER
LABEL
TERMINAL
CAP